Fixed Outputs - Dry Contacts - socomec SIRCO MOT PV Instruction Manual

5.2.3. fixed outputs - dry contacts

5.2.3.1. Description
As standard, the SIRCO MOT PV is equipped with four fixed outputs located on
the motorisation module.
(Dry contacts to be powered by the user).
5.2.3.2. Position auxiliary contact
The SIRCO MOT PV is equipped with integrated position (I – O) auxiliary contact outputs through 3 off micro switches.
pins 13, 04, 24
(Normally Open contacts with pin 13 as common)
5.2.3.3. SIRCO MOT PV Product available output (motorisation)
pin 63a – 64a
(Normally Open contact that is held closed when the motorisation is available).
This contact gives constant feedback about the product's availability and it's capacity to operate.
The SIRCO MOT PV performs a self diagnostics test on the motorisation module at startup, when put from Manual
-> Auto and then every 5 minutes. This test ensures that the SIRCO MOT PV is operational in terms of control inputs.
Should one of the tests fail, a second test is performed to reconfirm the error state. Should the SIRCO MOT PV
motorisation module become unavailable, contact 63A – 64A are opened, the power/ready LED's are switched off,
and the fault LED is activated. The fault LED will remain active for as long as sufficient power is available and the fault
condition is not reset. The fault is reset when the product is switched from AUT -> Manual -> Auto mode.
SIRCO MOT PV (Motorisation) Product Available / Unavailable Watchdog relay will open for any of the following
reasons below: For added security, "Product Availability" is informative and does not necessarily inhibit motor
operation.
ProductUnavailable+WarningLEDCondition:
Product in manual mode
Motor not detected (Autotest)
Control voltage out of range
Operating factor fault active (N° of operations / min)
Powerfail active
Customer input autotest failed
Invalid product customisation
Abnormal switching when not in manual mode
Requested position not reached
Locked mode active when not in manual mode
External Fault -> User input
Unexpected current flowing through the motor when idle
Sampling rate for the above is every 10 ms
Exception: motor detection sampling rate is every 5 min
28 EN
1 2
75A413 200A
75A414 250A
75A415 400A
75A416 500A
75A417 630A
75A425 200A
75A426 250A
75A427 400A
75A428 500A
75A429 630A
75A430 I800A
75A431 1000A
75A432 1250A
75A433 1600A
75A434 2000A
75A436 3200A
3 4
Ue 750V 19PV3020
Ue 750V 19PV3025
Ue 750V 19PV3040
Ue 750V 19PV3050
Ue 750V 19PV3063
Ue 1000V 19PV4020
Ue 1000V 19PV4025
Ue 1000V 19PV4040
Ue 1000V 19PV4050
Ue 1000V 19PV4063
Ue 1000V 19PV4080
Ue 1000V 19PV4100
Ue 1000V 19PV4120
Ue 1000V 19PV4160
Ue 1000V 19PV4200
Ue 1000V 19PV4320
SIRCO MOT PV - 543 544 B - SOCOMEC
5
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
inhibition
Yes
No
Yes
Yes
Yes
No
No
Yes
Yes
Yes
No
Yes