Page 1
MedSurg Bed Model FL23SE (Electric) Maintenance Manual For Parts or Technical Assistance: USA: 1-800-327-0770 (option 2) Canada: 1-888-233-6888 2008/08 72-1048E MM FL23SE REV A www.stryker.com...
Introduction InTended USe This manual is designed to assist you with the maintenance of Stryker Model FL23SE Electrical MedSurg Bed. Carefully read this manual thoroughly before using the equipment or beginning maintenance on it. To ensure safe operation of this equipment, it is recommended that methods and procedures be established for educating and training staff on the safe operation of this bed.
220V~, 50-60Hz, 2.9A - Two 250V, 6.3A Slow Blow Fuses 240V~, 50-60Hz, 2.7A - Two 250V, 6.3A Slow Blow Fuses Stryker reserves the right to change specifications without notice. Specifications listed are approximate and may vary slightly from unit to unit or by power supply fluctuations.
This provides special information to make maintenance easier or important instructions clearer. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
(Weee), this symbol indicates that the product must not be disposed of as unsorted municipal waste, but should be collected separately. Refer to your local distributor for return and/or collection systems available in your country. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Preventative Maintenance WarnIng Use only replacement parts provided by Stryker. annUal CheCklIST All fasteners secure. ______ Inspect for excessive wear the oil-impregnated bronze shoulder spacers found at the bed hinge points. ______ Replace as needed. do not lubricate these spacers.
Cleaning Stains: Wash with lukewarm water using a mild detergent. Rinse with water and let dry. For tough stains, use bleach diluted with ten parts of water. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
The foot board command is used. of the removable pendant control (optional) properly connected to the bed connector under the mattress support? • Check points of the “No power to bed” problem described above. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Page 16
Improper operation of the CPR emergency release • Check and replace if needed the two CPR mechanism (optional): Knee Gatch does not lower and/or the Fowler limit switches (see 54). actuator does not reset. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
The parts and accessories listed on this page are all currently available for purchase. Some of the parts identified on the assembly drawing parts in this manual may not be individually available for purchase. Please call Stryker Customer Service USA: 1-800-327-0770 (Option 2) or Canada: 1-888-233-6888 for availability and pricing.
Page 18
Wheel Cover - Right (Optional) QP28-0299-07 Wheel Cover - Left (Optional) QP28-0300-07 Brake/Steer Pedal QP23-0627 Velcro Fastener 25-0550 Miscellaneous Grey Spray Paint DDCAP-GSP Shoulder Spacer QDF17-0020 Nylon Cable Tie QDF9518 Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Place the static control wrist strap on your wrist. Connect the clip at the other end of the wrist strap cord to a ground point on the bed. GROUNDING DIAGRAM Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
• 1/4” Ratchet (with 6” extension) and 5/16” Socket • Bungee Cords • OG2 Grease • Brush Screw Covers Screw Covers Shown Are Optional Shown are optional figure 2.2 Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 21
Using a brush, apply grease on the threads of the bed lift actuators screws. Optional dust tubes may be present, if so, simply apply grease through the dust tube side openings. Using the electric controls, raise and lower the bed several times to spread the grease evenly. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
3/8” Drive Ratchet • Small Slotted Head Screwdriver • Long Nose Pliers • Retaining Ring Pliers • Rubber Mallet • 7/16” Socket right head Siderail Shown figure 4.1 a Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 23
Inspect the self-lubricating bearings for wear and replace them if need be. Reverse the above steps to install the replacement rail. Verify the siderail movement for proper operation before returning the bed to service. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
First, remove the two locknuts and bolts at one end of the assembly and, while holding the assembly, finish with the ones at the opposite end. Reverse the above steps to install the replacement siderail assembly. Verify the siderail for proper operation before returning the bed to service. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
At assembly, tighten the two locknuts to a 75 in/lb torque using the torque wrench. Reverse the above steps to install the replacement transfer plate. Verify the siderail for proper operation before returning the bed to service. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Apply grease on a 4” distance from both ends of the tube. Reverse the above steps to install the replacement pivot tube. Verify the siderail movement before returning the bed to service. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Hold the rail firmly when removing the last bolts. Reverse the above steps to install the replacement rail. Verify the siderail movement before returning the bed to service. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Reverse the above steps to install the replacement siderail assembly. Verify the siderail for proper operation before returning the bed to service. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Use the same procedure to insert the upper part of the new handle on the rod, but this time turn the lock rod up. Reverse the above steps to install the replacement release handle. Verify the release handle for proper operation before returning the bed to service. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Using the two 1/2” combination wrenches, remove locknut, shoulder spacer and bolt (J) holding the locking hook to the plate. Remove hook. Reverse the preceding steps to install the new hook. Verify siderail for proper operation before returning the bed to service. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Using the No. 2 Phillips screwdriver, remove the three screws, washers and spacers (D) holding the panel to the cover. Reverse the above steps to install the new control panel. Verify all the controls of the foot end control panel before returning the bed to service. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Keep the seal for the replacement connector. Reverse the above steps to install the new connector. Verify all the controls of the foot end control panel for proper operation before returning the bed to service. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Reverse the above steps to install the replacement foot board panel. Verify all the controls of the foot board panel for proper operation before returning the bed to service. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
(D) holding the connector to its support. Remove the defective connector. Reverse the above steps to install the replacement connector. Verify the foot board controls for proper operation before returning the bed to service. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Make sure to connect the membrane cables before fastening together the two sections of the control panel housing. Stick the membranes to the support at the end of the replacement procedure. Verify all the siderail functions for proper operation before returning the bed to service. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Using the 1/2” combination wrench, remove the two locknuts, washers, shoulder spacers and bolts (D) linking the foot section to the thigh section and remove the defective section. Reverse the above steps to install the new foot section. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Using the 1/2” combination wrench, remove the four locknuts, washers, shoulder spacers and bolts (D, E) linking the thigh section to the foot and seat sections and remove the thigh section. Reverse the above steps to install the replacement thigh section. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Remove the four rubber caps (K) covering the screws (L) holding the stops (M) to the defective section and replace the parts on the replacement section. Reverse the above steps to install the replacement seat section. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
If the bed is not equipped with the CPR emergency release (optional), proceed with steps 7 to 14. Otherwise, proceed with steps 15 to 24. figure 4.3 B Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Page 42
Verify the CPR emergency release and the Auto Contour positioning (optional) for proper operation before returning the bed to service. end of the procedure for beds with CPr and auto Contour. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
• No. 2 Phillips Screwdriver • Diagonal Pliers • 5/16” Socket • Small Regular Head Screwdriver • Pliers • Bungee Cord • 1/4” Drive Ratchet Procedure: figure 4.3 C Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Page 44
Before installing the rue ring cotter to finalize the head actuator replacement, raise and lower completely the Fowler. Check that the actuator stops working as soon as the head section reaches the frame. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
It is of utmost importance that the course of the replacement thigh actuator be adjusted before hooking up its tube to the thigh section lever arms. An improper adjustment can damage the thigh section structure. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Page 46
Before installing the rue ring cotter to finalize the head actuator replacement, raise and lower completely the Knee Gatch. Check that the actuator stops working as soon as the thigh section reaches the frame. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
(optional) and keep it for the replacement actuator. Reverse the above steps to install the replacement actuator. Take note of the following caution before hooking up the motor to the bed lift lever. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Page 48
Link the motor to the bed lift lever. The alignment jigs still in position, completely raise and lower the bed to ensure that the lower limit has been preserved following the motor replacement. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Do not over tighten the nut. Reverse the above steps to install the replacement transformer. Test all the bed electric controls for proper operation before returning the bed to service. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Keep the jumper (W1) that is located on the electronic board before replacing the board. Reverse the above steps to install the replacement control board. Test all the bed electric functions before returning the bed to service. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Reverse the above steps to install the replacement power connector. Turn the power switch on and check that the bed is powered before returning it to service. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
This switch signals to the motor control board that the Knee Gatch must be lowered. The signal is sent during the lowering of the Fowler when the bed is in the Auto Contour position. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 53
Using the No. 1 Phillips screwdriver, remove the two screws (D) holding the switch to the support. Reverse the above steps to install the replacement micro switch. Test the Auto Contour positioning for proper operation before returning the bed to service. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Service Information CPr MICro SWITCh rePlaCeMenT (oPTIonal) Tools required: • Inclinometer • No. 1 Phillips Screwdriver • No. 2 Phillips Screwdriver Procedure: figure 4.3 f Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 55
Using the regular screwdriver, remove the micro switch from its support. Reverse the above steps to install the replacement micro switch. Test the CPR emergency release before returning the bed to service. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Make sure there is no loose space at the CPR handle once the replacement cable is installed. Test the CPR emergency release before returning the bed to service. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
(N). Note the location of the locknut before loosening it so the replacement cylinder will be properly screwed into the end fitting. Reverse the above steps to install the replacement cylinder. Test the CPR emergency release for proper operation before returning the bed to service. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
62) on the side of the defective pedal and lay the support down. Keep the molded spacer (B). Remove the pedal from the activation lever shaft. Use a rubber mallet if necessary. Reverse the above steps to install the replacement pedal. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Position the brake/steer pedal to neutral. Using two 1/2” combination wrenches, remove the nut and bolt (C) holding the caster to the swing arm. Reverse the above steps to install the replacement caster. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Remove and keep the two locking levers (G, Figure 4.4 B, 62). Reverse the above steps to install the replacement fifth wheel assembly. Test the fifth wheel for proper operation before returning the bed to service. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Reverse the above steps to install the replacement swing arm assembly. Test the fifth wheel for proper operation before returning the bed to service. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Remove, using needle nose pliers, the rue ring, washer and locking axle (A) linking the caster shaft to the locking lever (B) and the brake rod (C) if the caster is part of the braking system. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 63
Reverse the above steps to install the replacement caster. If the replacement caster is part of the brake mechanism, apply the brakes and check that the caster is locked before returning the bed to service. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Using a 1/2” combination wrench, remove the nut, shoulder spacer, washer and bolt (E1, E2) holding each end of the linking rod. Remove the defective linking rod. Reverse the above steps to install the replacement linking rod. Check the braking mechanism before returning the bed to service. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Base (for reference only: l23-006g, rev. 01) Item Part no. Part name Qty. 25-0108G Base S.A. 28-0469 Ground Chain VV83A9G16 Tapping Screw Pan Type B Phillips #10 x 1/2” z.p. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Part no. Part name Qty. QP25-0299-07 Right Caster Cover 25-0550 Caster Hood Velcro QP28-0300-07 Left Caster Cover VV81A9E16 Tapping Screw Type B Flat Head Phillips # 8 x 1/2 z.p. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 67
Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Flat Head Hexagonal Socket Cap Screw 5/16-18 UNC x 1 1/4” z.p. VV11A1P48 Flat Head Hexagonal Socket Cap Screw 3/8-16 UNC x 2” z.p. VVB4A1O32 Bolt 5/16” - 18 X 1” Thread Rolling Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Foot Cover Plate QP23-0257 Mattress Support Glide VE20A1N Locknut 1/4-20 QDF132X “Perma-Stick” Anti-Cold Stopper VV83A9G16 Tapping Screw Pan Phillips Type B #10 x 1/2” z.p. QE71-1069 Frame Protector Sticker Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Item Part no. Part name Qty. QDF20-0081 100V Connector QDF8078 10A, 250V Long Fast Action Fuse QED9575 Fuse Holder QE71-0571 Sticker - 10A, 250V Fuses QE71-1194 100V CSA Sticker Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
International electric System For Reference Only: OL230230 Rev. 00 DETAIL A 8 10 Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Page 90
Type F #4-40 x 5/8” zp VV83A9G16 Tapping Screw Pan Phillips Type B #10 x 1/2” z.p. VV84A1H46 Flanged Hexagonal Head Tapping Screw #12 X 1/2 Type B z.p. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Nylon Ty-Rap Black (0.143 X 8”) VV83A9G16 Tapping Screw Pan Phillips Type B #10 x 1/2” z.p. VV87A9A20 Tapping Screw Truss Phillips Socket #4 x 5/8” Type B z.p 23-0452G Angle Sensor Arm Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Bed lift Motors Screw Covers (for reference only: ol230091, rev. 01) Item Part no. Part name Qty. QP23-0256 Screw Cover VV83A9G12 Tapping Screw Pan Phillips Type B #10 x 3/8” z.p. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 99
Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Bolt 5/16” - 18 X 3/4” Thread Rolling VW10A10 Flat Washer 5/16” SAE z.p. 17-0211G Foot End Mattress Retainer 23-0815 Centre Section Stop VV83A9G36 Type B Screw, #10 X 1-1/4 28-0468Z Left Hook Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Control Panel For Reference Only: OL230026 Rev. 04 Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 103
Nurse Control Membrane QDF7826 3M Adhesive Tape #950 x 1” .1250 VV83A9G16 Tapping Screw Pan Phillips Type B #10 x 1/2” z.p. VW60C201320 Nylon Spacer 5/8” x .386” x 39/64” Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Control Panel on frame for full-length For Reference Only: OL230209 Rev. 01 Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 105
Nurse Control Board VV83A9G16 Tapping Screw Pan Phillips Type B #10 x 1/2” z.p. VW60C201320 Nylon Spacer 5/8” x .386” x 39/64” QDF7826 3M Adhesive Tape #950 x 1” .2500 Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Board Control Panels - full-length Siderail For Reference Only: OL230210 Rev. 01 Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 109
Type B #10 x 1/2” z.p. VW10A06 Flat Washer # 10 z.p. VW60C201320 Nylon Spacer 5/8” x .386” x 39/64” QDF7826 3M Adhesive Tape #950 x 1” .2500 QDF2053 Red PVC Tape .5000 Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Sleeve 25-0514Z Cylinder Inner Sleeve 25-0515Z Cylinder Outer Sleeve M0008 Threadlocker - Medium Strength (Blue) .3000 M0019 Petro Canada OG2 Grease .0450 QDF17-0020 Shoulder Spacer Diameter 5/16” x 0.210” Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Page 114
Nylon Shoulder Washer (ID 270” x D 480” x OD 720”) VE20AOP Locknut M10 x 1.0 z.p VV87A9A24 Tapping Screw Truss Phillips Socket #4 x 1/2” QDF9159 Cherry Limit Switch Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 115
Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Sticker - Left Pedal Positions QE71-0741-T Sticker - Mattress Maximum Thickness QE71-0749-T Serial Number Plate QE71-0752-F Fire Hazard - Sticker QE71-0778-F Sticker - Accessory Warning VR11H43 Dome Head Pop Rivet #43 Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Sticker - Left Pedal Positions QE71-0741-T Sticker - Mattress Maximum Thickness QE71-0749-T Serial Number Plate QE71-0752-E Fire Hazard - Sticker QE71-0778-E Sticker: Accessory Warning VR11H43 Dome Head Pop Rivet #43 Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
BnQ Certification For Reference Only: OL230258 Rev. 00 BnQ Certification (for reference only: ol230258, rev. 00) Item Part no. Part name Qty. QE71-1201-F BNQ Sticker Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 121
Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
QE71-0742-T Power Source Label VV37A1C12 Machine Screw Truss Phillips #6-32 x 3/8” z.p. VV83A9G16 Type B Pan Phillips Tapping Screw #10 x 1/2” z.p. QE71-0225-T Sticker - Circuit Breaker Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Part name Qty. 25-0273Z Night Light Support QDF18825 Interlocking Outlet QDF9539 Night Light QE71-0712 Sticker - Night Light VV83A9G16 Tapping Screw Pan Phillips Type B #10 x 1/2” z.p. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Cable and Phone Plug 1/4” For Reference Only: OL230215 Rev. 00 Cable and Phone Plug 1/4” (for reference only: ol230215, rev. 01) Item Part no. Part name Qty. QDF23-0571 Mono Wall Connection Cable Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Page 126
Bolt 1/4”-20 x 3/4” Grade 5 z.p. VB15A1O54 Bolt 5/16-18 x 2 3/4” LG Full Thread 2 VE30A1N Nylon Locknut 1/4-20 VE30A1O Nylon Locknut 5/16”-18 VW10A10 Flat Washer Diameter 5/16” S.A.E. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 127
Bolt 1/4”-20 x 3/4” Grade 5 z.p. VB15A1O44 Bolt 5/16-18 x 1 3/4” LG Grade 5 VE30A1N Nylon Locknut 1/4-20 VE30A1O Nylon Locknut 5/16”-18 QPN14-0705 Caster for Head Lever Arm Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Page 128
Install the wheel’s side with the clamping hole toward the exterior of the bed 0.13”...
Page 129
Nylon Locknut 5/16”-18 VV60A0G08-S Hexagone Pressure Screw #10-32 x 1/4” LG Scotch Grip VW10C122402 Nylon Washer 0.380” Int. x 3/4” ext. x 1/16” wi. QPN14-0705 Caster for Head Lever Arm Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Page 130
Short Bed Bumper For Reference Only: OL230244 Rev. 00 Short Bed Bumper (for reference only: ol230244, rev. 00) Item Part no. Part name Qty. QPPE1207 Plastic Cap 1/4 QP23-0776 Glider Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Power Cord with Straight Molded north american hospital grade Plug (for reference only: ol250053, rev. 01) Item Part no. Part name Qty. QDF8066 Power Cord with Straight Molded North American Hospital Grade Plug 1 Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
For Reference Only: For Reference Only: OL250068 OL250069 OL250073 OL250074 Rev. 01 Rev. 01 Rev. 01 Rev. 01 Part number: Part number: Part number: Part number: QDF8066-ISR QDF8066-ITA QDF8066-ARG QDF8066-CHI Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 139
VV23A9C16HL Phillips Pan Head High-Low Tapping Screw Type B #6 x 1/2” VV61A0M08 Nylon Tipped Hexagonal Socket Set Screw 1/4-28 x 1/4” VW10A10 Flat Washer Diameter 5/16” S.A.E. z.p. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Page 140
VV23A9C16HL Phillips Pan Head High-Low Tapping Screw Type B #6 x 1/2” VV61A0M08 Nylon Tipped Hexagonal Socket Set Screw 1/4-28 x 1/4” VW10A10 Flat Washer Diameter 5/16” S.A.E. z.p. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
PvC Protector for full-length Siderail (for reference only: ol230208, rev. 01) Item Part no. Part name Qty. 23-0641 Full-Length Siderail PVC Protector QDF7826 3M Adhesive Tape #950 x 1” Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Page 145
Control Board Stand-off Pin QDF7908 Black Plug 1” #SQR-1-10-14 QDF9018 “AMP” Pin Contact #66103-2 QDF299X Adhesive Neoprene 1/4 x 3/4 .1666 QDF2043 Cable Clamp “AMP” 206070-1 QDF2042 14-Positions Circular Connector Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Page 146
Control Board Stand-off Pin QDF7908 Black Plug 1” #SQR-1-10-14 QDF9018 “AMP” Contact Pin #66103-2 QDF299X Adhesive Neoprene 1/4 x 3/4 .1666 QDF2043 Cable Clamp “AMP” 206070-1 QDF2042 14-Positions Circular Connector Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 147
Raise Fowler Brown Raise Bed Blue Raise Gatch Orange Communication Black Lower Gatch White Lower Bed Green Lower Fowler Normally Open Buzzer Yellow Communication Buzzer Grey Normally Closed Buzzer Purple Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Siderails with removable Controls For Reference Only: OL230246 Rev. 00 Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 149
Siderails with removable Controls 10.00” 10.00” Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Page 151
Type B #10 x 3/4” VW10A08 Flat Washer 1/4” x 1/16” M0019 Petro Canada OG2 Grease .0300 QP23-0735 PCB Support QDF7908 Black Plug 1” #SQR-1-10-14 QDF299X Adhesive Neoprene 1/4 x 3/4 .3333 Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Page 152
Type B #10 x 3/4” z.p. VW10A08 Flat Washer 1/4” x 1/16 M0019 Petro Canada OG2 Grease .0300 QP23-0735 PCB Support QDF7908 Black Plug 1” #SQR-1-10-14 QDF299X Adhesive Neoprene 1/4 x 3/4 .3333 Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Control Panel without nurse Call (for reference only: ol230199, rev. 01) Item Part no. Part name Qty. QPCE1207 Diameter 5/8”-18 unc ga 16-18 Cap QDF23-0392 Left Membrane without Nurse Call QDF23-0393 Right Membrane without Nurse Call Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Part name Qty. QDF23-0396 Foot/Head Membrane with Nurse Call QDF23-0397 Head/Foot Membrane with Nurse Call VW10C162402 Nylon Washer 0,505” Ins. Dia. x 3/4” OU VW60C122408 Shoulder Spacer 3/8” Ins. Dia. Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
0.505” ins. x 3/4” out. x 1/16” wi. QDF9012 Connection Terminal (6x2) VV83A9E12 Tapping Screw Type B Pan Head Phillips #8 x 3/8” z.p. QDF23-0530 1/4 Normally Open (N.O.) Phono Plug Cable Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
0.505” ins. x 3/4” out. x 1/16” wi QDF9012 Connection Terminal (6x2) VV83A9E12 Tapping Screw Type B Pan Head Phillips #8 x 3/8” z.p. QDF23-0531 1/4 Normally Closed (N.C.) Phono Plug Cable Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Post Set (for reference only: l23-005g, rev. 05) Item Part no. Part name Qty. 23-0124G Post VV33A1N24-S Machine Screw Pan Head 1/4-20 x 3/4” Scotch Grip QPPF1521 Metal Washer 1/4” Diameter QPPF1514-1 White Plastic Cap Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
QE14376-T Sticker - Headboard Installation VV23A1G32HL Tapping Screw Pan Phillips Type High-Low #10 x 1” z.p. QPAG1801 Rod Support VV27A9G16 Tapping Screw Truss Head Phillips #10 x 1/2” LG Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
QE14376-T Sticker - Headboard Installation VV23A1G32HL Tapping Screw Pan Phillips Type High-Low #10 x 1” z.p. QPAG1801 Rod Support VV27A9G16 Tapping Screw Truss Head Phillips #10 x 1/2” LG Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 161
Part Colors Part number Code QP23-0472 QP23-0473 QP23-0474 QP23-0475...
Phillips #10 x 1” z.p. VV33A1E24 Machine Screw Round Head Phillips 3-32 x 3/4 VV27A9G16 Tapping Screw Truss Head Phillips #10 x 1/2” LG VW11A9E Flat Washer #8 VW60C081005 Sleeve QPAG1801 Rod Support Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Inner Right Handle QP23-0475 Inner Left Handle VV23A1G32HL Tapping Screw Pan Phillips Type High-Low #10 x 1” z.p. VV27A9G16 Tapping Screw Truss Head Phillips #10 x 1/2” LG QPAG1801 Rod Support Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Page 164
Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 165
Part Colors Part number Code QP23-0472 QP23-0473 QP23-0474 QP23-0475...
VV27A9G16 Tapping Screw Truss Phillips Type A #10 x 1/2” z.p. VV33A1E24 Machine Screw Pan Phillips #8-32 x 3/4” z.p. VW11A9E Flat Washer #8 VW60C081005 Sleeve QPAG1801 Rod Support Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 167
Part Colors Part number Code QP23-0472 QP23-0473 QP23-0474 QP23-0475...
Outer Right Handle QP23-0474 Inner Right Handle QP23-0473 Outer Left Handle QP23-0475 Inner Left Handle VV23A1G32HL Tapping Screw Pan Phillips Type High-Low #10 x 1” z.p. QPAG1801 Rod Support Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Removable Two-Sided, Two-Function Pendant Control FA64160 See pg. 175 P&D Two-Function Pendant Control FA64155 See pg. 176 Half an Inch Diameter Stryker Removable I.V. Pole FA64135 See pg. 177 Half-Length Siderail Protective Pads DM64232 See pg. 178 Full-Length Siderail Protective Pads DM64176 See pg.
2111A Tightening Sleeve-Anodized 2109 Compression Socket 2107A Top Tube-Anodized 2105A Bottom Tube-Anodized QE14399-T Manufacturer’s Nameplate QPCE1206 Rubber Cap #000 Black (1/2” x 11/32” x 7/8”) QE71-0246-T “Warning” Sticker Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Bed extender - fa64152 Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Page 172
Tapping Screw Pan Phillips Type B #10 x 3/4” z.p. VW11A9E Flat Washer #8 QE71-0787-T Sticker - Emergency Crank Warning 1 QE14399-T Manufacturer’s Nameplate VE20A1N Hexagone Locknut 1/4-20 z.p. Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 173
DM64063 Cushion for Bed Extender Cushion for Bed extender - dM64064 Cushion for Bed extender (for reference only: dM64064) Item Part no. description DM64064 Cushion for Bed Extender Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Petro Canada OG2 Grease 0.0002 kg QPN-9438 Black Nylon Handle QRC16887 Compression Spring VG10B0424 Spring Pin 1/8” x 3/4” VR43A9439 Shoulder Rivet QE71-0814 Sticker - Emergency Crank QE14399-T Manufacturer’s Nameplate Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Two-Sided, Two function Pendant Control - fa64160 removable Two-Sided, Two function Pendant Control (for reference only: fa64160) Item Part no. description QDF64-0986 Removable Two-Function Pendant Control Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
P&d Two-function Pendant Control (for reference only: fa64155) Item Part no. description QDF64-0687 P&D Two-Function Pendant Control 1 QE71-0133 Stryker Label QDF8066 Security Clip (Interlock Press) 6400-035G Hook of the Pendant Control Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Inch diameter Stryker removable I.v. Pole - fa64135 half an Inch diameter Stryker removable I.v. Pole (for reference only: fa64135) Item Part no. description QDF9165 Stryker’s 1/2” Diameter Removable I.V. Pole Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
S.A. Top Rod 61-0002A S.A. Bottom Tube QPCE1206 Rubber Cap #000 (1/2” x 11/32” x 7/8”) Black QE71-0246-T Warning Sticker QE14399-T Manufacturer’s Nameplate VG10B0630 Spring Pin 3/16” Diameter x 15/16” 1 Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Upright oxygen Bottle holder (for reference only: fa64117) Item Part no. description Qty. QE14399-T Manufacturer’s Nameplate QE71-0601 Sticker - Maximum Load VR11H42 Pop Rivet #42 Dome Head QDF64-1005 Oxygen Support Bottle 64-0647 S.A. Security Chain Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 183
Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Trapeze - fa64145 Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 185
0.062” x 1” ins. x 1.563” out. VW20A10 Spring Washer 5/16” Diameter VR11H46 Pop Rivet #46, Dome Head 64-0536 Chain for Trapeze QDF7871 QR Hitch Pin QE14399-T Manufacturer’s Nameplate QE71-1163-T Storage of the Triangle Sticker Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Qty. 64-0745G S.A. Tray Support QDF5093 Tray and Fasteners QE14399-T Manufacturer’s Nameplate QE71-0578 Sticker - Maximum Load Capacity QE71-0579-F Sticker - Tied Up Load QE71-0580-F Sticker - Caution Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Passport assembly Part number: ol230229g Item recycling/Material Code Control Board (QDF23-0315) Return To Table of Contents 72-1048E MM FL23SE REV A www.stryker.com...
Page 189
QDF8066-ISR 120V Power Cord and Israel Plug (OL250068) QDF8066-ITA 120V Power Cord and Italy Plug (OL250069) QDF8066-ARG 120V Power Cord and Argentina Plug (OL250073) QDF8066-CHI 120V Power Cord and China Plug (OL250074) Return To Table of Contents www.stryker.com 72-1048E MM FL23SE REV A...
Stryker Medical Division, a division of Stryker Corporation, warrants to the original purchaser the Electrical MedSurg Bed, model FL23SE, to be free from defects in material and workmanship for a period of one (1) year after date of delivery. Stryker’s obligation under this warranty is expressly limited to supplying replacement parts and labor for, or replacing, at its option, any product which is, in the sole discretion of Stryker, found to be defective.
Stryker authorized parts used Service during regular business hours (8−5) * Does not include maintenance due to abuse or for any disposable items. Stryker reserves the right to change options without notice. Stryker Medical also offers personalized service contracts. Pricing is determined by age, location, model and condition of product.
Page 193
Stryker France Stryker France ZAC Satolas Green Pusignan ZAC Satolas Green Pusignan Av. De Satolas Green Av. De Satolas Green 69881 MEYZIEU Cedex 69881 MEYZIEU Cedex France France 2008/08 2006/XX 72-1048E MM FL23SE REV A XXXX-XXX-XXX REV X www.stryker.com www.stryker.com...
Need help?
Do you have a question about the FL23SE and is the answer not in the manual?
Questions and answers