Related Manuals for Procopi ProSwell Weva octo 440
Summary of Contents for Procopi ProSwell Weva octo 440
- Page 1 OCTO / OCTO + Installation instructions To be read carefully and kept for future reference PROCOPI Les Landes d’Apigné B.P.45328 35650 LE RHEU Cedex Installation instructions Weva Octo, Octo+ 07/2015 FRANCE GB - Revision: D - Code : 97149997...
- Page 2 (knots, cracks, fl ashes) properties of the wood. For further information, please are entirely acceptable. refer to Procopi’s guarantees concerning the types of wood and their treatment. CAUTION storage. If you do not intend to assemble your pool immediately, you should store it without opening it in a well- ventilated room, or failing this, in an area protected from humidity and sunlight.
-
Page 3: Table Of Contents
» INSTALLATION INSTRUCTIONS / OCTO & OCTO+ CONTENTS > > Foreword ................p-4 Storage & time required for assembly .........p-4 Siting and preparation of the ground for Octo & Octo + pools .............p.5-6 Assembly of the Octo pool structure ........p.7-9 Assembly of the Octo+ pool structure ......p.10-14 Gaskets, laying and cutting out the liner ....p.15-17 Assembling coping on Octo pools ........ -
Page 4: Foreword
» INSTALLATION INSTRUCTIONS / OCTO & OCTO+ FOREWORD > > Congratulations on acquiring your pool. We have taken great care with the design and manufacture of your pool to provide you with a top quality product. The wood used to make the various elements (interlocking walls, coping, ladder, etc.) was carefully selected. Outdoors, these wooden elements are subject to constant weathering: contact with the ground, temperature variations, exposure to sunlight, rain and frost, insect attack, etc. -
Page 5: Siting And Preparation Of The Ground For Octo & Octo+ Pools
» INSTALLATION INSTRUCTIONS / OCTO & OCTO+ SITING AND PREPARATION OF THE GROUND FOR > > OCTO & OCTO+ POOLS This is the most important step in the procedure as the pool site will determine the service life of your pool. There are some rules that must be respected. - Page 6 » INSTALLATION INSTRUCTIONS / OCTO & OCTO+ OCTO+ POOLS > > (ABOVE GROUND CONFIGURATION ONLY. ADVISE AND INSTRUCTIONS FOR IN-GROUND OR PARTIALLY SUNKEN CONFIGURATIONS ARE ILLUSTRATED AT THE END OF THIS DOCUMENT). Trace out site of the pool and clear the ground of plants, grass and other miscellaneous objects. Next, level and smooth the surface using a spade, rake and a pickaxe (if necessary).
-
Page 7: Assembly Of The Octo Pool Structure
» INSTALLATION INSTRUCTIONS / OCTO & OCTO+ ASSEMBLY OF THE OCTO POOL STRUCTURE > > - Before you begin, familiarise yourself with the nomenclature enclosed in the “Accessories” kit and the exploded view (at the end of this notice) that corresponds to your pool. - Page 8 » INSTALLATION INSTRUCTIONS / OCTO & OCTO+ ASSEMBLY OF THE OCTO POOL STRUCTURE (contd.) > > The wooden brackets will support the coping that will be The are 3 wooden brackets per side (except the side mounted after the pool is filled. Pre-drill the wall from holding the skimmer).
- Page 9 » INSTALLATION INSTRUCTIONS / OCTO & OCTO+ ASSEMBLY OF THE OCTO POOL STRUCTURE (contd.) > > Mount a corner junction piece (junction+corner blister pack) in each corner using 2 SS screws (bag E) inserted through the notches intended for this purpose. Make sure that these parts are flush with the top of the pool wall. Each wall will take a 1.18 m length of track and an additional length that will need to be trimmed to size.
-
Page 10: Assembly Of The Octo Pool Structure
» INSTALLATION INSTRUCTIONS / OCTO & OCTO+ ASSEMBLY OF THE OCTO+ POOL STRUCTURE > > The pool structure is mounted in two stages: - Stage 1, excavation of the site and installation of the cradles designed to reinforce the lateral walls. A cradle comprises a cross beam, vertical posts and oss section of the cement slab metallic plates to be bolted together. -
Page 11: Assembly Of The Octo+ Pool Structure
» INSTALLATION INSTRUCTIONS / OCTO & OCTO+ ASSEMBLY OF THE OCTO+ POOL STRUCTURE (CONTD.) > > Recommendations and advice: - Before beginning assembly, identify the various slat types with reference to the exploded view at the end of this document. - Establish the fi nal orientation of your pool, the skimmer should be oriented facing into prevailing winds. - Page 12 » INSTALLATION INSTRUCTIONS / OCTO & OCTO+ ASSEMBLY OF THE OCTO+ POOL STRUCTURE (contd.) > > At this point, fit the filtration system into the machined slat (F). Slot the top skimmer slat (G) over slat F and continue around the pool, fitting 2 type H slats, 1 type l slat and 4 type J half-slats into position as shown. Attach a decorative trim (type K) to the end of each wall Working from the outside, screw the metallic posts using 4 3.1x75 mm screws (bag L) inserted through holes...
- Page 13 » INSTALLATION INSTRUCTIONS / OCTO & OCTO+ ASSEMBLY OF THE OCTO+ POOL STRUCTURE (contd.) > > L 460 Attach the wooden brackets along the lengths as shown. Skimmer Filtration unit +460 60 cm +540 50 cm +640 75 cm +840 On the wall holding the skimmer, position 1 coping Mount an anchoring plate (coping support bracket kit) on support bracket on either side of the skimmer equidistant...
- Page 14 » INSTALLATION INSTRUCTIONS / OCTO & OCTO+ ASSEMBLY OF THE OCTO+ POOL STRUCTURE (contd.) > > Octo +540 pools - fitting the liner locking rails (with junction strips) Octo +460 pools - fitting the liner locking rails (with junction strips) (to be trimmed) (to be trimmed) Octo +640 pools - fitting the liner locking rails (with junction strips)
- Page 15 » INSTALLATION INSTRUCTIONS / OCTO & OCTO+ GASKETS FOR POOL FITTINGS > > From the pool side, insert return fitting throughwall flange Before fitting the liner, glue one of the 2 rectangular (pool fitting pack) into the opening in the pierced slats. Fix self-adhesive gaskets (pool fitting skin pack) around the it in position using countersunk self-tapping 3x25 screws.
- Page 16 » INSTALLATION INSTRUCTIONS / OCTO & OCTO+ FITTING & CUTTING OUT THE LINER (contd.) > > Once the liner has been hung and is correctly positioned, fill the pool with 2 cm of water. Push any creases towards the walls smoothing out the liner as much as possible. This operation will not be possible if the pool is empty or overfilled (contains more than 2 cm of water).
- Page 17 » INSTALLATION INSTRUCTIONS / OCTO & OCTO+ Glue the second skimmer gasket to the interior surface of the skimmer or filtration unit flange. Locate the 4 corner holes of the mouth and mark them with a pen. Position the flange such that its corner holes are aligned with the points marked in pen. Use a small screw driver or punch to pierce the liner at the 4 points marked and fix the flange in position with the gasket against the liner.
- Page 18 » INSTALLATION INSTRUCTIONS / OCTO & OCTO+ FITTING THE COPING ON OCTO POOLS > > The coping comprises 8 interior planks and 8 exterior planks. Arrange the planks on the the support brackets as shown. The interior planks overlap the pool by approximately 25 mm from the edge of the wall. Make sure that the elements are correctly positionned around the periphery of the pool.
- Page 19 » INSTALLATION INSTRUCTIONS / OCTO & OCTO+ FITTING THE COPING ON OCTO+ POOLS > > Filtration unit between A or B A’ or B’ C’ E’ A & B 1550 1677 1905 2029 +460 1377 1429 1254 1378 +540 1677 1739 1254 1378...
- Page 20 » INSTALLATION INSTRUCTIONS / OCTO & OCTO+ ASSEMBLING AND INSTALLING THE STAINLESS STEEL LADDER > > seal escutcheon plate screwed flange Assemble the various parts of the ladder referring to the Position the ladder in the pool on the coping module of installation instructions provided.
- Page 21 » INSTALLATION INSTRUCTIONS / OCTO & OCTO+ ASSEMBLING AND POSITIONING THE WOODEN LADDER (contd.) > > The wooden ladder is fitted with two lever latches that lock it into position. The lever sections are fitted to the ladder supports and the hooks are mounted under the coping (these parts are enclosed in bag K). Observe how these 2 parts interact together to understand how the mechanism works and establish the travel necessary for the ladder to be locked correctly into position.
- Page 22 » INSTALLATION INSTRUCTIONS / OCTO & OCTO+ INSTALLATION OF PARTIALLY IN-GROUND OR IN-GROUND > > POOLS CAUTION: This type of configuration must be protected by one of the four safety systems that comply with French safety standards concerning safety of in-ground pools; safety barrier, alarm, safety cover or a shelter. The decree no.
- Page 23 » INSTALLATION INSTRUCTIONS / OCTO & OCTO+ OCTO POOLS > > For selection of the site, refer to the instructions at the beginning of this document. Once the excavation is at the required depth, make sure that the surface is perfectly flat and level. Next, dig a trench to allow drainage under the walls of the pool.
- Page 24 » INSTALLATION INSTRUCTIONS / OCTO & OCTO+ FOR OCTO+ POOLS >> For selection of the site, refer to the instructions at the beginning of this document. Once the excavation is at the required depth, make sure that the surface is perfectly flat and level. Next, dig a trench to allow drainage under the walls of the pool.
- Page 25 » INSTALLATION INSTRUCTIONS / OCTO & OCTO+ MAINTENANCE & OPERATION > > Wood is a living material that responds to changes in temperature and humidity; cracks and splits may appear; this is natural and in no way impacts the service life of our products. The wooden components of this pool are subjected to a Class IV autoclave treatment that complies with standards in effect, they present no danger to people or animals that may come into direct contact with the wood.
- Page 26 » INSTALLATION INSTRUCTIONS / OCTO & OCTO+ MAINTENANCE & OPERATION (contd.) > > ACCESSORIES Electrical equipment such as underwater lights that require an electrical supply must be fitted and wired in according to the standards in effect. We recommend that you take great care in this matter and that you call on the services of qualified specialists.
-
Page 27: Safety
» INSTALLATION INSTRUCTIONS / OCTO & OCTO+ SAFETY > > DO NOT PLAY WITH SAFETY ! ! ! In this fun environment you need to watch your children! You alone are responsible for their safety ! Children should be closely supervised at all times. The risk is at its greatest when children are less than 5 years old. - Page 28 - Folds that remain despite following all the instructions regarding fitting of the liner should be reported immediately to your Procopi agent. The appearance of yellow stains or discolouration along the water line.
-
Page 29: Guarantee
» INSTALLATION INSTRUCTIONS / OCTO & OCTO+ GUARANTEES (contd) > > ARTICLE Subject and scope of the Term of the guarantee as of Conditions governing acceptance of a claim guarantee the date of purchase POOL Leaktightness and durability 10 years FITTINGS of the pool fittings ARTICLE... - Page 30 » INSTALLATION INSTRUCTIONS / OCTO & OCTO+ EXPLODED VIEW OF THE OCTO+ STRUCTURE > > (AUTONOMOUS FILTRATION UNIT) proswell.fr...
- Page 31 » INSTALLATION INSTRUCTIONS / OCTO & OCTO+ EXPLODED VIEW OF THE OCTO STRUCTURE > > (SKIMMER) Rail PVC support bracket proswell.fr...
- Page 32 » » INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS / OCTO & OCTO+ / OCTO & OCTO+ QUALITY CERTIFICATE PEFC CONTROL CHAIN Company Control chain no. The chain of custody of the company designated hereinover complies with the PEFC* stipulations in effect. This certifi cate was issued in accordance with the PEFC reference governing chain of custody of wood, FCBA MQ CERT 11-360.