Routing The Power Harness. Cab000219 (4Pin Nitro™)) Or (Cab000262 (6Pin Nitro-X™); Routing The Sensor Harness Cab000218; Power Connections (Cab000211 Connects To Cab000205/6); Nitro™ 400 With Cables - Gatekeeper NiTRO 401 User Manual

APPENDIX APPENDIX APPENDIX APPENDIX

Power Connections (CAB000211 connects to CAB000205/6)

Power Connections (CAB000211 connects to CAB000205/6) Power Connections (CAB000211 connects to CAB000205/6) Power Connections (CAB000211 connects to CAB000205/6)
Please Note: This section only relates to units shipped and containing CAB000205/206;
CAB000211 and CAB000145 Sensor/Trigger cable, prior to December 2011.
NiTRO™ ™ ™ ™ 400 With Cables.
NiTRO 400 With Cables.
NiTRO NiTRO 400 With Cables. 400 With Cables.
Figure 40: 3 Camera Connection.
ITEM # ITEM # ITEM # ITEM # DESCRIPTION DESCRIPTION DESCRIPTION DESCRIPTION
1 POWER SENSOR ADAPTER CABLE
2 VIDEO OUT CABLE
3 POWER SENSOR ADAPTER CABLE W/GPS
4 GPS MODULE W/15' CABLE
5 EXTERNAL TRIGGER CABLE
6 POWER CABLE AND FUSE
7 CAMERA CABLE 15', 30' OR 60'
8 VIDEO ADAPTER CABLE 1 CHANNEL
9 VIDEO ADAPTER CABLE 2 CHANNEL
PART NUMBER PART NUMBER PART NUMBER PART NUMBER
CAB000205
GSX-N40X/VIDEO/AUDIO OUT
ASSY
CAB000206
DVRGPSN40X_ASSY
CAB000145
CAB000211
CAB000142 or
GSWHC2N-XX
CAB000209
CAB000202
- 52 -
Leave enough cable slack at the Rear of the mounting bracket,12 inches.
Check For
Safety
Not blocking passenger or driver access.
Not obstructing driver's view.
Will not snag loose clothing or carry-on items.
Accessibility.
To the DVR front panel for configuring.
For easy SD card removal and insertion.
For easy harness routing and connecting.
219 (4pin NiTRO™ ™ ™ ™ )) )) )) )) or or or or ( ( ( ( CAB000
Routing the Power Harness. CAB000 Routing the Power Harness. CAB000219 (4pin NiTRO
Routing the Power Harness. Routing the Power Harness. CAB000 CAB000 219 (4pin NiTRO 219 (4pin NiTRO
(6pin NiTRO- - - - X X X X ™ ™ ™ ™ ) ) ) )
(6pin NiTRO (6pin NiTRO (6pin NiTRO
Always use grommets when running the harness through sheet metal holes.
Avoid excessively tight bends especially around metal surfaces.
Use fuse holder and fuse provided on the 12V+ connection.
Connect fuse as close to power source as possible.
Use cable ties to secure harness and fuse holder.
Cut power harness to length, removing excess cable.
Use correct terminal size for wire gauge. Always use Butt or Ring Terminal
connectors.
10-12 AWG = Yellow
14-16 AWG = Blue
18-22 AWG = Red
Use ratcheting crimpers for terminal installation.
If grounding to a painted surface, scrape off paint and use 'star' washer between terminal
and metal surface.
DO NOT use painted or anodized fasteners.
Before connecting constant power, cut off excess slack.
Before connecting power directly at battery, verify that the system maintains a minimum of
8Volts during engine cranking. Testing requires starting the bus, with a multi-meter
connected to battery. Confirm voltage does not drop below 8V during cranking. If voltage
drops, advise mechanic at bus garage that the batteries may need to be replaced or a
Gatekeeper Systems PowerVault B maybe needed.

Routing the Sensor Harness CAB000218

Routing the Sensor Harness Routing the Sensor Harness Routing the Sensor Harness CAB000218. . . . CAB000218 CAB000218
Route the TRIGGERS harness to the electrical panel.
Connect Orange lead to stop arm circuit
Connect Blue lead to warning lights circuit
Always use grommets when running the harness through sheet metal holes.
Avoid excessively tight bends especially around metal surfaces.
CAB000262 262
CAB000 CAB000 262 262
- 17 -