Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Gatekeeper NiTRO 401
Summary of Contents for Gatekeeper NiTRO 401
- Page 1 Safety, Security, Peace of Mind™ Covering Gatekeeper Systems NiTRO™ 401; NiTRO™ 404 Digital Video Recorders NiTRO-X™ 404 Digital Video Recorder Software Version: 1123-S5R16/1 - 1 - NiTRO-X™ 400 series/NiTRO™ 400 Series User Guide. DN2431. V1.6...
-
Page 2: Table Of Contents
Table of Contents. Tables.......................................... 4 Introduction ......................................... 6 Glossary. Important Safeguards and Warnings................................7 Product Overview: NiTRO™ 400 Series..............................8 Product Overview: NiTRO-X™ 400 Series..............................9 NiTRO™ and NiTRO-X™ Comparison Chart. Available Download Kits. Installation......................................... 12 Mounting Installation Instructions. Power Connections. - Page 3 Language Time Zone Contact Information. Contact Information. Contact Information. Contact Information. Date/Time System Info Config Setup App Restart O/S Reboot Network. Port Network Type IP Address GSI – – – – Canada Canada Canada Canada Storage. 301-31127 Wheel Avenue Overwrite Abbotsford, BC V2T 6H1 Format Canada...
-
Page 4: Tables
Operating Manual. This warranty does not apply to GSX Retrofit to NiTRO™ or NiTRO-X™ any damage to the Gatekeeper Systems product that is This warranty gives you specific legal rights, and you Dome Camera (CAMICAGSC) Installation and Configuration......................60... - Page 5 FIGURE 11 : DEFAULT RECORD SETTINGS............................31 Gatekeeper Systems and found in the reasonable FIGURE 12 : ESTIMATED RECORD TIME............................. 32 judgment of Gatekeeper Systems to be defective in The warranty does not extend to repairs made FIGURE 13 : SCHEDULED RECORDING............................... 32...
-
Page 6: Introduction
Glossary..Glossary Glossary • Report any defective product to the school district and/or Gatekeeper Systems Digital Video Recorder; A DVR functions similarly to a VCR, except it for direction. uses a disk to record, as opposed to video-tapes. -
Page 7: Important Safeguards And Warnings
CAB000268, 4 pin to 6 pin Power Adapter Cable MUST be utilized (See Appendix for more information). If at any time there is a question about how to proceed, contact Gatekeeper Systems Inc. at 1-888-666-4833 or 604-864-6187 immediately for directions. Review all installation documentation, including technical bulletins. -
Page 8: Product Overview: Nitro™ 400 Series
NiTRO-X™ Control Unit and the SD Card for each bus for future reference. Ensure all system Connect camera harness input to camera. components are accounted for prior to installation. Contact Gatekeeper Systems, Inc. if any Tuck attached camera harness behind the camera circuitry and then mount base to the components are missing or if they appear defective. -
Page 9: Product Overview: Nitro-X™ 400 Series
: NiTRO- - - - X X X X ™ ™ ™ ™ 400 Series. Dome Camera (CAMICAGSC) Installation and Configuration. Dome Camera (CAMICAGSC) Installation and Configuration. Dome Camera (CAMICAGSC) Installation and Configuration. Dome Camera (CAMICAGSC) Installation and Configuration. Product Overview Product Overview: NiTRO 400 Series. -
Page 10: Available Download Kits
NiTRO™ ™ ™ ™ and NiTRO and NiTRO- - - - X X X X ™ ™ ™ ™ Comparis GSX Retrofit to NiTRO™ ™ ™ ™ or NiT RO- - - - X X X X ™ ™ ™ ™ NiTRO NiTRO NiTRO... - Page 11 400 software & documents The CD contains the MAXVIEW 400 software, softcopy of NiTRO 400 Series User Manual, a Read Me file and NiTRO Existing Gatekeeper VCR Installations. Existing Gatekeeper VCR Installations Firmware Upgrade Procedure. Existing Gatekeeper VCR Installations Existing Gatekeeper VCR Installations Disconnect the VCR power cable (16 AWG White wire and Black wire) from the battery.
-
Page 12: Mounting Installation Instructions
Retrofitting GSX / VCR Systems to NiTRO™ ™ ™ ™ and NiTRO and NiTRO- - - - X X X X ™ ™ ™ ™ Systems. Installation Installation..Installation Installation Retrofitting GSX / VCR Systems to NiTRO Retrofitting GSX / VCR Systems to NiTRO Retrofitting GSX / VCR Systems to NiTRO and NiTRO... - Page 13 Figure 1 Definitions Figure 1 Definitions Figure 1 Definitions Figure 1 Definitions. fitting NiTRO™ ™ ™ ™ 900 and 000 to NiTRO™ ™ ™ ™ 400 and NiTRO- - - - X X X X ™ ™ ™ ™ 400 Retro Retrofitting NiTRO Retro...
-
Page 14: Alarm Button Mounting
• OTHER OTHER OTHER OTHER Mount Alarm button in drivers switch panel. • CONFIGURATIONS CONFIGURATIONS CONFIGURATIONS CONFIGURATIONS..CAMERA ADAPTER CABLES CAMERA ADAPTER CABLES CAMERA ADAPTER CABLES CAMERA ADAPTER CABLES..Ensure SD card is installed in DVR control unit prior to turning on the system. •... -
Page 15: Recommended Location For Alarm Button
CAB000145: 7 Wire; 4 Wire and 3 Wire Terminations. CAB000145: 7 Wire; 4 Wire and 3 Wire Terminations. CAB000145: 7 Wire; 4 Wire and 3 Wire Terminations. CAB000145: 7 Wire; 4 Wire and 3 Wire Terminations. CAB00262 (6 PIN) NiTRO-X™ DVR Power Cable (30 feet long). -
Page 16: Suggested System Locations
Power Sensor Connection; NiTRO™ ™ ™ ™ Pre The table below indicates the wiring for CAB000218 shown in Figure 2. Power Sensor Connection; NiTRO Pre- - - - December December 2011. 2011. Power Sensor Connection; NiTRO Power Sensor Connection; NiTRO December December 2011. -
Page 17: Routing The Power Harness. Cab000219 (4Pin Nitro™)) Or (Cab000262 (6Pin Nitro-X™)
ASSY drops, advise mechanic at bus garage that the batteries may need to be replaced or a POWER SENSOR ADAPTER CABLE W/GPS CAB000206 Gatekeeper Systems PowerVault B maybe needed. GPS MODULE W/15’ CABLE DVRGPSN40X_ASSY Routing the Sensor Harness Routing the Sensor Harness... -
Page 18: Connecting Cameras
Connecting Cameras. Connecting Cameras. Connecting Cameras. Connecting Cameras. The process to send a captured video clip is very similar, mark your clip in MaxVIEW™ 400 first and then choose Video Clip. This process can take several minutes depending upon your system and its settings, etc. -
Page 19: Camera Mounting And Connections
The S2 series camera balls support in-field lens changing. The S1 series Do Not support in- MaxVIEW 400. This will create the image field lens changing. Please contact Gatekeeper Systems on 888-666-4833 for options and which you are now going to send. pricing for S1 series camera lenses. -
Page 20: Saving A Clip
A. A. A. A. Rubber G Rubber Gasket asket. B. . B. Base Plate Base Plate. C. . C. Camera Ball Camera Ball..Rubber G Rubber G asket asket . B. . B. Base Plate Base Plate . -
Page 21: S205 Camera Lens Changing
MaxVIEW™ 400 supports three modes of deinterlacing; Off (Default); Forced and Automatic. this cabling. • OFF: Default value and should only be altered if directed by a Gatekeeper Systems technical support representative. With the two halves of the camera laid carefully •... -
Page 22: Suggested Camera Locations
Suggested Camera Locations. Suggested Camera Locations. Suggested Camera Locations. Suggested Camera Locations. Using The Calendar Feature. Using The Calendar Feature. Using The Calendar Feature. Using The Calendar Feature. It is recommended that MaxVIEW™ be run utilizing Calendar View as this will reduce the amount of time required to load the video ready for playback. -
Page 23: Video Alignment Cable: Cab000157
Using The GPS Zoom Feature. Using The GPS Zoom Feature. Using The GPS Zoom Feature. Using The GPS Zoom Feature. Video Alignment Cable: CAB000157 Video Alignment Cable: CAB000157 Video Alignment Cable: CAB000157 Video Alignment Cable: CAB000157 When viewing the Vehicle Locator if you wish to The following information explains the correct use of the Video Alignment Cable CAB000157. -
Page 24: Gps Mapping Options
A: A: A: A: Portable LCD or DVD C: C: C: C: Camera B: B: B: B: NiTRO™ or NiTRO-X™ GPS. GPS. GPS. GPS. D: D: D: D: GSWHC2N-XX Camera Harness, 15’; 30’ or 60’ lengths. Please note: Only NiTRO ™ 400 or NiTRO-X ™ 400 series systems which have a GPS module Please note: Please note: Please note:... -
Page 25: System Features
MaxVIEW™ ™ ™ ™ 400 Components. MaxVIEW 400 Components. System Features. System Features. System Features. System Features. MaxVIEW MaxVIEW 400 Components. 400 Components. 1. Standard Windows Menu iTRO- - - - X X X X ™ ™ ™ ™ 400 Series N N N N iTRO iTRO iTRO... -
Page 26: Table 5: Nitro-X™ Power And Run Led Definition
POWER Extend). Ignition is OFF and MaxVIEW™ ™ ™ ™ 400 Operation. MaxVIEW MaxVIEW MaxVIEW 400 Operation. 400 Operation. 400 Operation. NiTRO™ or NiTRO-X™ is recording. The DVR will Opening a File. Opening a File. Opening a File. Opening a File. power down when Power Off Delay (Record Extend) is When viewing files directly from an SD Card... -
Page 27: Nitro-X™ 400 Rear View
iTRO- - - - X X X X ™ ™ ™ ™ 400 Retrieving Captured Data. Retrieving Captured Data. Retrieving Captured Data. Retrieving Captured Data. N N N N iTRO 400 Rear View. Rear View. iTRO iTRO Rear View. Rear View. The image in Figure 6 is viewed from directly behind the NiTRO-X™... -
Page 28: Remote Control And Menu System
The next window will ask for the destination of the Audio Toggle Key files. It is recommended that the default location, Direction Navigational Keys (C:\Program Files\Gatekeeper 10. Menu. Press to enter menus; sub- Systems\MaxVIEW 400), is accepted, Click Next. menus and to make selections from available options. -
Page 29: Quick Configuration Menu System
MaxVIEW™ 400 is designed to be used with the NiTRO™ 400 or NiTRO-X™ 400 series The live menu is divided into six configurable sections. of digital Video Recorders and is available as a free download from www.gatekeeper- systems.com or a printed version can be purchased as part of the Basic Kit (P/N: GSX- Determines if camera information;... -
Page 30: Video Adjustment
Options: (All in seconds) 2, 4, 8,16, 32, 52 or Off. Default Value: Default Value: Default Value: Default Value: On LANC LANC LANC LANC This Mode is reserved for future development. Default Value: Default Value: Default Value: Default Value: OFF Function Function Function... -
Page 31: Record
numbers and once completed highlight the OK button and then press OK on Record. Record. Record. Record. the remote control. Default Value: Default Value: Default Value: Default Value: 100 Mile/Hr 100 Mile/Hr 100 Mile/Hr 100 Mile/Hr The Record menu is divided into six sections. Record Settings Record Settings Record Settings... -
Page 32: File Length
Figure 16: Alarm Action Defaults. The column TIP contains the information which appears both on the OSD and within MaxVIEW™. To change the title of any or all three items highlight the required TIP and then press the menu button on the remote control this will bring up a text dialog box, Enter the descriptions as required and Press OK when completed. -
Page 33: New Password
Total Total Total Total Displays the total capacity of the currently installed SD card. This total is in Format Format Format Format Use the Menu key to access options and the Up or Down navigation key to Capacity Capacity Capacity Capacity decimal and so will not reflect the Bytes capacity. - Page 34 ( ( ( ( This should This should This should only be done when directed by This should only be done when directed by only be done when directed by Gatekeeper Systems only be done when directed by Gatekeeper Systems Gatekeeper Systems Gatekeeper Systems...