Siemens Micromaster 440 Operating Instructions Manual page 78

5 System parameters
Par. No.
P2019[8]
r2025[2]
r2026[2]
r2027[2]
r2028[2]
r2029[2]
r2030[2]
r2032
r2031[2]
r2033
r2036
r2037
P2040
P2041[5]
r2050[8]
r2053[5]
P2051[8]
r2054[7]
r2090
r2091
Alarms, Warnings and Monitoring (P0004 = 21)
Par. No.
r0947[8]
r0948[12]
r0949[8]
P0952
P2100[3]
P2101[3]
r2110[4]
P2111
r2114[2]
P2115[3]
P2150[3]
P2151[3]
P2152[3]
P2153[3]
P2155[3]
P2156[3]
P2157[3]
P2158[3]
P2159[3]
P2160[3]
P2161[3]
P2162[3]
78
Parametername
CI: PZD to COM link (USS)
USS rejected telegrams
USS character frame error
USS overrun error
USS parity error
USS start not identified
USS BCC error
BO: CtrlWrd1 from BOP link (USS)
USS length error
BO: CtrlWrd2 from BOP link (USS)
BO: CtrlWrd1 from COM link (USS)
BO: CtrlWrd2 from COM link (USS)
CB telegram off time
CB parameter
CO: PZD from CB
CB identification
CI: PZD to CB
CB diagnosis
BO: Control word 1 from CB
BO: Control word 2 from CB
Parametername
Last fault code
Fault time
Fault value
Total number of faults
Alarm number selection
Stop reaction value
Warning number
Total number of warnings
Run time counter
AOP real time clock
Hysteresis frequency f_hys
CI: Monitoring speed setpoint
CI: Act. monitoring speed
Time-constant speed filter
Threshold frequency f_1
Delay time of threshold freq f_1
Threshold frequency f_2
Delay time of threshold freq f_2
Threshold frequency f_3
Delay time of threshold freq f_3
Min. threshold for freq. setp.
Hysteresis freq. for overspeed
Default Level
52:0 3
- 3
- 3
- 3
- 3
- 3
- 3
- 3
- 3
- 3
- 3
- 3
20 3
0 3
- 3
- 3
52:0 3
- 3
- 3
- 3
Default Level
- 2
- 3
- 3
0 3
0 3
0 3
- 2
0 3
- 3
0 3
3.00 3
0:0 3
0:0 3
5 2
30.00 3
10 3
30.00 2
10 2
30.00 2
10 2
3.00 2
20.00 2
MICROMASTER 440 Operating Instructions
6SE6400-5AW00-0BP0
Issue 12/02
DS QC
CT N
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
CT N
CT N
- -
- -
CT N
- -
- -
- -
DS QC
- -
- -
- -
CT N
CT N
CT N
- -
CT N
- -
CT N
CUT N
CUT N
CUT N
CUT N
CUT N
CUT N
CUT N
CUT N
CUT N
CUT N
CUT N
CUT N