Siemens Micromaster 440 Operating Instructions Manual page 76

5 System parameters
Par. No.
P1346[3]
P1350[3]
P1400[3]
r1407
r1438
P1452[3]
P1460[3]
P1462[3]
P1470[3]
P1472[3]
P1477[3]
P1478[3]
r1482
r1490
P1488[3]
P1489[3]
P1492[3]
P1496[3]
P1499[3]
P1500[3]
P1501[3]
P1503[3]
r1508
P1511[3]
r1515
r1518
P1520[3]
P1521[3]
P1522[3]
P1523[3]
r1526
r1527
P1525[3]
P1530[3]
P1531[3]
r1538
r1539
P1570[3]
P1574[3]
P1580[3]
P1582[3]
r1598
P1596[3]
P1610[3]
P1611[3]
76
Parametername
Imax controller integral time
Voltage soft start
Configuration of speed control
CO/BO: Status 2 of motor control
CO: Freq. setpoint to controller
Filter time for act.speed (SLVC)
Gain speed controller
Integral time speed controller
Gain speed controller (SLVC)
Integral time n-ctrl. (SLVC)
BI: Set integrator of n-ctrl.
CI: Set integrator value n-ctrl.
CO: Integral output of n-ctrl.
CO: Droop frequency
Droop input source
Droop scaling
Enable droop
Scaling accel. precontrol
Scaling accel. torque control
Selection of torque setpoint
BI: Change to torque control
CI: Torque setpoint
CO: Torque setpoint
CI: Additional torque setpoint
CO: Additional torque setpoint
CO: Acceleration torque
CO: Upper torque limit
CO: Lower torque limit
CI: Upper torque limit
CI: Lower torque limit
CO: Upper torque limitation
CO: Lower torque limitation
Scaling lower torque limit
Motoring power limitation
Regenerative power limitation
CO: Upper torque limit (total)
CO: Lower torque limit (total)
CO: Fixed value flux setpoint
Dynamic voltage headroom
Efficiency optimization
Smooth time for flux setpoint
CO: Flux setpoint (total)
Int. time field weak. controller
Continuous torque boost (SLVC)
Acc. torque boost (SLVC)
Default Level
0.300 3
0 3
1 3
- 3
- 3
4 3
3.0 2
400 2
3.0 2
400 2
0:0 3
0:0 3
- 3
- 3
0 3
0.05 3
0 3
0.0 3
100.0 3
0 2
0:0 3
0:0 3
- 2
0:0 3
- 2
- 3
5.13 2
-5.13 2
1520:0 3
1521:0 3
- 3
- 3
100.0 3
0.75 2
-0.75 2
- 2
- 2
100.0 2
10 3
0 2
15 3
- 3
50 3
50.0 2
0.0 2
MICROMASTER 440 Operating Instructions
6SE6400-5AW00-0BP0
Issue 12/02
DS QC
CUT N
CUT N
CUT N
- -
- -
CUT N
CUT N
CUT N
CUT N
CUT N
CUT N
UT N
- -
- -
CUT N
CUT N
CUT N
CUT N
CUT N
CT Q
CT N
T N
- -
T N
- -
- -
CUT N
CUT N
T N
T N
- -
- -
CUT N
CUT N
CUT N
- -
- -
CUT N
CUT N
CUT N
CUT N
- -
CUT N
CUT N
CUT N