Listings And Approvals - Notifier NFS2-3030 Operation And Maintenance Manual

Example of Programming
for the ACPS-610 Using 6 Addresses
Example for ACPS-610
Using Canadian Reporting with Two Stage

Listings and Approvals

These listings and approvals apply to the modules specified in
this document. In some cases, certain modules or applications
may not be listed by certain approval agencies, or listing may
be in process. Consult factory for latest listing status.
• UL Listed: S635.
• ULC Listed: S635.
• FM Approved.
• CSFM: 7315-0028:0248,
0028:0243.
• MEA #30-08-E.
• FDNY: COA #6085, #6098.
When used with the MARINE-EQ, appropriate seismic
bracket, and marine approved devices, the ACPS-610(E) is
approved by the following agencies:
• US Coast Guard: 161.002/50/0 (Standard 46 CFR).
• Lloyd's Register: 11/600013 (ENV 3 category).
• American Bureau of Shipping (ABS).
Page 2 of 2 — DN-60244:C3 • 4/23/2012
7165-0028:0224, 7165-
This document is not intended to be used for installation purposes.
We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.
For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.
Product Line Information
ACPS-610: Addressable charger power supply, with selectable
built-in synchronization, and four built-in control modules. Sev-
eral mounting options available (see below).
ACPS-610E: Same as ACPS-610, but configured for 220/240
VAC operation.
CAB-PS1: The CAB-PS1 can house one ACPS-610(E) and
two 12 AH batteries. Dimensions: 15.218" (38.654 cm) high x
14.5" (36.83 cm) wide x 3.562" (9.048 cm) deep with door.
SEISKIT-PS/2/4: Seismic kit for mounting ACPS-610 in a
CAB-PS1. Includes bracket for two 12 AH batteries.
DR-PS1: When installing an ACPS-610(E) into an older ver-
sion of the CAB-PS1 used for an ACPS-2406(E), the new
wider door must be ordered for use with the older version
cabinet.
BB-25: The BB-25 can house one ACPS-610(E) and two 12
volt, 26 AH batteries.
BB-100: The BB-100 can house one ACPS-610(E) and two 12
volt, 55 AH or 100 AH AH batteries.
BB-200: The BB-200 can house one ACPS-610(E) and four
12 volt, 100 AH batteries.
CAB-4 Series: The ACPS-610(E) can mount in any of the
CAB-4 Series cabinets with CHS-PS or CHS-BH . See DN-
6857.
EQ Cabinet Series: The ACPS-610(E) can mount in any of
the EQ Cabinet Series cabinets using CHS-6. See DN-60229.
MARINE-EQ System: Protects equipment in shipboard and
waterfront applications. For a full list of required and optional
equipment, see DN-60688.
CHS-PS/ CHS-6: Chassis used to mount the ACPS-610(E) in
row 1, 2, or 3 of the CAB-4 or EQ series enclosure.
CHS-BH: Battery mounting chassis that holds up to two 12AH
batteries on a CHS-PS.
Batteries: ACPS-610(E) battery charging circuit range is 12 -
200 AH. See DN-6933.
Notifier®, FlashScan®, System Sensor®, and SpectrAlert® are registered
trademarks of Honeywell International Inc. Windows® is a registered
trademark of Microsoft.
©2012 by Honeywell International Inc. All rights reserved. Unauthorized use
of this document is strictly prohibited.
www.notifier.com
Made in the U.S. A.