Paramount Fitness Ultra UV2 Replacement Instructions Manual
Ultimate uv water sanitizer
Hide thumbs
Also See for Ultra UV2:
- Owner's manual (24 pages) ,
- Instruction & operation manual (16 pages) ,
- Replacement instructions manual (8 pages)
Advertisement
Quick Links
Signal Words and Symbols Used In This Manual
This installation guide contains specific precautions and symbols to identify safety-related information. You
will find DANGER, CAUTION, WARNING and NOTICE symbols which require special attention. Please
read them carefully and follow these precautions as indicated! They will explain how to avoid hazards that
may endanger you or persons using or maintaining your pool or spa.
DANGER
avoided, will result in death or serious injury.
CAUTION
could result in minor or moderate injury.
PLEASE REVIEW THE INSTALLATION GUIDE IN ITS ENTIRETY AND HEED ALL SAFETY
INFORMATION. Failure to follow these instructions and warnings can result in DEATH OR SERIOUS
INJURY.
DANGER
When using this electrical equipment, basic safety precautions should always be followed, including the following:
WARNING:
• Follow all applicable electrical codes.
• Turn off power at main source before making any electrical connections or servicing the unit.
• To reduce the risk of electric shock, injury or death disconnect unit from power supply
• Follow the instructions or risk of serious injury or death could occur!
WARNING
eyes and skin. Never look directly at a UV lamp that is connected to a power source. Avoid UV skin
exposure at all times.
295 East Corporate Place • Suite 100 • Chandler, AZ 85225
Toll Free: 1.800.621.5886 • Phone: 480.893.7607 • Fax: 480.753.3397
Paramount@1Paramount.com • www.1Paramount.com
004-027-9909-00
DANGER indicates a
hazardous situation which, if not
CAUTION indicates a hazardous
situation which, if not avoided,
IMPORTANT SAFETY INSTRUCTIONS: READ COMPLETELY
BEFORE PROCEEDING.
UV EXPOSURE & PROTECTION:
UV-A and UV-B radiation can have adverse short and long term effects on the
REV 02
ECN 1710
Ballast Replacement Instructions
WARNING
result in death or serious injury.
NOTICE
Pool, Spa & Pond
Water Sanitizer 4BJ1
Publish date 03/05/19
WARNING indicates a hazardous
situation which, if not avoided, could
NOTICE is used to address
practices not related to
physical injury.
EPA Registered
#084221-AZ-001
Advertisement
Related Manuals for Paramount Fitness Ultra UV2
Summary of Contents for Paramount Fitness Ultra UV2
- Page 1 Ballast Replacement Instructions Signal Words and Symbols Used In This Manual This installation guide contains specific precautions and symbols to identify safety-related information. You will find DANGER, CAUTION, WARNING and NOTICE symbols which require special attention. Please read them carefully and follow these precautions as indicated! They will explain how to avoid hazards that may endanger you or persons using or maintaining your pool or spa.
-
Page 2: Important Notes
Turn off the power supply to the Ultra UV2 unit. Turn off power to the pool pump. DANGER Disconnect the input power to the installed Ultra UV2: • For 120v units unplug the supply cord from the GFCI. • For 230v units disconnect the incoming power by switching the circuit breaker off. - Page 3 CONFIGURATION 1 BALLAST REPLACEMENT NOTE: IF REPLACING 2 BALLASTS REPEAT STEPS 1-7 FOR SECOND BALLAST 1. Disconnect all lamps by pressing the 2. Disconnect the bulkhead connector(s). release tabs on connectors and gently pulling apart. 3. Remove the 2 mounting screws and lift 4.
- Page 4 CONFIGURATION 2: SINGLE BALLAST REMOVAL NOTE: IF REMOVING 2 BALLASTS REPEAT STEPS 1-6 FOR SECOND BALLAST (PAGE 6) 1. Disconnect all lamps by pressing the 2. Remove the nut(s) from the grounding release tab(s) on connector(s) and post(s). Remove the ballast ground wire(s) gently pulling apart.
- Page 5 CONFIGURATION 2: SINGLE BALLAST INSTALL Populate the output side of the new ballast with the correct lamp connector harness wires: Connect all the color wires to the corresponding color inputs in the ballasts. Please note that the side terminal, not back side terminal, should be used. 2 Lamp unit 1 Lamp unit SINGLE BALLAST WIRING...
- Page 6 CONFIGURATION 2: 2 BALLASTS INSTALL Populate the output side of the new ballast with the correct lamp connector harness wires: Connect all the color wires to the corresponding color inputs in the ballasts. Please note that the side terminal, not back side terminal, should be used. 2 Lamp unit 1 Lamp unit You will need to use some of the additional...