Interrupt triggered by an smu alarm, aurix tc2xx microcontroller training (10 pages)
Summary of Contents for Infineon PBA 313 07
Page 1
P r e l i m i n a r y P r o d u c t O v e r v i e w T3130-7V10PO1-7600 A p r - 2 0 0 4 PBA 313 07 Singlestone Secure Mobile Solutions...
Page 2
Exclusion of Warranty and Liability The Software is provided "as is" and Infineon gives no warranty - expressly or implied - of any kind, including, but not limited to, warranties of merchantability or fitness for a particular purpose, nor does Infineon assume any liability whatsoever as to the performance of the Software.
The module is built around the BlueMoon Single Cellular chip (PMB 8761) which contains the radio, baseband, link manager and HCI functionality. For additional information regarding the PMB8761 such as firmware features, complete description of Infineon specific HCI commands and events, please refer to the latest version of the Data sheet for PMB8761, T8761-XV01Dx-7600.
PBA 313 07 2 General Device Overview Infineon’s Singlestone - PBA 313 07 is a ready-to-use Class2 Bluetooth module solution targeted for data and audio applications in the 10 meters personal area range. BLUETOOTH wireless technology is an open industry standard for short range wireless communication with both data and voice transmission capability (up to 723 kbit/s data asymmetrically or up to 3 voice channels simultaneously).
• Baseband, Link Manager and HCI functionality is incorporated by ProBlue Firmware in chip- integrated ROM. • Infineon specific HCI+ commands to support enhanced features • Configuration data (e.g. Bluetooth device address) are loaded from internal E PROM after reset.
Singlestone PBA 313 07 2.4 Mechanical dimension and pad arrangement Below shows the module’s pad layout. All dimensions are in mm. Figure 2-3 Mechanical dimensions, pad arrangement. Dimension min. typ. max. Unit Length 11.65 11.85 12.05 Width 10.40 10.6 10.80...
Singlestone PBA 313 07 2.5 Module pin-out Table 2-2 represents the functional description of Singlestone’s connecting pads. Functionally non- used pads (NC) are used as sacrifice pads or test pads, and must not be connected in an application. Pin Location...
Power management unit UART Digital Link Control Section Analog RF-Section Analog Baseband Section Interface E 2 PROM 26 MHz XO UART GPIO JTAG WAKEUP 32.768 kHz VSUPPLY (3.0V – 4.75V) Figure 2-4: Singlestone PBA 313 07 Block diagram Preliminary Product Overview 4/2004...
Singlestone PBA 313 07 2.7 System Integration and Applications 2.7.1 General description On the RF-side, Singlestone provides a 50 Ohm single-ended input/output to be directly connected to an external antenna. The design of the antenna is open to a broad spectrum (e.g. PCB antenna, ceramic antenna, external antenna) and can be optimized to the target application requirements.
Singlestone PBA 313 07 3 Electrical Specifications 3.1 Absolute Maximum Ratings The maximum ratings may not be exceeded under any circumstances, not even momentarily and individually, as permanent damage to the module will result. Parameter Limit values Unit min. max.
Singlestone PBA 313 07 3.5 Capacitance T = 25°C Symbol Parameter Limit Values min. max. Unit input capacitance COUT output capacitance Table 3-3: Capacitance 3.6 Current consumption Regulator input voltage: V = 3.0..4.75V SUPPLY Bluetooth mode Average Consumption Unit Test Conditions min.
Singlestone PBA 313 07 3.7 DC Characteristics of Digital Part VSUPPLY = 3.0V..4.75V. Maximum allowed input levels are from -0.3V to 3.0V. Higher voltages up to 3.6V can be applied at UARTIN, UARTCTS, PCMIN, PCMFR, PCMCLK, TRST, TCK, TMS, TDI, RESETQ, CLK32, WAKEUP_BT.
Singlestone PBA 313 07 Pull-Up and Pull-Down Values Symbol Pull-Up Pull-Down Unit Test Condition UARTRTS µA UARTOUT µA WAKEUP_HOST µA PCMOUT µA PCMFR µA PCMCLK µA GPIO0 µA Table 3-8: Pull-Up / Pull-Down characteristics 3.7.1 Pull Up characteristics on ResetQ The ResetQ signal is pulled up to Vdd.
Singlestone PBA 313 07 3.9.1 Transmitter Characteristics Parameter Symbol Limit values Unit Test Conditions min. typ. max. Output power -3.0 Output power -1.0 T=25°C Frequency deviation (00001111 sequence) Frequency deviation (0101 sequence) Relative frequency 0.95 dev,0101 dev,00001111 deviation (0101 sequence)
Singlestone PBA 313 07 3.9.3 Receiver Characteristics Parameter Range/Location Limit values Unit Test Conditions min. typ. max. Sensitivity (BER=10 According to Bluetooth spec. Sensitivity (BER=10 T=25°C, nominal transmitter Interference frequency deviation performance Y=M±1 160kHz for wanted (BER=10 Y=M-2 (M) and interferer (Y),...
Singlestone PBA 313 07 Assembly and design guidelines 4.1 General description of the module Singlestone is a Land Grid Array (LGA 8x9) module made for surface mounting. The pad diameter is 0.8 mm and the pitch 1.27 mm. All solder joints on the module will reflow during soldering on the mother board. All components and shield will stay in place due to wetting force.
Singlestone PBA 313 07 4.4 Assembly 4.4.1 Component placement In order to assure a high yield soldering process good placement on the PCB is necessary. As a rule of thumb the tolerable misplacement is 150 µm. This means that the Singlestone module can be assembled with a variety of placement systems.
Singlestone PBA 313 07 4.5 Soldering profile Generally all standard reflow soldering processes (vapour phase, convection, infra red) and typical temperature profiles used for surface mount devices are suitable for the Singlestone module. Wave soldering is not possible. Figure 4-3 shows an example of a suitable solder reflow profile.
Singlestone PBA 313 07 5 Type approvals and Qualification 5.1 Bluetooth Qualification The PBA 31307 is Bluetooth Qualified according to specification v1.1 with the ID: PBA31307. The covered functionality of this listing covers RF, Baseband and Link Manager. Since the PBA 31307 constitute a complete Bluetooth system, the pre-testing, listings and qualifications can be reused by reference by the end-customer.
Singlestone PBA 313 07 6 Module marking Marking Description Infineon logotype 2. <PBA 313 07 Product number with suffix and revision state according to R1A> purchase order. 3. <bbbbbb> Batch number 4. <XX> Type of module: Engineering Samples, XX=ES 5. <yyww2>...
Singlestone PBA 313 07 7 Package Singlestone is packed in tape on reel according to Figure 7-1. The tape is also the module dry pack as referred to in chapter 4.5. Figure 7-1 Tape on reel for Singlestone Preliminary Product Overview...