Related Manuals for Life Fitness CLUB SERIES BACK EXTENSION
Summary of Contents for Life Fitness CLUB SERIES BACK EXTENSION
- Page 1 CLUB SERIES BACK EXTENSION ASSEMBLY INSTRUCTIONS Part # 7137301 Revision:7/16/01 Rev A.
-
Page 2: Table Of Contents
PARTS LIST PART # DESCRIPTION PART # DESCRIPTION 70087xx TOWER 6923602 HEAD PLATE 7015201 CABLE 3102901 3/8 X 1-1/4” BOLT 6925801 KEEP CLEAR LABEL 3102903 3/8 X 2-1/2” BOLT 6714901 GUIDE ROB BUSHING 3102922 3/8 X 2-3/4” BOLT 3102514 3/8 FLAT WASHER 3102942 3/8 X 3-1/2”... - Page 3 2"...
- Page 4 10 3/8 X 2-3/4” 12 3/8 X 3-3/4” FIGURE 1 STEP 1: • LOOSELY assemble the CROSS SUPPORT (3) to the lower tube on the TOWER (1) using four RH CAPS (33), two 3/8 X 3-3/ 4” BOLTS (12), four 3/8” SAE WASHERS (15), four 3/8” RH WASHERS (16) and two 3/8” LOW HEIGHT LOCK NUTS (14) as shown in FIGURE 1.
- Page 5 12 3/8 X 3-3/4” FIGURE 2 STEP 2: • LOOSELY assemble the FOOT SUPPPORT (2) to the CROSS SUPPORT (3) using four RH CAPS (33), two 3/8 X 3-3/4” BOLTS (12), four 3/8” SAE WASHERS (15), four 3/8” RH WASHERS (16), and two 3/8” LOW HEIGHT LOCK NUTS (14) as shown in FIGURE 2.
-
Page 6: X 3-1/2" Bolt
11 3/8 X 3-1/2” FIGURE 3 STEP 3 • SECURELY assemble the CAM SHROUD (6) to the CROSS SUPPORT (3) using two BLACK RH CAPS (20 ), two RH CAPS (33), two 3/8 X 3-1/2” BOLTS (11), four 3/8” SAE WASHERS (15), four 3/8” RH WASHERS (16) and two 3/8” LOW HEIGHT LOCK NUTS (14) as shown in FIGURE 3. -
Page 7: Low Height Lock Nut
13 3/8 X 3” BUTTON HEAD FIGURE 4 STEP 4 • Slide one ACCORDION SLEEVE (24) and two PILLOW BLOCKS (17) over the PIVOT ARM (4) as shown in FIGURE 4 • Assemble four 3/8 X 3” BUTTON HEAD CAP SCREWS (13) and four STARLOCK WASHERS (32) to the the PILLOW BLOCKS (17) as shown in FIGURE 4 13 3/8 X 3”... - Page 8 FIGURE 6 STEP 6: • Assemble one RUBBER BUMPER (22) to the PIVOT ARM (4) where the PIVOT ARM (4) contacts the shaft on the CROSS SUPPORT (3). FIGURE 7 CABLE STEP 7: • Slide the end of the CABLE into the bushing on the PIVOT ARM (4) as shown in FIGURE 7.
-
Page 9: Rh Washer
8 3/8 X 1-1/4” FIGURE 8 STEP 8: • SECURELY assemble two SEAT PADS (30) to the seat plates on the CROSS SUPPORT (3) using four RH CAPS (33), four 3/8 X 1-1/4” BOLTS (8) and four 3/8” RH WASHERS (16) as shown in FIGURE 8. -
Page 10: Weight Stack Selector Pin
HEAVY WEIGHT OPTION FIGURE 9 STEP 9: • Insert the two GUIDE RODS (27) (found in SHROUD KIT) into the base of the TOWER (1) as shown in FIGURE 9. Lubricate the GUIDE RODS (27) with a silicon or teflon spray that is available at most hardware stores. •... -
Page 11: Shaft Collar
FIGURE 10 9 3/8 X 2-1/2” TIGHTEN! STEP 10: • SECURELY assemble the GUIDE ROD SUPPORT (5) to the TOWER (1) using four RH CAPS (33), two 3/8 X 2-1/2” BOLTS (9), four 3/8” RH WASHERS (16) and two 3/8” LOW HEIGHT LOCK NUTS (14) as shown in FIGURE 10. •... - Page 12 FIGURE 11 STEP 11: • The WEIGHT STACK LABEL sheet (31) includes labels for both lbs. and kgs. for both the standard and optional weight stacks. • Peel the backing off the WEIGHT STACK LABELS (31), line up sheet to the right of the selector opening and apply labels to the WEIGHT PLATES (28 or 29), starting with the HEAD PLATE (7) as shown in FIGURE 11.
-
Page 13: Language Placard Label
FRONT SHROUD FIGURE 12 STEP 12: • Assemble the PLACARD LABEL (25) or the FOREIGN LANGUAGE PLACARD LABEL (26) to the FRONT SHROUD as shown in FIGURE 12. -
Page 14: Guide Rod
• Lube the Guide Rods. Apply the lubricant to a cotton cloth, then run the cotton cloth up and down the guide rods as needed. Do not spray lubricant directly on the Guide Rods. Thank you for purchasing the LifeFitness CLUB SERIES BACK EXTENSION. If unsure of proper use of equipment, call your local LifeFitness distributor or call the LifeFitness customer service department at...