YASKAWA CIMR-VC series Quick Start Manual page 30

6 Parameter Table
Par. Name
Digital Input Settings
H1-01 DI S1 to S6
Selects the function of terminals S1
to Function
to S6.
H1-06 Selection
Major functions are listed at the end of the table.
Digital Output Settings
DO MA/MB Set the function for the relay output
H2-01
Function MA-MB-MC.
DO P1 Sets the function for the photocou-
H2-02
Function pler output P1.
DO P2 Sets the function for the photocou-
H2-03
Function pler output P2.
Major functions are listed at the end of the table.
Analog Input Setting
A1 Signal 0:0 to +10 V (neg. input is zeroed)
H3-01
Level Sel. 1:0 to +10 V (bipolar input)
A1
H3-02 Assign a function to terminal A1.
Function Sel.
Sets the input value in % at 10 V
H3-03 A1 Gain
analog input.
Sets the input value in % at 0 V
H3-04 A1 Bias
analog input.
0:0 to +10 V (neg. input is zeroed)
A2 Signal
1:0 to +10 V (bipolar input)
H3-09 Level Selec-
2:4 to 20 mA (9 bit input)
tion
3:0 to 20 mA
A2
H3-10 Assign a function to terminal A2.
Function Sel.
Sets the input value in % at
H3-11 A2 Gain
10 V/20 mA analog input.
Sets the input value in % at
H3-12 A2 Bias
0 V/0 mA/4 mA analog input.
Analog Input Setting
AM Enter value equal to U1-
H4-01 Monitor monitor values. Example: Enter
Selection "103" for U1-03.
Sets terminal AM output voltage
H4-02 AM Gain
equal to 100% monitor value.
Sets terminal AM output voltage
H4-02 AM Bias
equal to 0% monitor value.
EN 28
Description
YASKAWA Europe TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide
Par. Name
Pulse Input Setting (Free. ref. input)
RP Input Sets the number of pulses (in Hz)
H6-02
Scaling that is equal to 100% input value.
Pulse Train Sets the input value in % at pulse
H6-03
Input Gain input with H6-02 frequency.
Pulse Train Sets the input value in % at 0 Hz
H6-04
Input Bias pulse input frequency.
Pulse Output Setting
Enter value equal to U -
MP Monitor
H6-06 monitor values. Example: Enter
Sel.
"102" for U1-02.
MP Monitor Sets the number of output pulses
H6-07
Scaling when the monitor is 100% (in Hz).
Motor Overheat Protection
Sets the motor overload protection.
Motor Over- 0:Disabled
L1-01 load Prot. 1:Standard fan cooled motor
Sel. 2:Standard blower cooled motor
3:Vector motor
Motor Over- Sets the motor overload protection
L1-02 load Prot. time in min. Normally no change is
Time necessary.
Stall Prevention
0:Disabled - Motor accelerates at
active acceleration rate and may
Stall stall with too heavy load or too
Prevention short accel time.
L3-01 Selection 1:General Purpose - Hold
during acceleration when current is
Acceleration above L3-02.
2:Intelligent - Acceleration in the
shortest possible time.
Stall Prev.
Sets the current level for stall pre-
L3-02 Level dur-
vention during acceleration.
ing Accel.
0:Disabled - Deceleration as set.
Stall Prev.
OV might occur.
Selection
L3-04 1:General Purpose - Deceleration
during
is hold if DC bus voltage rises
Decel.
high.
0:Disabled - Motor stall or
Stall Prev.
overload might occur.
L3-05 Selection
1:Decel Time 1 - Reduce speed
during Run
using C1-02.
Description