Related Manuals for 3xLogic VISIX VX-FR-01
Summary of Contents for 3xLogic VISIX VX-FR-01
- Page 1 VISIX VX-FR-01 Facial Recognition Camera Hardware Installation Manual 2018-1 12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC...
- Page 2 VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual This manual applies to the following camera models: Camera Type Model VISIX Facial Recognition Camera VX-FR-01 Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer.
- Page 3 VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
- Page 4 VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. The precaution measure is divided into ‘Warnings’ and ‘Cautions’: Warnings: Serious injury or death may be caused if any of these warnings are neglected.
- Page 5 VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual Caution: Make sure the power supply voltage is correct before using the camera. Do not drop the camera or subject it to physical shock. Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a bit of ethanol ...
-
Page 6: Table Of Contents
VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual Table of Contents 1 CAMERA OVERVIEW ............................. 7 ............................8 AMERA ESCRIPTION 2 INSTALLATION ............................... 9 ........................... 9 NSTALLATION UIDELINES ............................. 10 AMERA NSTALLATION 2.2.1 Installation – Routing Cabling through Bottom ................. 10 2.2.2 Installation –... -
Page 7: Camera Overview
VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual 1 Camera Overview The 3xLOGIC VISIX Facial Recognition VX-FR-01 is a special purpose, low cost dual lens 2MP camera for instant face detection, identification, and notification of persons of interest (POI). Using camera based analytics and 3xLOGIC’s exclusive Facial Recognition application and mobile app, users can review captured facial images... -
Page 8: Camera Description
VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual Camera Description See below for descriptions of the different camera components. Camera Overview Figure 1-2 Number Description Camera Base Cover / Mounting Plate Camera Base Safety Wire Ethernet (RJ-45) -
Page 9: Installation
VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual 2 Installation Installation Guidelines When installing the VX-FR-01, the following guidelines should be followed to insure highest facial recognition accuracy. The camera must be installed facing the people entering the area to be surveilled. -
Page 10: Camera Installation
VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual Camera Installation The VX-FR-01 can be installed on a ceiling or wall with cabling routed through the bottom of the mounting base (A) or through the side of the mounting base (B). - Page 11 VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual 2. After you finish marking the installation surface with the pencil, use a drill with a 5.5mm bit to drill the holes for the fastening screws. Insert the supplied anchors into the holes. Use a 40mm hole cutting bit to cut-out the cable routing hole.
-
Page 12: Installation - Routing Cable Through Side
VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual 4. Fasten the camera base cover to the wall with the supplied screws. Fastening the Base Cover to the Installation Surface Figure 2-6 Please continue to Section 2.2.3 for instructions on finalizing installation. - Page 13 VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual 2. After you finish marking the installation surface with the pencil, use a drill with a 5.5mm bit to drill the holes for the fastening screws. Insert the supplied anchors into the holes.
-
Page 14: Installation - Finalizing Camera Installation
VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual 2.2.3 INSTALLATION – FINALIZING CAMERA INSTALLATION 1. After routing the cabling using your preferred method, attach the safety wire located in the base of your camera to the camera base cover. This will ensure the camera base stays attached to the fixed base cover during maintenance or adjustments. - Page 15 VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual 2. Attach the GND wire from your cabling harness to the grounding point located in the camera mount base. Attaching GND Wiring Figure 2-11 12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC...
- Page 16 VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual 3. Splice the alarm relay / audio /accessory interface wiring together. Splicing Relay / Audio / Accessory Interface Figure 2-12 12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC...
- Page 17 VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual 4. Attach the 36VDC power supply and RJ-45 Ethernet cables. Attaching Ethernet and Power Supply Figure 2-13 5. Prepare the camera for fastening to the base cover For installations where cabling is routed through the bottom, be sure the cabling is situated within camera base in such a manner that the camera can be attached flush to the base cover.
- Page 18 VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual A) Routing Cable Through Bottom Figure 2-14 Remove and discard the cover for the side cable routing hole. Route the cabling through the hole. Be sure the cabling is situated so the camera base can be attached flush to the base cover.
- Page 19 VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual 6. Attach the camera to the mounted base cover by joining the camera base and cover and sliding the camera into place. Attaching Camera Base to Mounted Base Cover Figure 2-16 12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC...
-
Page 20: Installation - Adjusting Viewing Angle
VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual 2.2.4 INSTALLATION – ADJUSTING VIEWING ANGLE 1. Adjust the head of the camera to achieve the desired tilt angle. Adjust Tilt Angle Figure 2-17 2. Pan the camera around to achieve the desired field-of-vision. - Page 21 VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual 3. Discard the protective film from the camera lens face. Discarding Protective Film Figure 2-19 12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC...
-
Page 22: Installation - Micro Sd Card
VISIX SOLUTIONS | VISIX VX-FR-01 Facial Recognition Camera – Hardware Installation Manual 2.2.5 INSTALLATION — MICRO SD CARD Steps: 1. Open the Micro SD reader dust cover Installing MicroSD Card – Opening Dust Cover Figure 2-20 2. Insert the Micro SD Card into the slot Installing MicroSD Card –... - Page 23 © 2018 3xLOGIC Inc. All rights reserved. Information in this document is subject to change without notice. 3xLOGIC and the 3xLOGIC logo are trademarks of 3xLOGIC, Inc. all other trademarks are property of their respective owners. Revised: August 14, 2018...