SEW-Eurodrive Movidrive MDX61B Operating Instructions Manual
  1. Manuals
  2. Brands
  3. SEW-Eurodrive Manuals
  4. DC Drives
  5. Movidrive MDX61B
  6. Operating instructions manual

SEW-Eurodrive Movidrive MDX61B Operating Instructions Manual

Hide thumbs Also See for Movidrive MDX61B:
Table of Contents

Advertisement

Quick Links

See also: System Manual , Manual
*23534850_1117*
Drive Technology \ Drive Automation \ System Integration \ Services
Operating Instructions
®
MOVIDRIVE
MDX60B/61B
Edition 11/2017
23534850/EN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Movidrive MDX61B and is the answer not in the manual?

Questions and answers

Related Manuals for SEW-Eurodrive Movidrive MDX61B

Summary of Contents for SEW-Eurodrive Movidrive MDX61B

  • Page 1 *23534850_1117* Drive Technology \ Drive Automation \ System Integration \ Services Operating Instructions ® MOVIDRIVE MDX60B/61B Edition 11/2017 23534850/EN...
  • Page 2 SEW-EURODRIVE—Driving the world...

  • Page 3: Table Of Contents

    Table of contents Table of contents General information........................  7 About this documentation .................... 7 Structure of the safety notes ................... 7 Rights to claim under limited warranty ................ 8 Exclusion of liability...................... 8 Other applicable documentation .................. 8 Product names and trademarks.................. 9 Copyright notice ...................... 9 Safety notes ..........................
  • Page 4 Table of contents 4.13 Connecting the USB11A interface adapter .............. 113 4.14 Option combinations for MDX61B................ 115 4.15 Installing and removing option cards ................ 118 4.16 Connecting encoders and resolvers ................ 120 ® 4.17 Connection and terminal description of the DEH11B option (HIPERFACE )  .. 122 4.18 Connection and terminal description of the DEH21B option........ 124 4.19...
  • Page 5 Table of contents Technical data of regenerative power supply unit ............  263 ® MOVIDRIVE MDR60A/61B regenerative power supply unit  ........ 263 Technical data of options ....................  278 ® 10.1 HIPERFACE encoder card DEH11B ................ 278 10.2 Resolver card DER11B.................... 279 10.3 DEU21B multi-encoder card .................. 280 10.4 DEH21B/DIP11B absolute encoder card .............. 281 10.5...
  • Page 6 Table of contents 12.2 ND.. line chokes...................... 349 12.3 NF...-... line filters...................... 351 12.4 HD... output chokes .................... 355 12.5 HF... output filter ...................... 358 Declarations of conformity ....................  362 ® 13.1 MOVIDRIVE   ...................... 362 ® 13.2 MOVIDRIVE with DFS11B/DFS21B ................. 363 ® 13.3 MOVIDRIVE with DCS2.B/DCS3.B ................ 364 Address list ...........................

  • Page 7: General Information

    General information About this documentation General information About this documentation The current version of the documentation is the original. This documentation is an integral part of the product. The documentation is written for all employees who assemble, install, start up, and service this product. Make sure this documentation is accessible and legible.

  • Page 8: Rights To Claim Under Limited Warranty

    General information Rights to claim under limited warranty Hazard symbol Meaning Warning of dangerous electrical voltage Warning of hot surfaces Warning of risk of crushing Warning of suspended load Warning of automatic restart 1.2.3 Structure of embedded safety notes Embedded safety notes are directly integrated into the instructions just before the de- scription of the dangerous action.

  • Page 9: Product Names And Trademarks

    General information Product names and trademarks Product names and trademarks The brands and product names in this documentation are trademarks or registered trademarks of their respective titleholders. Copyright notice © 2017 SEW‑EURODRIVE. All rights reserved. Unauthorized reproduction, modifica- tion, distribution or any other use of the whole or any part of this documentation is strictly prohibited.

  • Page 10: Safety Notes

    Safety notes General Safety notes The following basic safety notes must be read carefully to prevent injury to persons and damage to property. The operator must ensure that the basic safety notes are read and adhered to. Make sure that persons responsible for the plant and its opera- tion, as well as persons who work independently on the device, have read through the operating instructions carefully and understood them.

  • Page 11: Designated Use

    Safety notes Designated use Designated use Drive inverters are components intended for installation in electrical systems or ma- chines. In case of installation in machines, startup of the inverters (meaning the start of desig- nated use) is prohibited until it is determined that the machine meets the requirements stipulated in the Machinery Directive 2006/42/EC;...

  • Page 12: Electrical Connection

    Safety notes Electrical connection Electrical connection Observe the applicable national accident prevention guidelines when working on live inverters (e.g. BGV A3). Electrical installation must be carried out in compliance with pertinent regulations (e.g. cable cross sections, fusing, protective conductor connection). For any additional in- formation, refer to the applicable documentation.
  • Page 13 Safety notes Operation WARNING Electric shock due to charged capacitors. Dangerous voltage levels may still be present inside the device and at the terminals up to 10 minutes after disconnection from the power supply. Severe or fatal injuries. • Wait for 10 minutes after the frequency inverter has been separated from the voltage supply.

  • Page 14: Device Structure

    Device structure Type designation, nameplates and scope of delivery Device structure Type designation, nameplates and scope of delivery 3.1.1 Type designation ® The following diagram shows the type designation of the MOVIDRIVE MDX60/61B inverter: MDX60 B 0011 - 5 A 3 - 4 00 Design 00 = Standard 0T = Application...
  • Page 15 Device structure Type designation, nameplates and scope of delivery 3.1.4 System nameplate for sizes 1 – 7 The system nameplate is attached to MDX61B.. as follows: • On the side of the device in size 1 – 6 • On the upper front cover of size 7 18014400309212299 3.1.5 Power section nameplate for sizes 1 – 7...

  • Page 16: Scope Of Delivery

    Device structure Scope of Delivery 3.1.6 Control unit nameplate for sizes 1 – 7 The control unit nameplate is attached to the front of MDX61B.. size 1 – 7. 9007201054503051 3.1.7 Option card nameplate 9007201054506123 Scope of Delivery 3.2.1 Sizes 0 – 7 • Connector housing for signal terminals (X10 – X17), connected. •...
  • Page 17 Device structure Scope of Delivery 3.2.3 Sizes 1 – 7 • 1 set of shield clamps for signal cable, not installed. The set of shield clamps com- prises: – 1 shield clamp for signal cable (1 contact clip) – 2 contact clips –...

  • Page 18: Size 0

    Device structure Size 0 Size 0 MDX60/61B-5A3 (AC 400/500 V devices): 0005/0008/0011/0014 [15] [14] [13] [12] [11] [10] [16] [17] [18] [20] [19] 2205806347 *View of the bottom of the device [1] Power shield clamp for supply system connection and DC link connection [2] X4: Connection for DC link coupling -U and PE connection, separable [3] X1: Power supply connection L1, L2, L3 and PE connection, separable...

  • Page 19: Size 1

    Device structure Size 1 Size 1 MDX61B-5A3 (AC 400/500 V devices): 0015/0022/0030/0040 MDX61B-2A3 (AC 230 V devices): 0015/0022/0037 [19] [18] [17] [16] [15] [14] [13] [12] [11] [10] 2205808267 [1] X1: Power supply connection 1/L1, 2/L2, 3/L3, separable [2] X4: Connection for DC link coupling -U , separable [3] Fieldbus slot [4] Expansion slot...
  • Page 20 Device structure Size 1 [15] Grounding screw M4 × 14 [16] DIP switches S11 – S14 [17] XT: Slot for DBG60B keypad or USB11A/UWS21B serial interface [18] 7-segment display [19] Memory card ® Operating Instructions – MOVIDRIVE MDX60B/61B...

  • Page 21: Size 2S

    Device structure Size 2S Size 2S MDX61B-5A3 (AC 400/500 V devices): 0055/0075 [19] [18] [17] [16] [15] [14] [13] [12] [11] [10] 2205796747 [1] X1: Line connection 1/L1, 2/L2, 3/L3 [2] X4: Connection for DC link coupling –U and PE connection [3] Memory card [4] Fieldbus slot [5] Expansion slot...
  • Page 22 Device structure Size 2S [16] Grounding screw M4 × 14 [17] DIP switches S11 – S14 [18] XT: Slot for DBG60B keypad or USB11A/UWS21B serial interface [19] 7-segment display ® Operating Instructions – MOVIDRIVE MDX60B/61B...

  • Page 23: Size 2

    Device structure Size 2 Size 2 MDX61B-5A3 (AC 400/500 V devices): 0110 MDX61B-2A3 (AC 230 V devices): 0055/0075 [19] [18] [17] [16] [15] [14] [13] [12] [11] [10] 2205794827 [1] X1: Line connection 1/L1, 2/L2, 3/L3 [2] X4: Connection for DC link coupling –U and PE connection [3] Fieldbus slot [4] Expansion slot...
  • Page 24 Device structure Size 2 [12] X13: Signal terminal strip terminal strip for digital inputs and RS485 interface [13] X11: Signal terminal strip for setpoint input AI1 and 10 V reference voltage [14] X12: Signal terminal strip system bus (SBus) [15] Grounding screw M4 × 14 [16] DIP switches S11 – S14 [17] XT: Slot for DBG60B keypad or USB/11AUWS21B serial interface [18] 7-segment display...

  • Page 25: Size 3

    Device structure Size 3 Size 3 Size 3 is available in 2 hardware designs that can be distinguished using the name- plate. MDX61B-503 (AC 400/500 V devices): 0150/0220/0300 MDX61B-203 (AC 230 V devices): 0110/0150 The version before the redesign does not have entries in the status fields 2 and 5 of the nameplate.
  • Page 26 Device structure Size 3 [5] Expansion slot [6] Encoder slot [7] X3: Braking resistor connection 8/+R, 9/–R [8] X2: Motor connection 4/U, 5/V, 6/W [9] Shield clamp for signal cables and PE connection [10] X17: Signal terminal block for safety contacts of drive safety function STO [11] X10: Signal terminal strip for digital outputs and TF/TH input [12] X16: Signal terminal strip digital inputs and outputs [13] X13: Signal terminal strip terminal strip for digital inputs and RS485 interface...
  • Page 27 Device structure Size 3 [20] [19] [18] [17] [16] [15] [14] [13] [12] [11] [10] 19300062475 [1] PE connection [2] X1: Line connection 1/L1, 2/L2, 3/L3 [3] X4: Connection for DC link coupling -U [4] Fieldbus slot [5] Expansion slot [6] Encoder slot [7] X3: Braking resistor connection 8/+R, 9/–R [8] X2: Motor connection 4/U, 5/V, 6/W...
  • Page 28 Device structure Size 3 [20] Memory card ® Operating Instructions – MOVIDRIVE MDX60B/61B...

  • Page 29: Size 5

    Device structure Size 4 Size 4 MDX61B-503 (AC 400/500 V devices): 0370/0450 MDX61B-203 (AC 230 V devices): 0220/0300 [21] [20] [19] [18] [17] [16] [15] [14] [13] [12] [11] [10] 2205800587 [1] PE connection [2] X1: Line connection 1/L1, 2/L2, 3/L3 [3] X4: Connection for DC link coupling –U and PE connection [4] Fieldbus slot...
  • Page 30 Device structure Size 4 [16] X12: Signal terminal strip system bus (SBus) [17] Grounding screw M4 × 14 [18] DIP switches S11 – S14 [19] XT: Slot for DBG60B keypad or USB11A/UWS21B serial interface [20] 7-segment display [21] Memory card ® Operating Instructions – MOVIDRIVE MDX60B/61B...

  • Page 31: Size 6

    Device structure Size 5 Size 5 MDX61B-503 (AC 400/500 V devices): 0550/0750 [21] [20] [19] [18] [17] [16] [15] [14] [13] [12] [11] [10] 2205802507 [1] PE connection [2] X1: Line connection 1/L1, 2/L2, 3/L3 [3] X4: Connection for DC link coupling –U and PE connection [4] Fieldbus slot [5] Expansion slot...
  • Page 32 Device structure Size 5 [14] X13: Signal terminal strip terminal strip for digital inputs and RS485 interface [15] X11: Signal terminal strip for setpoint input AI1 and 10 V reference voltage [16] X12: Signal terminal strip system bus (SBus) [17] Grounding screw M4 × 14 [18] DIP switches S11 – S14 [19] XT: Slot for DBG60B keypad or USB11A/UWS21B serial interface [20] 7-segment display...

  • Page 33: Size 7

    Device structure Size 6 3.10 Size 6 MDX61B-503 (AC 400/500 V devices): 0900/1100/1320 [20] [19] [18] [17] [16] [15] [14] [13] [12] [11] [10] 2205804427 [1] PE connection [2] X1: Line connection 1/L1, 2/L2, 3/L3 [3] X4: Connection for DC link coupling -U [4] Fieldbus slot [5] Expansion slot [6] Encoder slot...
  • Page 34 Device structure Size 6 [17] DIP switches S11 – S14 [18] XT: Slot for DBG60B keypad or USB11A/UWS21B serial interface [19] 7-segment display [20] Memory card ® Operating Instructions – MOVIDRIVE MDX60B/61B...
  • Page 35 Device structure Size 7 3.11 Size 7 3.11.1 Control unit MDX61B-503 (AC 400/500 V devices): 1600/2000/2500 [19] [17] [16] [15] [14] [13] [12] [11] [10] 2077051275 [4] Fieldbus slot [5] Expansion slot [6] Encoder slot [7] Shield clamp for signal cables [8] X17: Signal terminal block for safety contacts of drive safety function STO [9] X10: Signal terminal strip for digital outputs and TF/TH input [10] X16: Signal terminal strip digital inputs and outputs...
  • Page 36 Device structure Size 7 3.11.2 Power section MDX61B-503 (AC 400/500 V devices): 1600/2000/2500 2077053963 [1] PE connection rail (thickness = 10 mm) [2] X1: Line connection 1/L1, 2/L2, 3/L3 [3] X3: Braking resistor connection 8/+R, 9/–R [4] X2: Motor connection 4/U, 5/V, 6/W [5] -U : Only with DC link adapter accessory ®...
  • Page 37 Device structure Size 7 3.11.3 DC power supply unit MDX61B-503 (AC 400/500 V devices): 1600/2000/2500 [2] 5x 20089692683 [1] DC power supply unit [2] Screw Connections for power supply unit (PE L1 L2 L3) • Cross section: 6 mm • Tightening torque ≤ 4 mm = 0.5 Nm •...

  • Page 38: Movidrive ® Mdx62B Motor Inverter Size 7

    Device structure MOVIDRIVE® MDX62B motor inverter size 7 MOVIDRIVE ® MDX62B motor inverter size 7 ® 3.12 MOVIDRIVE MDX62B motor inverter size 7 3.12.1 Control unit MDX62B-503 (AC 400/500 V devices): 1600 / 2000 / 2500 [19] [17] [16] [15] [14] [13] [12]...
  • Page 39 Device structure MOVIDRIVE® MDX62B motor inverter size 7 3.12.2 Power section MDX62B-503 (AC 400/500 V devices): 1600 / 2000 / 2500 3956576011 [1] PE connection rail (thickness = 10 mm) [2] X3: Braking resistor connection 8/+R, 9/–R [3] X2: Motor connection 4/U, 5/V, 6/W [4] -U : Only with DC link adapter accessory ®...
  • Page 40 Device structure MOVIDRIVE® MDX62B motor inverter size 7 3.12.3 DC power supply unit MDX62B-503 (AC 400/500 V devices): 1600 / 2000 / 2500 [2] 5x 9007201561717259 [1] DC power supply unit [2] Screw ® Operating Instructions – MOVIDRIVE MDX60B/61B...

  • Page 41: Installation

    Installation Installation instructions for the basic unit Installation ® MOVIDRIVE B application inverters are exclusively suitable for control cabinet install- ation according to the degree of protection. Installation instructions for the basic unit 4.1.1 General installation notes for size 0 – 6 The retaining screws [1] and [2] are screwed into the prepared mounting grid in the control cabinet but not tightened.
  • Page 42 Installation Installation instructions for the basic unit 4. Tighten the retaining screws [1] and [2]. Installation notes for size 7 SEW‑EURODRIVE recommends the following SEW accessories for control cabinet in- ® stallation of MOVIDRIVE size 7: • Mounting base to be installed under the basic device –...
  • Page 43 Installation Installation instructions for the basic unit 4.1.2 Tightening torques Power terminal tightening torques Only use original connection elements. Note the permitted tightening torques for ® MOVIDRIVE power terminals. Size Tightening torque 0, 1 and 2S 4 and 5 14.0 20.0 70.0 •...
  • Page 44 Installation Installation instructions for the basic unit 4.1.3 Minimum clearance and mounting position • Leave at least 100 mm clearance above and below the device for optimum cool- ing. Make sure air circulation in the clearance is not impaired by cables or other in- stallation equipment.
  • Page 45 Installation Installation instructions for the basic unit 4.1.5 Fuses and residual current devices • Install the fuses at the beginning of the supply system lead after the supply bus junction (observe the wiring diagram for basic device, power section and brake). •...
  • Page 46 Installation Installation instructions for the basic unit 4.1.7 PE connection (EN 61800-5-1) Earth-leakage currents ≥ 3.5 mA may occur during normal operation. To meet the re- quirements of EN 61800‑5‑1 observe the following: • Supply system lead < 10 mm Route a second PE conductor with the cross section of the supply system lead in parallel to the protective earth via separate terminals or use a copper pro- tective earth conductor with a cross section of 10 mm •...
  • Page 47 Installation Installation instructions for the basic unit 4.1.10 Unit output NOTICE ® MOVIDRIVE B can suffer irreparable damage if you connect capacitive loads. • Only connect ohmic/inductive loads (motors). • Never connect capacitive loads. 1804838667 4.1.11 Permitted mounting the braking resistors WARNING Non-permissible installation might lead to an accumulation of heat in the braking res- istor due to reduced convection.
  • Page 48 Installation Installation instructions for the basic unit Grid resistors You must fulfill the following requirements for mounting the grid resistors: •    Permitted: Mounting on horizontal surfaces. •   Permitted: Mounting on vertical surfaces with terminals pointing downwards when there is a perforated sheet at the top. •...
  • Page 49 Installation Installation instructions for the basic unit Wire resistors You must fulfill the following requirements for mounting the wire resistors: •    Permitted: Mounting on horizontal surfaces. •   Permitted: Mounting on vertical surfaces when there is a perfor- ated sheet at the top or connection terminals at the bottom •...
  • Page 50 Installation Installation instructions for the basic unit WARNING The surfaces of the braking resistors get very hot when the braking resistors are loaded with P Risk of burns and fire. • Choose a suitable installation location. Braking resistors are usually mounted on top of the control cabinet.
  • Page 51 Installation Installation instructions for the basic unit 1804841739 Correct shield connection using metal clamp (shield clamp) or cable gland • You can also use earthed sheet-metal ducts or metal pipes to shield the cables. Route the power and signal cables separately. •...
  • Page 52 Installation Installation instructions for the basic unit NF.. line filter • The NF.. line filter option can be used to maintain the class C1 limit for ® MOVIDRIVE MDX60B/61B in size 0 – 5. ® • Do not switch between the line filter and MOVIDRIVE MDX60B/61B.
  • Page 53 Installation Installation instructions for the basic unit HD... output choke • Install the output choke close to the inverter but outside the minimum clearance for cooling. • For HD001  –  HD003: Route all three phases (U, V, W) of the motor cable [1] through the output choke.
  • Page 54 Installation Installation instructions for the basic unit 4.1.16 Installation notes for size 6 ® MOVIDRIVE devices in size 6 (0900  –  1320) have one fixed lifting eye [1]. Use a crane and the lifting eye [1] to install the device. WARNING Suspended load.
  • Page 55 Installation Installation instructions for the basic unit WARNING Suspended load. Danger of fatal injury if the load falls. • Do not stand under the suspended load. • Secure the danger zone. • Always use all 4 lifting eyes. • Align the lifting eyes with the direction of tension >...
  • Page 56 Installation Installation instructions for the basic unit 4.1.18 Optional scope of delivery for size 7 DLS11B mounting base The mounting base DLS11B with mounting material [9] (part no.: 18226027) is used ® ® to install MOVIDRIVE B, size 7 on the floor of the control cabinet. MOVIDRIVE size 7 must be screwed onto the mounting base immediately after installation (see fol- ®...
  • Page 57 Installation Installation instructions for the basic unit • Place the lock washer [5] and the washer [6] onto the socket head screw [4] M8×30. • Insert the preassembled socket head screw through the mounting hole. • Screw the M8 nut [8] onto the socket head screw. Tightening torque 20 Nm. Apply thread locking compound.
  • Page 58 Installation Installation instructions for the basic unit DLH11B wall bracket ® The wall bracket DLH11B [13] (part no: 18226108) is used to attach MOVIDRIVE ® size 7 to the wall (see following figure). Do not take MOVIDRIVE B size 7 into opera- tion until the installation of the device is complete.
  • Page 59 Installation Installation instructions for the basic unit The installation material for wall mounting is not included in the delivery of SEW-EURODRIVE. ® Proceed as follows to fasten the wall bracket [13] to MOVIDRIVE B size 7: 1. Loosen (not unscrew!) the 4 retaining screws of the front cover [1] until you can lift it off.
  • Page 60 Installation Installation instructions for the basic unit Dimension drawing for DLH11B wall bracket 320 (12.6) 14 (0.55) 320 (12.6) 640 (25.2) 700 (47.56) 9007201676959499 ® Operating Instructions – MOVIDRIVE MDX60B/61B...
  • Page 61 Installation Installation instructions for the basic unit DLK11B air duct An optional DLK11B air duct (part no.: 18226035) is available to dissipate heat of ® MOVIDRIVE B size 7. Install the air duct in such a way that it points vertically up- wards (see figure below).
  • Page 62 Installation Installation instructions for the basic unit 2Q DLZ12B DC link adapter The DC link adapter 2Q DLZ12B (part no.: 18227295) can be used to provide a DC link connection at the bottom of the device: [2] 4x 9007201531077515 1. Loosen the 4 screws of both the upper and lower cover and remove them. 2.
  • Page 63 Installation Installation instructions for the basic unit 9. Position the 4 screws of the mounting lug -U and +U on the insulating spacer. 10. Tighten all screws of the mounting lug -U and +U 11. Replace the covers. ® Operating Instructions – MOVIDRIVE MDX60B/61B...
  • Page 64 Installation Installation instructions for the basic unit 4Q DLZ14B DC link adapter The DC link adapter 4Q DLZ14B (part no.: 18227287) can be used to provide a DC link connection at the bottom of the device: 9007201531075595 1. Loosen the 4 screws of the upper cover and remove it. 2.
  • Page 65 Installation Installation instructions for the basic unit Side panel for DC link coupling To connect 2 devices via the DLZ11B or DLZ31B DC link coupling side by side, the ® side panel of MOVIDRIVE must be opened. ® Proceed as follows to prepare MOVIDRIVE for the side-by-side connection: CAUTION Sharp edges...
  • Page 66 Installation Installation instructions for the basic unit DLZ11B DC link coupling You can use the DLZ11B DC link coupling to connect 2 size 7 devices side by side. The DLZ11B DC link coupling is available in three different lengths: • 100 mm (part number: 18231934) •...
  • Page 67 Installation Installation instructions for the basic unit • Tip the DC link connection into the second device from above 9007201531079435 • Insert the 200  mm and 300  mm DC link connection into the one device skewed up to the stop. ®...
  • Page 68 Installation Installation instructions for the basic unit • Tip the DC link connection into the second device from above 3919719051 ® Operating Instructions – MOVIDRIVE MDX60B/61B...
  • Page 69 Installation Installation instructions for the basic unit • Screw the DC link coupling to one device first. Then attach it to the other devices. • Tighten the screws. • Replace the covers. 6. Screw the DC link coupling to one device first. Then attach it to the other devices. 7.
  • Page 70 Installation Installation instructions for the basic unit 8. Replace the covers. 9007201531079435 9. Insert the 200 mm and 300 mm DC link connection into the one device skewed up to the stop. ® Operating Instructions – MOVIDRIVE MDX60B/61B...
  • Page 71 Installation Installation instructions for the basic unit 10. Tip the DC link connection into the second device from above 3919719051 11. Screw the DC link coupling to one device first. Then attach it to the other devices. 12. Tighten the screws. ®...
  • Page 72 Installation Installation instructions for the basic unit 13. Replace the covers. DLZ31B DC link coupling To connect a device in size 7 and a smaller size side by side, you can use the DLZ31B DC link coupling (part number: 18236286): 3435514891 1.
  • Page 73 Installation Installation instructions for the basic unit 5. Mount the DC link coupling to the side panel of the size 7 device with 2 tapping screws. 3435511051 Insert the DC link connections into the devices. Observe the arrangement of the con- ductor rails depending on the mounting position.
  • Page 74 Installation Installation instructions for the basic unit Connection options per conductor rail You have the following options to connect the conductor rail: • 2 bores with a 7 mm diameter • 1 bore with an 11 mm diameter Observe the following installation notes in addition: •...
  • Page 75 Installation Installation instructions for the basic unit DLZ31B DC link coupling dimension drawing The following figure shows the dimensions of the DLZ31B DC link coupling. 265 (10.43) 219.5 (8.64) 95.5 (3.76) WARNING CAUTION HOT Surface- 10 min Risk of Burn Risk of Electric Shock 211 (8.31) 109 (4.29)
  • Page 76 Installation Installation instructions for the basic unit Conversion to motor inverter ® A MOVIDRIVE MDX61B inverter can be used as MDR62B motor inverter. The follow- ing applications can be considered: • Supply via MDR61B regenerative power supply ® • Supply via MOVIDRIVE MDX61B connection type B Proceed as follow to operate an inverter as MDX62B motor inverter: 3437047051...

  • Page 77: Removing/Installing The Keypad

    Installation Removing/installing the keypad Removing/installing the keypad 4.2.1 Removing the keypad Proceed as follows: STOP 1804920715 1. Unplug the connection cable from the XT slot. 2. Carefully push the keypad downwards until it comes off the upper fixture on the front cover.

  • Page 78: Removing/Installing The

    Installation Removing/installing the front cover Removing/installing the front cover 4.3.1 Removing the front cover Proceed as follows to remove the front cover: 1804955147 1. If a keypad is installed, remove it first. 2. Press the grooved clip on top of the front cover. 3.
  • Page 79 Installation Removing/installing the front cover 4.3.2 Installing the front cover Proceed as follows to install the front cover: BG1 - 7 1804958219 1. Insert the underside of the front cover into the support. 2. Keep the grooved clip on top of the front cover pressed down. 3.

  • Page 80: Information Regarding Ul

    Installation Information regarding UL Information regarding UL INFORMATION Due to UL requirements, the following chapter is always printed in English independ- ent of the language of the documentation. 4.4.1 Field wiring power terminals • Use 75 °C copper wire only - models with suffix 0075, 0110, 0370, 0450, 0550, 0750, 0900, 1100, 1320, 1600, 2000, 2500.
  • Page 81 Installation Information regarding UL 4.4.3 Branch circuit protection Integral solid state short circuit protection does not provide branch circuit protection. Branch circuit protection must be provided in accordance with the National Electrical Code and any additional local codes. AC 400/500 V devices Three Phase 380 V –...
  • Page 82 Installation Information regarding UL Three Phase 380 V – 500 V Voltage Range SCCR: 200 kA/ 500 V SCCR: 200 kA/ 500 V SCCR: 65 kA/ 480 V: SCCR: 65 kA/ 460 V when protected by: when protected by when protected by when protected by: Model Non Semiconductor Inverse-Time Circuit Type E Combination Motor Controller...
  • Page 83 Installation Information regarding UL 4.4.5 Ambient temperature The units are suitable for an ambient temperature of 40 °C, max. 60 °C with derated output current. To determine output current rating at higher than 40 °C, the output current should be derated 2.5 % per °C between 40 °C and 50 °C, and 3 % per °C between 50 °C and 60 °C.

  • Page 84: Shield Clamps

    Installation Shield clamps Shield clamps 4.5.1 Shield clamp for power section, size 0 ® A set of shield clamps is supplied as standard for the power section of MOVIDRIVE MDX60B/61B size 0. The shield clamps are not yet installed. Install the shield clamps for the power section as follows: •...
  • Page 85 Installation Shield clamps 4.5.2 Shield clamp for power section, size 1 ® A shield clamp is supplied as standard for the power section with MOVIDRIVE MDX61B size 1. Install this shield clamp on the power section together with the retain- ing screws of the device.
  • Page 86 Installation Shield clamps 4.5.4 Shield clamp for power section, sizes 3 to 7 ® No shield clamps for the power section are supplied with MOVIDRIVE MDX61B sizes 3  –  7. Use commercially available shield clamps for installing the shielding of motor and brake cables.
  • Page 87 Installation Shield clamps Size 1 to 7 1805401483 [1] Contact clip(s) [2] Retaining screw(s) for contact clips [3] Shield plate [4] Retaining screw for shield terminal ® Operating Instructions – MOVIDRIVE MDX60B/61B...

  • Page 88: Touch Guard For Power Terminals

    Installation Touch guard for power terminals Touch guard for power terminals WARNING Uncovered power connections. Severe or fatal injuries from electric shock. • Install the touch guard according to the regulations. • Never start the device if the touch guard is not installed. 4.6.1 Size 2S ®...
  • Page 89 Installation Touch guard for power terminals 4.6.2 Size 3 The new hardware versions of size 3 can be recognized by the entries in the status fields 2 and 5 on the nameplate of the power section. Older hardware versions do not have entries in the status fields 2 and 5.
  • Page 90 Installation Touch guard for power terminals Heat shrink tubing The size 3 inverters have degree of protection IP20 if all power cables (connections X1, X2, X3, X4) are covered with a heat shrink tubing as shown in the following illus- tration.
  • Page 91 Installation Touch guard for power terminals 4.6.3 Sizes 4 and 5 ® IP20 is achieved for MOVIDRIVE MDX61B sizes 4 and 5 (AC  500  V devices: MDX61B0370/0450/0550/0750; AC 230 V devices: MDX61B0220/0300), as soon as one of the following conditions is fulfilled: •...
  • Page 92 Installation Touch guard for power terminals For additional information on the X1, X2, X3 and X4 power terminals, refer to chapter "Technical data". ® Operating Instructions – MOVIDRIVE MDX60B/61B...
  • Page 93 Installation Touch guard for power terminals 4.6.4 Sizes 4 – 6 ® MOVIDRIVE size 4 (AC  500  V devices: MDX61B0370/0450; AC 230  V devices: MDX61B0220/0300), size (MDX61B0550/0750) size (MDX61B0900/1100/1320), two touch guards with eight retaining screws are supplied as standard. Install the touch guard on both safety covers of the power terminals. ®...
  • Page 94 Installation Touch guard for power terminals 4.6.5 Size 7 Installing the touch guard DLB21B ® Degree of protection IP20 is achieved for MOVIDRIVE MDX61B size 7 when the touch guard DLB21B (part no 18226086) is trimmed to size by the customer and mounted in front and behind the power connections.

  • Page 95: Wiring Diagrams For Basic Device

    Installation Wiring diagrams for basic device Wiring diagrams for basic device 4.7.1 Power section (sizes 0 – 6) and brake F11/F12/F13 Protective earth (shield) (AC-3) L1 L2 NF ... line filter option L1' L2' L3' DC link connection*** F14/F15 F14/F15 L1 L2 L3 F14/F15 Power section...
  • Page 96 Installation Wiring diagrams for basic device 4.7.2 Power section and DC power supply unit (size 7) For connecting the brake, refer to the wiring diagram of size 1 – 6. F11/F12/F13 F21/F22/F23 (AC-3) L1 L2 NF... line filter option L1' L2' L3' L1 L2 L3 Power section power...
  • Page 97 Installation Wiring diagrams for basic device 4.7.3 Brake rectifier in control cabinet Install the connection cables between the brake rectifier and the brake separately from other power cables when installing the brake rectifier in the control cabinet. Joint in- stallation is only permitted with shielded power cables. 4.7.4 Braking resistor BW...
  • Page 98 Installation Wiring diagrams for basic device 4.7.5 MDX60B/61B signal terminals Control unit Changeover I-signal <-> U-signal * S 11 Keypad Serial interface System bus terminating resistor S 12 option option XT: 9.6 kBaud <-> 57.6 kBaud S 13 DBG60B e.g. USB11A S 14 Frequency input active ON OFF*...
  • Page 99 Installation Wiring diagrams for basic device DGND (X10, X12, X13, X16, X17) is connected with PE as standard (tapped hole, see chapter "Device structure"). You can establish electrical isolation by removing the M4 × 14 grounding screw. When using a DCS21B/22B/S31B/32B and DEU21B option card, electrical isolation is not possible. External voltage supply via X:10 only for sizes 0 – 6.
  • Page 100 Installation Wiring diagrams for basic device 4.7.6 Description of terminal functions on the basic device (power section and control unit) Terminal Function X1:1/2/3 L1/L2/L3 (PE) Line connection X2:4/5/6 U/V/W (PE) Motor connection X3:8/9 +R/-R (PE) Braking resistor connection (PE) DC link connection 9,10,11,12 L1/L2/L3/PE Connection of switched-mode power supply (only for size 7)
  • Page 101 Installation Wiring diagrams for basic device Terminal Function X10:9 VI24 Input DC+24 V voltage supply (backup voltage depending on options, unit diagnosis when supply system off) X10:10 DGND Reference potential for binary signals Information on X:10.9: Only connect external backup voltage DC +24 V to sizes 0 – 6. With size 7, the DC power supply unit must be connected to the supply system.

  • Page 102: Assignment Of Braking Resistors, Chokes And Filters

    Installation Assignment of braking resistors, chokes and filters Assignment of braking resistors, chokes and filters 4.8.1 AC 400/500 V devices, size 0 ® MOVIDRIVE MDX60/61B...-5A3 0005 0008 0011 0014 Size Braking resistors Tripping current Part number Part number BW... / BW...
  • Page 103 Installation Assignment of braking resistors, chokes and filters 4.8.2 AC 400/500 V devices, sizes 1, 2S, and 2 ® MOVIDRIVE MDX61B...-5A3 0015 0022 0030 0040 0055 0075 0110 Size Braking resistors Tripping current Part number Part number BW... / BW..-..-T BW...
  • Page 104 Installation Assignment of braking resistors, chokes and filters 4.8.3 AC 400/500 V devices, sizes 3 and 4 ® MOVIDRIVE MDX61B...-503 0150 0220 0300 0370 0450 Size Braking resistors Tripping current Part number Part number Part number BW... / BW... BW...-...-T BW...-...-P BW...-...-T BW...-...-P...
  • Page 105 Installation Assignment of braking resistors, chokes and filters 4.8.4 AC 400/500 V devices, sizes 5 – 7 ® MOVIDRIVE MDX61B...-503 0550 0750 0900 1100 1320 1600 2000 2500 Size Braking resistors Tripping current Part number BW...-...-T BW...-...-T BW106-T = 47.4 A 18200834 BW206-T = 54.8 A 18204120 BW1.4-170 = 110 A 13301527...
  • Page 106 Installation Assignment of braking resistors, chokes and filters 4.8.5 AC 230 V devices, sizes 1 – 4 ® MOVIDRIVE MDX61B...-2_3 0015 0022 0037 0055 0075 0110 0150 0220 0300 Size Braking resistors Tripping current Part number Part number BW...-.../ BW... BW...-...-T BW...-...-T BW...-...-P BW039-003 = 2.7 A...

  • Page 107: Connecting The System Bus (Sbus 1)

    Installation Connecting the system bus (SBus 1) Connecting the system bus (SBus 1) Max. 64 CAN bus stations can be addressed via system bus (SBus). Use a repeater after 20 or 30 stations, depending on the length of the cables and the cable capacit- ance.
  • Page 108 Installation Connecting the system bus (SBus 1) Connecting the shield • Connect the shield to the electronics shield clamp on the inverter or the master controller and make sure it is connected over a wide area at both ends. Cable length •...

  • Page 109: Connecting The Rs485 Interface

    Installation Connecting the RS485 interface 4.10 Connecting the RS485 interface The RS485 interface (X13:ST11, ST12) can be used for connecting max. 32 ® ® MOVIDRIVE devices, e.g. for master/slave operation, or 31 MOVIDRIVE devices and a higher-level controller (PLC). The baud rate is set to 9.6 baud by default. 4.10.1 Wiring diagram of the RS485 interface (X13) X13:...

  • Page 110: Connecting The Dwe11B/12B Interface Adapter

    Installation Connecting the DWE11B/12B interface adapter 4.11 Connecting the DWE11B/12B interface adapter 4.11.1 Part number and description • DWE11B, part number 01881876 The interface adapter DWE11B (HTL  →  TTL) in the form of an adapter cable is used to connect single-ended HTL encoders to the DEH11B/DEH21B options. Only the A, B and C tracks are connected.

  • Page 111: Connecting The Uws21B Interface Adapter (Rs232 ↔ Rs485)

    Installation Connecting the UWS21B interface adapter (RS232 ↔ RS485) 4.12 Connecting the UWS21B interface adapter (RS232 ↔ RS485) 4.12.1 Part number Interface adapter option UWS21B: 18204562 4.12.2 Scope of Delivery The scope of delivery for the UWS21B option includes: • UWS21B device ®...
  • Page 112 Installation Connecting the UWS21B interface adapter (RS232 ↔ RS485) 4.12.4 Connecting UWS21B to PC • Use the connection cable supplied (shielded RS232 standard interface cable) to connect the UWS21B option to the PC. • The following figure shows the connection cable between UWS21B and PC (1:1 connection).

  • Page 113: Connecting The Usb11A Interface Adapter

    Installation Connecting the USB11A interface adapter 4.13 Connecting the USB11A interface adapter 4.13.1 Part number Interface adapter option USB11A: 08248311 4.13.2 Scope of Delivery • The scope of delivery for the USB11A includes: – USB11A interface adapter – USB connection cable PC – USB11A (type USB A-B) ®...
  • Page 114 Installation Connecting the USB11A interface adapter 4.13.4 Installation ® • Connect the USB11A to a PC and MOVIDRIVE MDX60B/61B using the connec- tion cables supplied. • Insert the enclosed CD into the CD drive of your PC and install the driver. The first free COM port on the PC will be assigned to the USB11A interface adapter.

  • Page 115: Option Combinations For Mdx61B

    Installation Option combinations for MDX61B 4.14 Option combinations for MDX61B 4.14.1 Configuration of option slots Size 0 (0005 – 0014) Size 1 – 6 (0015 – 1320) 1806023691 [1] Encoder slot for encoder options [2] Fieldbus option slot for communication options [3] Expansion slot for communication options (only sizes 1 – 6) ®...
  • Page 116 Installation Option combinations for MDX61B 4.14.2 Option card combinations for MDX61B The option cards are different sizes and can only be installed in the matching option slots. Fieldbus interfaces including DHx cannot be combined with one another. The ® following list shows the possible combinations of option cards for MOVIDRIVE MDX61B.
  • Page 117 Installation Option combinations for MDX61B ® Option card Designation MOVIDRIVE MDX61B Encoder slot Fieldbus slot Expansion slot Size 0 – size 7 Size 0 – size 7 Size 1 – size 7 ® DHR41B User-programmable MOVI-PLC advanced controller DHP11B + DHP11B + OST11B (RS485 inter- OST11B DHP11B...

  • Page 118: Installing And Removing Option Cards

    Installation Installing and removing option cards 4.15 Installing and removing option cards INFORMATION ® • For MOVIDRIVE MDX61B size 0, only SEW-EURODRIVE is authorized to in- stall or remove option cards. ® • For MOVIDRIVE MDX61B sizes 1 – 7, you can install or remove the option cards yourself.
  • Page 119 Installation Installing and removing option cards 4.15.2 Basic procedure for installing/removing an option card ® The following figure shows the installation of an option card in MOVIDRIVE MDX61B sizes 1 – 7. 9007201196765451 1. Remove the retaining screws holding the card retaining bracket. Pull the card re- taining bracket out evenly from the slot (do not twist!).

  • Page 120: Connecting Encoders And Resolvers

    Installation Connecting encoders and resolvers 4.16 Connecting encoders and resolvers INFORMATION Folgen • The following wiring diagrams do not show the view onto the cable end but the ® view onto the connection to motor or MOVIDRIVE • The core colors specified in the wiring diagrams are in accordance with IEC 757 and correspond to the core colors used in the prefabricated cables from SEW‑EURODRIVE.
  • Page 121 Installation Connecting encoders and resolvers 4.16.2 Shield contact Connect the shield of the encoder/resolver cable over a large area. On the inverter Connect the shield on the inverter end in the housing of the D-sub connector (→ fol- lowing figure). 2286956939 On the encoder/resolver Connect the shield on the encoder/resolver side at the respective grounding clamps...

  • Page 122: Connection And Terminal Description Of The Deh11B Option (Hiperface ® )

    Installation Connection and terminal description of the DEH11B (Hiperface) option Connection terminal description of the DEH11B (Hiperface) option ® 4.17 Connection and terminal description of the DEH11B option (HIPERFACE 4.17.1 Part number ® Option HIPERFACE encoder card type DEH11B: 08243107 INFORMATION ®...
  • Page 123 Installation Connection and terminal description of the DEH11B (Hiperface) option 4.17.2 Permissible encoders at X:14 Refer to chapter "Connecting external encoders to X:14" (→ 2 129). 4.17.3 Permissible encoders at X:15 The following SEW‑EURODRIVE encoders can be connected to the option ® HIPERFACE encoder card type DEH11B: ®...

  • Page 124: Connection And Terminal Description Of The Deh21B Option

    Installation Connection and terminal description of the DEH21B option 4.18 Connection and terminal description of the DEH21B option 4.18.1 Part number Encoder card option DEH21B: 18208185 INFORMATION ® • For detailed information on the DEH21B option, refer to the manual "MOVIDRIVE MDX61B DIP11B/DEH21B absolute encoder cards".

  • Page 125: Connection And Terminal Description Of The Deu21B Option

    Installation Connection and terminal description of the DEU21B option 4.19 Connection and terminal description of the DEU21B option 4.19.1 Part number Multi-encoder card option type DEU21B: 01822696 INFORMATION ® • For detailed information on the DEU21B option, refer to the "MOVIDRIVE MDX61B multi-encoder card DEU21B"...
  • Page 126 Installation Connection and terminal description of the DEU21B option INFORMATION • If X14 is used as an incremental encoder simulation output, the switchover (X14:7) must be jumpered with DGND (X14:8). ® • The 24  V encoders from SEW-EURODRIVE (except HTL and HIPERFACE have a wide voltage range (DC ...

  • Page 127: Connection And Terminal Description Of The Der11B (Resolver) Option

    Installation Connection and terminal description of the DER11B (resolver) option 4.20 Connection and terminal description of the DER11B (resolver) option 4.20.1 Part number Resolver card option type DER11B: 08243077 INFORMATION ® • The DEU21B, DER11B option can be installed in MOVIDRIVE MDX61B sizes 0 – 7.
  • Page 128 Installation Connection and terminal description of the DER11B (resolver) option 4.20.3 Resolver at X:15 2-pole resolvers, AC 7 V, 7 kHz, can be connected at X15 (resolver input). The gear ratio of the resolver amplitudes must be approximately 0.5 ± 10%. The control dynam- ics decrease if the value is lower;...

  • Page 129: Connecting External Encoders To X:14

    Installation Connecting external encoders to X:14 4.21 Connecting external encoders to X:14 4.21.1 External encoder at DEH11B, DEU21B and DER11B (X:14) The following external encoders can be connected to connector X14 of the DEH11B option and the DER11B option: ® External encoder at DEH11B and DER11B - MOVIDRIVE (X:14) ®...

  • Page 130: Connection Of Encoder Options

    Installation Connection of encoder options 4.22 Connection of encoder options 4.22.1 Connection of DEH11B option Encoder connection at X:15 Depending on the motor type and motor configuration, the encoder is connected via plug connector or terminal box. DR71 – 315 Connect the encoder to the option DEH11B as follows: max.
  • Page 131 Installation Connection of encoder options CM71 – 112 with terminal box ® Connect the HIPERFACE encoder to the DEH11B option as follows: max. 100 m A..H / E..H DEH11B, X15: cos+ cos- sin+ sin- DATA- DATA+ TF/TH/KTY+/PK TF/TH/KTY-/PK GYPK RDBU 9007201060812171 ® Operating Instructions –...
  • Page 132 Installation Connection of encoder options Connection of sin/cos and TTL encoders (DC 24 V) The high resolution sin/cos encoders and TTL encoders with DC 24 V supply can also be connected to DEH11B. Proceed as follows to connect sin/cos encoders and TTL encoders with DC 24 V supply to the DEH11B option: max.
  • Page 133 Installation Connection of encoder options 4.22.2 Connection of DER11B (resolver) option to X:15 Terminal assignment/pin assignment CM.. motors: The resolver connections are located in a plug connector or on a 10-pin Wago terminal strip. Plug connector CM..: Intercontec, type ASTA021NN00 10 000 5 000 Terminal/pin Description Core color in prefabricated cable...
  • Page 134 Installation Connection of encoder options 4.22.3 Connection of external encoders to the DEH11B and DER11B options Voltage supply SEW-EURODRIVE encoders with DC 24 V voltage supply (max. DC 180 mA) are con- nected directly to X14. These SEW-EURODRIVE encoders are then powered by the inverter.
  • Page 135 Installation Connection of encoder options Connection of sin/cos and TTL encoders (DC 24 V) Proceed as follows to connect sin/cos encoders and TTL encoders with DC 24 V sup- ply: DEH11B/DER11B, EH1S / EH1R / ES1S / ES1R max. 100 m X14: EV1S / EV1R / ES2R / ES2S 1806336395...

  • Page 136: Connection Of Incremental Encoder Simulation

    Installation Connection of incremental encoder simulation 4.23 Connection of incremental encoder simulation 4.23.1 Incremental encoder emulation Connector X14 of the DEH11B or DER11B option can also be used as the incremental encoder simulation output. For this purpose, you must jumper "switchover" (X14:7) with DGND (X14:8).

  • Page 137: Master/Slave Connection

    Installation Master/slave connection 4.24 Master/slave connection 4.24.1 Master/slave connection Connector X14 of the DEH11B, DEU21B or DER11B option can also be used for the "internal synchronous operation" application (master/slave connection of several ® MOVIDRIVE devices). For this purpose, you must jumper "switchover" (X14:7) with DGND (X14:8) on the master end.

  • Page 138: Connection And Terminal Description Of The Dio11B Option

    Installation Connection and terminal description of the DIO11B option 4.25 Connection and terminal description of the DIO11B option 4.25.1 Part number Option input/output card type DIO11B: 08243085 INFORMATION • The "input/output card type DIO11B" option is only possible in conjunction with ®...
  • Page 139 Installation Connection and terminal description of the DIO11B option The following figure shows voltage input 24VIN (X23:9) and reference potential DGND (X22:10). DIO11B DGND 24VIN 1806364811 4.25.3 Voltage input n2 The analog setpoint input n2 (AI21/22) can be used as a differential input or as an in- put with AGND reference potential.
  • Page 140 Installation Connection and terminal description of the DIO11B option 4.25.5 Voltage outputs AOV1 and AOV2 Assign the analog voltage outputs AOV1 and AOV2 in accordance with the following figure: DIO11B DIO11B AI21 AI21 AI22 AI22 AGND AGND AOV1 AOV1 AOC1 AOC1 AGND AGND...

  • Page 141: Connection And Terminal Description Of The Dfc11B Option

    Installation Connection and terminal description of the DFC11B option 4.26 Connection and terminal description of the DFC11B option 4.26.1 Part number CAN-Bus interface option type DFC11B: 08243174 INFORMATION ® • The "CAN bus interface type DFC11B" option can only be used with MOVIDRIVE MDX61B, not with MDX60B.

  • Page 142: Startup

    Startup General startup instructions Startup General startup instructions WARNING Uncovered power connections. Severe or fatal injuries from electric shock. • Install the touch guard according to the regulations. • Never start the device if the touch guard is not installed. 5.1.1 Prerequisite The drive must be configured correctly to ensure that startup is successful.
  • Page 143 Startup General startup instructions 5.1.4 Motor/inverter combinations The following tables indicate which inverter/motor combinations this applies to. 400/500 V devices ® MOVIDRIVE MDX60/61B SEW-EURODRIVE motor In operating mode VFC 0005-5A3-4 DRN80M4 0008-5A3-4 DRN80M4 0011-5A3-4 DRN90S4 0014-5A3-4 DRN90L4 0015-5A3-4 DRN90L4 0022-5A3-4 DRN100LS4 0030-5A3-4 DRN100L4 0040-5A3-4...
  • Page 144 Startup General startup instructions 230 V devices ® MOVIDRIVE MDX60/61B SEW-EURODRIVE motor In operating mode VFC 0015-2A3-4 DRN90L4 0022-2A3-4 DRN100LS4 0037-2A3-4 DRN112M4 0055-2A3-4 DRN132S4 0075-2A3-4 DRN132M4 0110-203-4 DRN160M4 0150-203-4 DRN160L4 0220-203-4 DRN180L4 0300-203-4 DRN200L4 5.1.5 Lifting applications WARNING Danger of fatal injury if the hoist falls. Severe or fatal injuries.

  • Page 145: Preliminary Work And Resources

    Startup Preliminary work and resources Preliminary work and resources • Check the installation. • Performing startup with the DBG60B keypad: WARNING Risk of crushing if the motor starts up unintentionally. Severe or fatal injuries. • Ensure that the motor cannot start inadvertently, for  example, by removing the electronics terminal block X13.

  • Page 146: Startup With Dbg60B Keypad

    Startup Startup with DBG60B keypad Startup with DBG60B keypad 5.3.1 General information Startup with the DBG60B keypad is only possible in operating modes VFC and V/f. Startup in CFC and SERVO operating modes is only possible using the ® MOVITOOLS MotionStudio engineering software.
  • Page 147 Startup Startup with DBG60B keypad 5.3.2 Choose the required language The following text appears on the display when the keypad is switched on for the first time or after activating the start mode: EURODRIVE The symbol for language selection then appears on the display. 1810055819 Proceed as follows to select the language: •...
  • Page 148 Startup Startup with DBG60B keypad 5.3.3 Startup The figure below shows the keys required for startup. 1810058891 Move up to the next menu item Confirm entry Activate the context menu Move down to the next menu item Change the menu, display mode ↔ edit mode Cancel or abort startup ®...
  • Page 149 Startup Startup with DBG60B keypad 5.3.4 Startup procedure INFORMATION This example refers to a 400 V device. 1. "0" signal at terminal X13:1 (DIØØ "/CONTROL.IN- 0.00rpm HIBIT"), e.g. by disconnecting the electronics terminal 0.000Amp block X13. CONTROLLER IN- HIBIT 2. Press the key to activate the context menu.
  • Page 150 Startup Startup with DBG60B keypad 8. Select the operating mode you require. Press the C36*OPER.MODE key to choose the next parameter. SPEED CONTROL HOIST 9. Select the motor type. If the motor is not listed, select C02*MOTOR TYPE the list "THIRD-PARTY MOTOR". DRN80M42 Press the key to choose the next parameter.
  • Page 151 Startup Startup with DBG60B keypad 12. Enter the following motor nameplate data: • C10* nominal motor current, note the connection type (W or m). • C11* nominal motor power • C12* power factor cos φ • C13* nominal motor speed 13.
  • Page 152 Startup Startup with DBG60B keypad 19. Press the SIGNATURE key to scroll down until the menu item "EXIT" is selected. QUIT BASIC VIEW 20. Confirm your selection using the 0.00rpm key. The basic dis- play appears. 0.000Amp CONTROLLER IN- HIBIT ®...
  • Page 153 Startup Startup with DBG60B keypad 5.3.5 Starting up the speed controller Startup is performed without the speed controller first (→ Section "Startup procedure, steps 1 through 17"). 1. The selected operating mode is displayed. If the set- C00*STARTUP ting is correct, go to the next menu item. PARAMETER SET VFC n-control 2.
  • Page 154 Startup Startup with DBG60B keypad 6. Enter the moment of inertia of the brake and fan. D00* J BRAKE+FAN 1.000 7. Enter the mass moment of inertia of the load (gear unit C20* 10e–4kgm + driven machine) extrapolated for the motor shaft. LOAD MOMENT OF INERTIA 0.200...
  • Page 155 Startup Startup with DBG60B keypad – In the context menu, select the menu item "PARAMETER MODE". Select para- ® meter P807 "MDX → DBG". The parameter set is copied from MOVIDRIVE the DBG60B. ® • The parameter set can now be copied to other MOVIDRIVE devices using the DBG60B.

  • Page 156: Operation Of Movitools Motionstudio

    Startup Operation of MOVITOOLS® MotionStudio Operation of MOVITOOL S® MotionStud ® Operation of MOVITOOLS MotionStudio ® 5.4.1 About MOVITOOLS MotionStudio Jobs The software package enables you to perform the following tasks with consistency: • Establishing communication with devices • Executing functions of the devices Establishing communication with devices ®...
  • Page 157 Startup Operation of MOVITOOLS® MotionStudio Online help After installation, the following types of help are available to you: • The documentation is displayed in a help window after you start the software. If the help window does not appear at the start, deactivate the "Display" check box, in the menu under [Settings] / [Options] / [Help].
  • Page 158 Startup Operation of MOVITOOLS® MotionStudio 5.4.2 First steps Starting the software and creating the project ® To start MOVITOOLS MotionStudio and create a project, proceed as follows: ® 1. Start the MOVITOOLS MotionStudio from the Windows start menu via: [Start]  /  [Programs]  /  [SEW]  /  [MOVITOOLS MotionStudio]  /  [MOVITOOLS MotionStudio] 2.
  • Page 159 Startup Operation of MOVITOOLS® MotionStudio Startup for HTL motor encoders Adhere to the following startup instructions with DEH11/21B for starting an HTL motor ® encoder (except DEU21B) on MOVIDRIVE MDX61B. 1810081419 "SEW encoder type" drop-down list "Encoder type" drop-down list "PPR count"...

  • Page 160: Starting The Motor

    Startup Starting the motor Starting the motor 5.5.1 Analog setpoint input The following table shows the signals that must be present on terminals X11:2 (AI1) and X13:1 – X13:6 (DIØØ – DIØ5) when the "UNIPOL/FIX.SETPT" setpoint is selec- ted (P100) to operate the drive with an analog setpoint input. Function X11:2 X13:1...
  • Page 161 Startup Starting the motor 5.5.2 Travel diagram The following travel diagram shows by way of example how the motor is started with the wiring of terminals X13:1 – X13:4 and analog setpoints. Digital output X10:3 (DBØØ "/Brake") is used for switching braking contactor K12. "1"...
  • Page 162 Startup Starting the motor 5.5.3 Fixed setpoints The following table shows the signals that must be present on terminals X13:1 – X13:6 (DIØØ – DIØ5) when the "UNIPOL/FIX.SETPT" setpoint is selected (P100) to operate the drive with the fixed setpoints. Function X13:1 X13:2...
  • Page 163 Startup Starting the motor 5.5.4 Travel diagram The following travel diagram shows an example of how the drive is started with the wiring of terminals X13:1 – X13:6 and internal fixed setpoints. Digital output X10:3 (DBØØ "/Brake") is used for switching braking contactor K12. "1"...
  • Page 164 Startup Starting the motor 5.5.5 Manual operation ® The inverter can be controlled using the DBG60B keypad/MOVITOOLS MotionStudio in manual operation (context menu → manual operation). The 7-segment display on the unit shows "H" during manual operation. The digital inputs are then without any functions for the duration of manual operation, with the exception of X13:1 (DIØØ...
  • Page 165 Startup Starting the motor 5.5.6 Startup in operating mode "VFC & flying start function" The parameter P320 Automatic adjustment is deactivated in the mode "VFC & Flying start function". It is important that the stator resistance (P322 IxR compensation 1) is set correctly to ensure that the flying start function is performed properly.

  • Page 166: Complete Parameter List

    Startup Complete parameter list Complete parameter list 5.6.1 General information • The parameters contained in the standard user menu are marked by a "\" (= dis- play on the DBG60B keypad). • The factory setting for the parameter is highlighted in bold. 5.6.2 Display values Par.
  • Page 167 Startup Complete parameter list Par. Name Factory setting Digital input DIØ1 Not in DBG60B Digital input DIØ2 Digital input DIØ3 Digital input DIØ4 Digital input DIØ5 Digital input DIØ6 Digital input DIØ7 \039 Status of digital inputs DIØØ – DIØ7 Digital input options Digital input DI1Ø...
  • Page 168 Startup Complete parameter list Par. Name Factory setting Device type Nominal output current Option 1 encoder slot Option 2 fieldbus slot Option 3 expansion slot Basic device firmware DBG firmware Only in DBG60B Technology function Device design Standard technology Fault memory \080 Errors t-0 Errors t-1...
  • Page 169 Startup Complete parameter list 5.6.3 Parameters Par. Name Setting range Factory setting Selectable par. Parameter set 1/2 Setpoints/ramp generators Setpoint selection \100 Setpoint source Bipolar/fixed setpoint Unipolar/fixed setpoint RS485/fixed setpoint Fieldbus Motor potentiometer/fixed setpoint Motor potentiometer + analog setpoint Fixed setpoint + AI01 Fixed setpoint * AI01 Master SBus 1 Master RS485...
  • Page 170 Startup Complete parameter list Par. Name Setting range Factory setting Selectable par. Parameter set 1/2 Stop ramp t23 0 – 2 – 20 s Emergency stop ramp t24 0 – 2 – 20 s Ramp monitoring 2 Motor potentiometer (parameter sets 1 and 2) Ramp t3 up 0.2 – 20 – 50 s Ramp t3 down 0.2 – 20 – 50 s Save last Save...
  • Page 171 Startup Complete parameter list Par. Name Setting range Factory setting Selectable par. Parameter set 1/2 Master encoder PPR count 128/256/512/1024/2048 Synchronous operation with catch up Synchronous speed 0 – 1500 – 6000 min Synchronous ramp 0 – 2 – 50 s Process controller parameter Operating mode Controller off/control/step response Cycle time 1/5/10 ms The current is No response/Move closer to setpoint...
  • Page 172 Startup Complete parameter list Par. Name Setting range Factory setting Selectable par. Parameter set 1/2 350/351 Change direction of rotation 1/2 Terminal (only in parameter set 1) Startup (only available in DBG60B) Startup Yes/No Reference signals Speed reference message Speed reference value 0 – 1500 – 6000 min Hysteresis 0 – 100 – 500 min...
  • Page 173 Startup Complete parameter list Par. Name Setting range Factory setting Selectable par. Parameter set 1/2 X42 Encoder monitoring X42 Pulse count monitoring Power off monitoring Power off response time 0 – 5 s Mains OFF response Controller inhibit Emergency stop Phase failure monitoring Motor thermal protection Sensor type 1 No sensor...
  • Page 174 Startup Complete parameter list Par. Name Setting range Factory setting Selectable par. Parameter set 1/2 Digital input DIØ2 CCW/stop Digital input DIØ3 Enable/stop Digital input DIØ4 n11/n21 Digital input DIØ5 n12/n22 Digital input DIØ6 No function Digital input DIØ7 No function Digital inputs option Digital input DI1Ø...
  • Page 175 Startup Complete parameter list Par. Name Setting range Factory setting Selectable par. Parameter set 1/2 Operating mode 1 VFC 1 VFC 1 & GROUP VFC 1 & HOIST VFC 1 & DC BRAK. VFC 1 &FLY.START VFC n-control VFC-n-CTRL&GRP. VFC-n-CTRL&HOIST VFC-n-CTRL.&SYNC.
  • Page 176 Startup Complete parameter list Par. Name Setting range Factory setting Selectable par. Parameter set 1/2 Locking Run/Stop keys Energy-saving function Energy-saving function Ethernet configuration IP address 000.000.000.000 – 192.168.10.4 – 223.255.255.255 Subnet mask 000,000,000,000 – 255,255,255,000 – 223,255,255,255 Default gateway 000.000.000.000 – 223.255.255.255 Baud rate Display value that cannot be changed (0 – 100 – 1000 MBaud) MAC address Display value that cannot be changed (00-0F-69-XX-XX-XX) EtherNet/IP™...
  • Page 177 Startup Complete parameter list Par. Name Setting range Factory setting Selectable par. Parameter set 1/2 Modulation 860/861 PWM frequency 1/2 VFC 2.5 kHz 4 kHz 8 kHz 12 kHz 16 kHz 862/863 PWM fix 1/2 PWM frequency CFC 2.5 kHz 4 kHz 8 kHz 16 kHz Process data description Setpoint description PO1...
  • Page 178 Startup Complete parameter list Par. Name Setting range Factory setting Selectable par. Parameter set 1/2 Ramp type Linear Square Sine Bus ramp Jerk-limited Electronic cam I-synchronous operation Cross Cutter Speed interpolation Position interpolation 12 bit Position interpolation 16 bit Ramp mode Mode 1 Mode 2 Mode 3 Bus setpoint source...
  • Page 179 Startup Complete parameter list Par. Name Setting range Factory setting Selectable par. Parameter set 1/2 Module denominator 1 – (2  – 1) Modulo encoder resolution 0 – 4096 – 20000 IPOS synchronization DRAM synchronization Yes/No Synchronization phase -2 – 0 – 2 ms ® Operating Instructions – MOVIDRIVE MDX60B/61B...

  • Page 180: Operation

    Operation Operating displays Operation Operating displays 6.1.1 7-segment display ® The 7-segment display shows the operating condition of MOVIDRIVE and, in the event of an error, an error or warning code. 7-segment dis- Device status Meaning play (high byte in status word 1) 24 V operation (inverter not ready) Controller inhibit active...
  • Page 181 Operation Operating displays 6.1.2 DC link voltage display of size 7 INFORMATION The DC link voltage display goes out about 20 seconds after the power off. 6.1.3 DBG60B keypad Basic displays: 0.00rpm Display when X13:1 (DIØØ "/controller inhibit") = "0". 0.000Amp CONTROLLER IN- HIBIT...

  • Page 182: Information Messages

    Operation Information messages Information messages ® Information messages on the DBG60B (ca. 2 s in duration) or in MOVITOOLS MotionStudio (message that can be acknowledged): Text DBG60B/ Description MotionStudio ILLEGAL INDEX Index addressed via interface not available. NOT IMPLEMENT. • Attempt to execute a non-implemented function.

  • Page 183: Functions Of The Dbg60B Keypad

    Operation Functions of the DBG60B keypad Functions of the DBG60B keypad 6.3.1 Key assignments for DBG60B [12] [11] [10] 1810609803 Stop STOP Up arrow, moves up to the next menu item Start OK, confirms the entry Activate the context menu Down arrow, moves down to the next menu item Decimal point Sign reversal...
  • Page 184 Operation Functions of the DBG60B keypad 6.3.2 Copy function of the DBG60B The DBG60B keypad can be used for copying complete parameter sets from one ® ® MOVIDRIVE device to other MOVIDRIVE devices. Proceed as follows: • In the context menu, select the menu item "COPY TO DBG". Confirm your selec- tion using the key.
  • Page 185 Operation Functions of the DBG60B keypad 7. Use the \ 132 s key to select the desired parameter. The flashing cursor is positioned under the third digit T11 UP CCW of the parameter number. 0.13 CONTROLLER IN- HIBIT 8. Press the \ 132 s key to activate the setting mode for the selected parameter.
  • Page 186 Operation Functions of the DBG60B keypad 6.3.4 Variable mode H... variables are displayed in the variable mode. To call up the variable mode, pro- ceed as follows: • Press the key to call up the context menu. Select the "VARIABLE MODE" menu item and confirm with the key The variable mode display appears.
  • Page 187 Operation Functions of the DBG60B keypad 6.3.6 Wake-up parameter The wake up parameter is the parameter that is displayed when the DBG60B is switched on. The factory setting for the wake up parameter is the basic display. You can select which parameter should be the wake up parameter. The following options can be used as the wake up parameter: •...

  • Page 188: Memory Card

    Operation Memory card Memory card The pluggable memory card is installed in the basic unit. The basic data is stored on the memory card and is always up-to-date. If a unit has to be replaced, the system/ machine can be operated again quickly without a PC and data backup simply by replugging the memory card.

  • Page 189: Service

    Service Damages to the device Service Damages to the device If necessary, all components of the device are replaced. Only SEW‑EURODRIVE is authorized to perform repairs. Fault information 7.2.1 Fault memory The fault memory (P080) stores the last 5 fault messages (faults t-0 – t-4). The oldest fault message is deleted whenever more than 5 fault messages have occurred.
  • Page 190 Service Fault information 7.2.3 Reset A fault message can be acknowledged as follows: • Switch the supply system off and on again – Observe a minimum switch-off time of 10 s for the line contactor K11 • Reset via input terminals, i.e. via an appropriately assigned digital input (DIØ1  –  DIØ7 with the basic device, DI1Ø – DI17 with the DIO11B option) ®...

  • Page 191: Fault Messages And List Of Faults

    Service Fault messages and list of faults Fault messages and list of faults 7.3.1 Fault message via 7-segment display The fault code is shown in a 7-segment display. The following display sequence is used (e.g. fault code 100): 1939352587 Flashing, about 1 s Display off, about 0.2 s Hundreds (if available), ca.
  • Page 192 Service Fault messages and list of faults 7.3.3 Fault list The factory set fault response is listed in the "Response P" column. (P) indicates that PLUS® the response is programmable (via P83_fault response or with IPOS ). In the event of fault 108, (P) indicates that the response can be programmed via P555 DCS fault response.
  • Page 193 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure Speed monit- Immediate Inverter in current limiting • Speed controller or current • Reduce load oring stop (P) or in slip limit controller (in VFC operating •...
  • Page 194 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure Encoder Immediate Encoder not connected, • Encoder cable or shield not • Check encoder cable and stop defective encoder, defect- connected correctly. shield for correct connec- ive encoder cable •...
  • Page 195 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure No limit Emergency Limit switches missing or • Wire break/both limit • Check wiring of limit switches stop wire break switches missing switches •...
  • Page 196 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure Reference Immediate "Reference travel" fault • The reference cam is miss- • Check reference cam travel stop (P) ing or does not switch •...
  • Page 197 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure Initialization Immediate General fault during initial- • No parameters set for • Restore the factory set- stop ization EEPROM in power section tings. Contact the SEW set incorrectly Service for advice if the Data bus fault during RAM...
  • Page 198 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure "Encoder for rapid stop 1 X15: Track signal fault • Encoder cable or shield not • Check encoder cable and communica- connected correctly shield for correct connec- Data line fault tion"...
  • Page 199 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure Open output Immediate Output open with "VFC Only in "VFC hoist" mode: • Check connection between stop hoist" • Two or all output phases are inverter and motor interrupted.
  • Page 200 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure CRC fault Immediate "CRC via internal flash" Internal device fault flash Sending in a device for repair stop fault memory defective. PLUS® PLUS® IPOS ramp Immediate "Ramp calculation"...
  • Page 201 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure DCS fault Display fault 11 The unit's ambient temper- Temperature at the place of Check the ambient tempera- ature is not in the defined operation is not in the permitted ture range...
  • Page 202 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure DCS fault Display fault 32 The range check of the ac- Faulty configuration data of the • Reload the configuration cess data is faulty. device description.
  • Page 203 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure DCS fault Display fault 35 ESS range check is faulty. Faulty configuration data of the • Undo the changes in the ESS function. ESS configuration or enter new values.
  • Page 204 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure DCS fault Display fault 38 ZSC range check is faulty. Faulty configuration data of the • Undo the changes in the ZSC function. ZSC configuration or enter new values.
  • Page 205 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure DCS fault Display fault 41 JSS range check is faulty. Faulty configuration data of the • Undo the changes in the JSS function. JSS configuration or enter new values.
  • Page 206 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure DCS fault Display fault 44 Digital output range check Faulty configuration data of di- • Undo the changes in the is faulty. gital outputs. disconnection matrix of the digital outputs or enter new values.
  • Page 207 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure DCS fault Display fault 47 Encoder scaling range Incorrectly configured encoder • Undo changes made to the check is faulty. distance. encoder distance (measur- ing length, resolution or max.
  • Page 208 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure DCS fault Display fault 50 Fault during internal data • Replace DCS..B option. transmission. • Send faulty DCS..B option with fault number to SEW‑EURODRIVE for fault diagnostics.
  • Page 209 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure DCS fault Display fault 74 Runtime fault. • Replace DCS..B option. • Send faulty DCS..B option with fault number to SEW‑EURODRIVE for fault diagnostics.
  • Page 210 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure DCS fault Display fault 103 Internal processing fault • Replace DCS..B option. PROFIsafe. • Send faulty DCS..B option with fault number to SEW‑EURODRIVE for fault diagnostics.
  • Page 211 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure DCS alarm Display fault 0 DCS alarm Communication fault back- The DCS..B option does not re- • Check hardware connection ® ® plane bus MOVIDRIVE  B.
  • Page 212 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure DCS alarm Display fault 10 Pulse 1 plausibility fault at The configured pulse 1 voltage • Check configuration of the digital input DI5. is not present at digital input DI5 digital input according DI5 (X81:7).
  • Page 213 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure DCS alarm Display fault 26 Pulse 2 plausibility fault at The configured pulse 2 voltage • Check configuration of the digital input DI5. is not present at digital input DI5 digital input according DI5 (X81:7).
  • Page 214 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure DCS alarm Display fault 42 Plausibility fault incorrect The current acceleration ex- • Check the configuration acceleration. ceeds the configured maximum (encoder screen: max. set acceleration.
  • Page 215 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure DCS alarm Display fault 74 Faulty switching behavior DC 0 V short circuit at digital Check wiring at digital output. of the low-side driver output DO1_M (X82:4).
  • Page 216 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure DCS alarm Display fault 114 Faulty switching behavior DC 24 V short circuit at digital Check wiring at digital output. of the high-side driver output DO2_P (X83:1).
  • Page 217 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure DCS alarm Display fault 146 Voltage supply of encoder The voltage supply of the en- • Overload in the supply faulty (E3405 = encoder 1 coder is not within the defined voltage of the encoder;...
  • Page 218 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure "Ex-e protec- Emergency Duration of operation be- Duration of operation below • Check configuration tion" fault stop low 5 Hz exceeded 5 Hz exceeded • Shorten duration of opera- tion below 5 Hz Analog input No response...
  • Page 219 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure "Absolute en- Immediate 16385 X14: Plausibility monitor- • Encoder cable or shield not • Check encoder cable and coder option" stop connected correctly shield for correct connec- •...
  • Page 220 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure "Absolute en- Immediate X15: Critical transmitter Soiled, transmitter broken Replace encoder coder option" stop current 16445 X14: Critical transmitter current X15: Critical encoder tem- Encoder temperature too high Reduce motor and ambient perature...
  • Page 221 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure Power sec- Immediate Discharge resistor Discharge resistor overload Observe waiting time for tion stop power on/off Hardware ID precharge/ Incorrect precharge/discharge • Consult SEW Service discharge control controller variant •...
  • Page 222 Service Fault messages and list of faults Fault Subfault Code Designation Response Code Designation Possible cause Measure Supply sys- Immediate Line overvoltage (motor in- Inadequate line voltage quality • Check supply (fuses, con- stop verter only at start of pre- tactor) charging process) •...

  • Page 223: Sew-Eurodrive Electronics Service

    Service SEW‑EURODRIVE electronics service SEW‑EURODRIVE electronics service 7.4.1 Sending a device in for repair Please contact the SEW‑EURODRIVE electronics service if a fault cannot be rec- tified (→ "Customer and spare parts service"). When you contact the SEW‑EURODRIVE electronics service, always quote the digits on the status label so that our service personnel can assist you more effectively.

  • Page 224: Waste Disposal

    Service Waste disposal Waste disposal Please follow the current instructions. Dispose of the following materials in accord- ance with the regulations in force: • Electronics scrap (printed circuit boards) • Plastic (housing) • Sheet metal • Copper ® Operating Instructions – MOVIDRIVE MDX60B/61B...

  • Page 225: Technical Data Of Basic Device

    Technical data of basic device CE marking, approvals Technical data of basic device CE marking, approvals 8.1.1 CE marking • Low Voltage Directive ® MOVIDRIVE   MDX60B/61B drive inverters comply with the regulations of the Low Voltage Directive 2014/35/EU. • Electromagnetic compatibility (EMC) ® MOVIDRIVE drive inverters and regenerative power supply units are designed for use as components for installation in machinery and systems.

  • Page 226: General Technical Data

    Technical data of basic device General technical data General technical data ® The following table lists the technical data applicable to all MOVIDRIVE MDX60/61B drive inverters, regardless of their type, design, size, and power rating. ® MOVIDRIVE MDX60B/61B All sizes Interference immunity Meets EN 61800-3 Interference emission with EMC...
  • Page 227 Technical data of basic device General technical data ® MOVIDRIVE MDX60B/61B All sizes Installation altitude h Up to h ≤ 1000 m without restrictions. The following restrictions apply at h ≥ 1000 m: • From 1,000 m to max. 4,000 m: – reduction by 1% per 100 m •...

  • Page 228: Movidrive® Mdx60/61B

    Technical data of basic device MOVIDRIVE® MDX60/61B...-5_3 (AC 400/500 V units) MOVIDRIVE ® M DX60/61B ...-5_3 (AC 400/50 0 V units) ® MOVIDRIVE MDX60/61B...-5_3 (AC 400/500 V units) ® 8.3.1 MOVIDRIVE MDX60/61B0005/0008/0011/0014 size 0 (AC 400/500 V devices) ® MOVIDRIVE MDX60/61B 0005-5A3-4-0_ 0008-5A3-4-0_ 0011-5A3-4-0_ 0014-5A3-4-0_ Size INPUT Nominal supply voltage (to EN 50160) 3 ×...
  • Page 229 Technical data of basic device MOVIDRIVE® MDX60/61B...-5_3 (AC 400/500 V units) Part number 8277303 8277311 827732X 8277338 8289557 8289565 8289573 8289581 MDX61B technology version (VFC/CFC/SERVO) 0005-5A3-4-0T 0008-5A3-4-0T 0011-5A3-4-0T 0014-5A3-4-0T Design with coated printed circuit boards 0005-5A3-4-0T/L 0008-5A3-4-0T/L 0011-5A3-4-0T/L 0014-5A3-4-0T/L Part number 8277346 8277354 8277362 8277370...
  • Page 230 Technical data of basic device MOVIDRIVE® MDX60/61B...-5_3 (AC 400/500 V units) ® 8.3.2 MOVIDRIVE MDX61B0015/0022/0030/0040 size 1 (AC 400/500 V devices) ® MOVIDRIVE MDX61B 0015-5A3-4-0_ 0022-5A3-4-0_ 0030-5A3-4-0_ 0040-5A3-4-0_ INPUT Nominal supply voltage (to EN 50160) 3 × AC 380 V – 500 V line Line frequency 50 Hz – 60 Hz ±5% line Nominal line current 100%...
  • Page 231 Technical data of basic device MOVIDRIVE® MDX60/61B...-5_3 (AC 400/500 V units) ® 8.3.3 MOVIDRIVE MDX61B0055/0075/0110 size 2S, 2 (AC 400/500 V devices) ® MOVIDRIVE MDX61B 0055-5A3-4-0_ 0075-5A3-4-0_ 0110-5A3-4-0_ Size INPUT Nominal supply voltage (to EN 50160) 3 × AC 380 V – 500 V line Line frequency 50 Hz –...
  • Page 232 Technical data of basic device MOVIDRIVE® MDX60/61B...-5_3 (AC 400/500 V units) ® Recommended motor power → MOVIDRIVE B system manual or catalog, chapter Basic recommenda- tions for motor selection ® Operating Instructions – MOVIDRIVE MDX60B/61B...
  • Page 233 Technical data of basic device MOVIDRIVE® MDX60/61B...-5_3 (AC 400/500 V units) ® 8.3.4 MOVIDRIVE MDX61B0150/0220/0300 size 3 (AC 400/500 V devices) ® MOVIDRIVE MDX61B 0150-503-4-0_ 0220-503-4-0_ 0300-503-4-0_ INPUT Nominal supply voltage (to EN 50160) 3 × AC 380 V – 500 V line Line frequency 50 Hz – 60 Hz ±5% line Nominal line current 100%...
  • Page 234 Technical data of basic device MOVIDRIVE® MDX60/61B...-5_3 (AC 400/500 V units) ® 8.3.5 MOVIDRIVE MDX61B0370/0450 size 4 (AC 400/500 V devices) ® MOVIDRIVE MDX61B 0370-503-4-0_ 0450-503-4-0_ INPUT Nominal supply voltage (to EN 50160) 3 × AC 380 V – 500 V line Line frequency 50 Hz – 60 Hz ±5% line Nominal line current 100%...
  • Page 235 Technical data of basic device MOVIDRIVE® MDX60/61B...-5_3 (AC 400/500 V units) ® 8.3.6 MOVIDRIVE MDX61B0550/0750 size 5 (AC 400/500 V devices) ® MOVIDRIVE MDX61B 0550-503-4-0_ 0750-503-4-0_ INPUT Nominal supply voltage (to EN 50160) 3 × AC 380 V – 500 V line Line frequency 50 Hz – 60 Hz ±5% line Nominal line current 100%...
  • Page 236 Technical data of basic device MOVIDRIVE® MDX60/61B...-5_3 (AC 400/500 V units) ® 8.3.7 MOVIDRIVE MDX61B0900/1100/1320 size 6 (AC 400/500 V devices) ® MOVIDRIVE MDX61B 0900-503-4-0_ 1100-503-4-0_ 1320-503-4-0_ INPUT Nominal supply voltage (to EN 50160) 3 × AC 380 V – 500 V line Line frequency 50 Hz – 60 Hz ±5% line Nominal line current 100%...
  • Page 237 Technical data of basic device MOVIDRIVE® MDX60/61B...-5_3 (AC 400/500 V units) ® 8.3.8 MOVIDRIVE MDX61B1600/2000/2500 size 7 (AC 400/500 V devices) ® MOVIDRIVE MDX61B 1600-503-2-0T/L 2000-503-2-0T/L 2500-503-2-0T/L 1600-503-4-0T/L 2000-503-4-0T/L 2500-503-4-0T/L INPUT Nominal supply voltage (to EN 50160) 3 × AC 380 V – 500 V line Line frequency 50 Hz –...

  • Page 238: Movidrive® Mdx61B

    Technical data of basic device MOVIDRIVE® MDX61B...-2_3 (AC 230 V units) MOVIDRIVE ® M DX61B...- 2_3 (AC 230 V units) ® MOVIDRIVE MDX61B...-2_3 (AC 230 V units) ® 8.4.1 MOVIDRIVE MDX61B0015/0022/0037 size 1 (AC 230 V devices) ® MOVIDRIVE MDX61B 0015-2A3-4-0_ 0022-2A3-4-0_ 0037-2A3-4-0_ INPUT Nominal supply voltage (to EN 50160) 3 ×...
  • Page 239 Technical data of basic device MOVIDRIVE® MDX61B...-2_3 (AC 230 V units) ® 8.4.2 MOVIDRIVE MDX61B0055/0075 size 2 (AC 230 V devices) ® MOVIDRIVE MDX61B 0055-2A3-4-0_ 0075-2A3-4-0_ INPUT Nominal supply voltage (to EN 50160) 3 × AC 200 V - 240 V line Line frequency 50 Hz – 60 Hz ±5% line Nominal supply current I 100%...
  • Page 240 Technical data of basic device MOVIDRIVE® MDX61B...-2_3 (AC 230 V units) ® 8.4.3 MOVIDRIVE MDX61B0110/0150 size 3 (AC 230 V devices) ® MOVIDRIVE MDX61B 0110-203-4-0_ 0150-203-4-0_ INPUT Nominal supply voltage (to EN 50160) 3 × AC 200 V - 240 V line Line frequency 50 Hz – 60 Hz ±5% line Nominal supply current I 100%...
  • Page 241 Technical data of basic device MOVIDRIVE® MDX61B...-2_3 (AC 230 V units) ® 8.4.4 MOVIDRIVE MDX61B0220/0300 size 4 (AC 230 V devices) ® MOVIDRIVE MDX61B 0220-203-4-0_ 0300-203-4-0_ INPUT Nominal supply voltage (to EN 50160) 3 × AC 200 V - 240 V line Line frequency 50 Hz – 60 Hz ±5% line Nominal supply current I 100%...

  • Page 242: Movidrive Mdx60/61B Electronics Data

    Technical data of basic device MOVIDRIVE MDX60/61B electronics data MOVIDRIVE MDX60/61B electronics data ® MOVIDRIVE MDX60/61B electronics data ® MOVIDRIVE MDX60/61B General electronics data Voltage supply REF1: DC +10 V +5%/-0%, I  = DC 3 mA Reference voltages for setpoint potentiometer X11:1 REF2: DC -10 V +0%/-5%, I  = DC 3 mA For setpoint input X11:5 Setpoint input n1...
  • Page 243 Technical data of basic device MOVIDRIVE MDX60/61B electronics data ® MOVIDRIVE MDX60/61B General electronics data DCOM: Reference potential of digital inputs X13:1 – X13:6 and X16:1/X16:2 (DIØØ – DIØ5 and X13:7 DIØ6/DIØ7) One core per terminal: 0.20 – 2.5 mm (AWG 24 – 12) Permitted cable cross section Two cores per terminal: 0.25 – 1 mm (AWG 22 – 17) Tightening torque: 0.6 Nm...

  • Page 244: Movidrive Mdx60B Dimension Drawings

    Technical data of basic device MOVIDRIVE® MDX60B dimension drawings MOVIDRIVE ® MDX60B dimension drawings ® MOVIDRIVE MDX60B dimension drawings ® 8.6.1 MOVIDRIVE MDX60B size 0S The following dimension drawing shows MDX60B size 0S, dimensions in mm (in) 6 (0.24) 249 (9.8) 45 (1.8) 260 (10.2) 9007201195536907...
  • Page 245 Technical data of basic device MOVIDRIVE® MDX60B dimension drawings ® 8.6.2 MOVIDRIVE MDX60B, size 0S with mounted braking resistor The following dimension drawing shows MDX60B size 0S with braking resistor, dimen- sions in mm (in) 6 (0.24) 249 (9.8) 71.5 (2.81) 45 (1.8) 260 (10.2) 9007201195539979...
  • Page 246 Technical data of basic device MOVIDRIVE® MDX60B dimension drawings ® 8.6.3 MOVIDRIVE MDX60B size 0M The following dimension drawing shows MDX60B size 0M, dimensions in mm (in) 6 (0.24) 249 (9.8) 67,5 (2.66) 260 (10.2) 9007201195584907 ® Operating Instructions – MOVIDRIVE MDX60B/61B...
  • Page 247 Technical data of basic device MOVIDRIVE® MDX60B dimension drawings ® 8.6.4 MOVIDRIVE MDX60B size 0M with mounted braking resistor The following dimension drawing shows MDX60B size 0M with braking resistor, di- mensions in mm (in) 6 (0.24) 249 (9.8) 94 (3.7) 67,5 (2.66) 260 (10.2) 9007201195587979...

  • Page 248: Movidrive Mdx61B Dimension Drawings

    Technical data of basic device MOVIDRIVE® MDX61B dimension drawings MOVIDRIVE ® MDX61B dimension drawings ® MOVIDRIVE MDX61B dimension drawings INFORMATION ® With MOVIDRIVE ® For MOVIDRIVE MDX61B size 0, installing a braking resistor does not affect the di- ® mensions. Therefore, MOVIDRIVE MDX61B size 0 dimensions are displayed without an installed braking resistor.
  • Page 249 Technical data of basic device MOVIDRIVE® MDX61B dimension drawings ® 8.7.2 MOVIDRIVE MDX61B size 0M The following dimension drawing shows MDX61B size 0M, dimensions in mm (in) 6 (0.24) 249 (9.8) 95 (3.7) 67,5 (2.66) 260 (10.2) 9007201313669643 ® Operating Instructions – MOVIDRIVE MDX60B/61B...
  • Page 250 Technical data of basic device MOVIDRIVE® MDX61B dimension drawings ® 8.7.3 MOVIDRIVE MDX61B size 1 The following dimension drawing shows MDX61B size 1, dimensions in mm (in) 105 (4.13) 234 (9.21) 85 (3.3) 6 (0.24) 6 (0.24) 167 (6.56) 9007201313674123 ®...
  • Page 251 Technical data of basic device MOVIDRIVE® MDX61B dimension drawings ® 8.7.4 MOVIDRIVE MDX61B size 2S The following dimension drawing shows MDX61B size 2S, dimensions in mm (in) 70 (2.8) 7 (0.28) 227 (8.94) 294,1 (11.6) 105 (4.13) 9007201313689995 ® Operating Instructions – MOVIDRIVE MDX60B/61B...
  • Page 252 Technical data of basic device MOVIDRIVE® MDX61B dimension drawings ® 8.7.5 MOVIDRIVE MDX61B size 2 The following dimension drawing shows MDX61B size 2, dimensions in mm (in) 6,5 (0.26) 218 (8.6) 105 (4.13) 285 (11.24) 130 (5.12) 9007201313694091 ® Operating Instructions – MOVIDRIVE MDX60B/61B...
  • Page 253 Technical data of basic device MOVIDRIVE® MDX61B dimension drawings ® 8.7.6 MOVIDRIVE MDX61B size 3 The following dimension drawing shows MDX61B size 3, dimensions in mm (in) 200 (7.89) 145 (5.71) 308 (12.1) 105 (4.13) 2 (0.08) 7 (0.28) 7 (0.28) 9007201313697675 ®...
  • Page 254 Technical data of basic device MOVIDRIVE® MDX61B dimension drawings ® 8.7.7 MOVIDRIVE MDX61B size 4 The following dimension drawing shows MDX61B size 4, dimensions in mm (in) 307 (12.1) 280 (11.0) 2 (0.08) 140 (5.51) 7 (0.3) 2058960267 ® Operating Instructions – MOVIDRIVE MDX60B/61B...
  • Page 255 Technical data of basic device MOVIDRIVE® MDX61B dimension drawings ® 8.7.8 MOVIDRIVE MDX61B size 5 The following dimension drawing shows MDX61B size 5, dimensions in mm (in) 280 (11.0) 330 (13.0) 140 (5.51) 2 (0.08) 7 (0.3) 2058963851 ® Operating Instructions – MOVIDRIVE MDX60B/61B...
  • Page 256 Technical data of basic device MOVIDRIVE® MDX61B dimension drawings ® 8.7.9 MOVIDRIVE MDX61B size 6 The following dimension drawing shows MDX61B size 6, dimensions in mm (in) 382 (15.0) 2 (0.08) 140 (5.51) 11 (0.43) 9 (0.4) 294 (11.6) 318 (12.5) 2058967435 ®...
  • Page 257 Technical data of basic device MOVIDRIVE® MDX61B dimension drawings ® 8.7.10 MOVIDRIVE MDX61B size 7 The following dimension drawing shows MDX61B size 7, dimensions in mm (in) 575 (22.6) 225 (8.86) Ø10 (0.39) 700 (27.6) 473 (18.62) 9007201336579851 ® Operating Instructions – MOVIDRIVE MDX60B/61B...

  • Page 258: Ipos Plus

    Technical data of basic device IPOSplus® IPOSplus® PLUS® IPOS 8.8.1 Description PLUS® ® IPOS positioning and sequence control is integrated into every MOVIDRIVE PLUS® verter as standard. With IPOS control functions and positioning tasks can be per- formed either simultaneously or independently of one another. PLUS®...
  • Page 259 Technical data of basic device IPOSplus® Max. program length of task 1, task 2 and Total of ca. 3200 program lines task 3 Command processing time per program line Task 1: 1 – 10 commands/ms can be configured Task 2: 2 – 11 commands/ms can be configured Task 3: at least 1 command/ms (typical is 40 commands/ Variables 1024, of which 128 (0 – 127) can be stored to non-volatile...

  • Page 260: Dbg60B Keypad

    Technical data of basic device DBG60B keypad DBG60B keypad 8.9.1 Description ® The basic version of MOVIDRIVE does not have a DBG60B keypad, but can be up- graded to include the keypad as an option. Keypad Language variants Part no. DBG60B-10 DE/EN/FR/IT/ES/PT/NL/FI/SV/DA/TR/RU/PL/CS/ 28229150...
  • Page 261 Technical data of basic device DBG60B keypad Features • Illuminated text display, range of languages • Keypad with 21 keys • Selection between user menu, detailed parameter menu and startup menu in VFC mode (CFC and SERVO startup is not possible with the DBG60B) ®...

  • Page 262: Dbm60B/Dkg60B Housing For Dbg60B

    Technical data of basic device DBM60B/DKG60B housing for DBG60B 8.10 DBM60B/DKG60B housing for DBG60B 8.10.1 Description The DBM60B option can be used to mount the keypad close to the inverter (e.g. in the control cabinet door). The DBM60B option consists of a housing in IP65 degree of pro- tection, and a 5 m DKG60B extension cable.

  • Page 263: Technical Data Of Regenerative Power Supply Unit

    Technical data of regenerative power supply unit MOVIDRIVE® MDR60A/61B regenerative power supply unit Technical data of regenerative power supply unit MOVIDRIVE ® M DR60A/61 B r egenerativ e power supply unit ® MOVIDRIVE MDR60A/61B regenerative power supply unit ® MOVIDRIVE drive inverters operating in regenerative mode (4Q operation) can use ®...
  • Page 264 Technical data of regenerative power supply unit MOVIDRIVE® MDR60A/61B regenerative power supply unit 9.1.3 Features of a regenerative power supply unit compared to an inverter with braking resistors • Energy balance: Regenerative power is fed back into the supply system instead of being converted into waste heat.
  • Page 265 Technical data of regenerative power supply unit MOVIDRIVE® MDR60A/61B regenerative power supply unit ® MOVIDRIVE MDR61B regenerative power supply unit ® MOVIDRIVE MDR61B 1600-503-00/L (size 7) 2500-503-00/L (size 7) Interference immunity Meets EN 61800-3 Interference emission with EMC- Meets EN 61800-3: compliant installation •...
  • Page 266 Technical data of regenerative power supply unit MOVIDRIVE® MDR60A/61B regenerative power supply unit ® 9.1.5 Technical data of MOVIDRIVE MDR60A/61B and MDX62B ® MOVIDRIVE MDR60A0150/0370 size 2 and size 3 ® MOVIDRIVE MDR60A Size 2 Size 3 Standard design 0150-503-00 0370-503-00 Design with coated printed circuit boards 0150-503-00/L...
  • Page 267 Technical data of regenerative power supply unit MOVIDRIVE® MDR60A/61B regenerative power supply unit ® MOVIDRIVE MDR60A0750/1320 size 4 and size 6 ® MOVIDRIVE MDR60A Size 4 Size 6 Standard design 0750-503-00 1320-503-00 Design with coated printed circuit boards 0750-503-00/L – Part number 08265569 08279527...
  • Page 268 Technical data of regenerative power supply unit MOVIDRIVE® MDR60A/61B regenerative power supply unit ® MOVIDRIVE MDR60A Size 4 Size 6 Standard design 0750-503-00 1320-503-00 Design with coated printed circuit boards 0750-503-00/L – Recommended line fuse 175 A 500 A 1) The listed technical data applies to devices with serial no. DCV200xxx. For devices of the previous series with no. DCV185xxx, refer to the provided documentation and the data on the nameplate 2) Note: Do not apply tightening torque directly at terminals L1, L2, L3 and ±UG;...
  • Page 269 Technical data of regenerative power supply unit MOVIDRIVE® MDR60A/61B regenerative power supply unit ® MOVIDRIVE MDR61B1600/2500 size 7 ® MOVIDRIVE MDR61B Size 7 1600-503-00/L 2500-503-00/L Part number 18250955 18250963 INPUT Nominal voltage 3 × AC 380 V – 500 V line (according to EN 50160) Line frequency 50 Hz – 60 Hz ± 5% line Rated connected load 160 kW...
  • Page 270 Technical data of regenerative power supply unit MOVIDRIVE® MDR60A/61B regenerative power supply unit ® MOVIDRIVE MDX62B1600/2000/2500 size 7 ® MOVIDRIVE MDX62B Size 7 2-Q devices (without brake chopper) 1600-503-2-0T/L 2000-503-2-0T/L 2500-503-2-0T/L 4-Q devices (with brake chopper) 1600-503-4-0T/L 2000-503-4-0T/L 2500-503-4-0T/L Part number 18250459 18250467 18250475...
  • Page 271 Technical data of regenerative power supply unit MOVIDRIVE® MDR60A/61B regenerative power supply unit 9.1.6 Dimension drawings ® MOVIDRIVE MDR60A0150 size 2 Observe the following minimum clearance for control cabinet installation: • 100 mm above and below • No clearance required on the side 3349923979 All dimensions in mm (in) ®...
  • Page 272 Technical data of regenerative power supply unit MOVIDRIVE® MDR60A/61B regenerative power supply unit ® MOVIDRIVE MDR60A0370 size 3 Observe the following minimum clearance for control cabinet installation: • 100 mm above and below • No clearance required on the side 7 (0.3) 173 (6.81) 105 (4.13) 200 (7.87)
  • Page 273 Technical data of regenerative power supply unit MOVIDRIVE® MDR60A/61B regenerative power supply unit ® MOVIDRIVE MDR60A0750 size 4 Observe the following minimum clearance for control cabinet installation: • 100 mm above and below • The minimum distance above the inverter for installing temperature-sensitive com- ponents, such as contactors or fuses, is 300 mm •...
  • Page 274 Technical data of regenerative power supply unit MOVIDRIVE® MDR60A/61B regenerative power supply unit ® MOVIDRIVE MDR60A1320 size 6 Observe the following minimum clearance for control cabinet installation: • 100 mm above • Do not install any components that are sensitive to high temperatures within 300 mm above the device, for example contactors or fuses •...
  • Page 275 Technical data of regenerative power supply unit MOVIDRIVE® MDR60A/61B regenerative power supply unit ® MOVIDRIVE MDR61B1600/2500 size 7 Observe the following minimum clearance for control cabinet installation: • 100 mm above • Do not install any components that are sensitive to high temperatures within 300 mm above the device, for example contactors or fuses •...
  • Page 276 Technical data of regenerative power supply unit MOVIDRIVE® MDR60A/61B regenerative power supply unit ® MOVIDRIVE MDX62B1600/2000/2500 size 7 Observe the following minimum clearance for control cabinet installation: • 100 mm above • Do not install any components that are sensitive to high temperatures within 300 mm above the device, for example contactors or fuses •...
  • Page 277 Technical data of regenerative power supply unit MOVIDRIVE® MDR60A/61B regenerative power supply unit 9.1.7 DC link connection SEW‑EURODRIVE recommends using the following cable sets for the DC link con- nection. These cable sets offer the appropriate dielectric strength and are also color- coded.

  • Page 278: Technical Data Of Options

    Technical data of options HIPERFACE® encoder card DEH11B Technical data of options HIPERFAC E® encoder card DEH11B ® 10.1 HIPERFACE encoder card DEH11B 10.1.1 Part number 08243107 10.1.2 Description ® Option-capable MOVIDRIVE MDX61B devices can be equipped with the ® HIPERFACE encoder card type DEH11B.

  • Page 279: Resolver Card Der11B

    Technical data of options Resolver card DER11B 10.2 Resolver card DER11B 10.2.1 Part number 08243077 10.2.2 Description ® Option-capable MOVIDRIVE MDX61B devices can be equipped with resolver card type DER11B. The resolver card offers one input for the resolver as motor encoder and one input for external encoder, also referred to as a distance encoder.

  • Page 280: Deu21B Multi-Encoder Card

    Technical data of options DEU21B multi-encoder card 10.3 DEU21B multi-encoder card 10.3.1 Part number 18221696 10.3.2 Description ® Option-capable MOVIDRIVE MDX61B units can be equipped with a DEU21B multi- encoder card. The encoder card provides one input for the motor encoder and one in- put for an external encoder, also referred to as a distance encoder.

  • Page 281: Deh21B/Dip11B Absolute Encoder Card

    Technical data of options DEH21B/DIP11B absolute encoder card 10.4 DEH21B/DIP11B absolute encoder card 10.4.1 Part numbers • DEH21B: 18208185 • DIP11B: 08249695 10.4.2 Description ® The DEH21B and DIP11B options extend the MOVIDRIVE B system to include an PLUS® SSI interface for absolute encoders. This enables the following options for IPOS positioning: •...
  • Page 282 Technical data of options DEH21B/DIP11B absolute encoder card 10.4.4 Electronics data for DIP11B DIP11B option Digital input connection X60:1 – 8 DI10 – DI17 isolated via optocoupler, PLC-compatible (EN 61131), sampling cycle 1 ms Internal resistance  ≈ 3 kΩ, I  ≈ DC 10 mA Signal level (EN 61131) DC +13 V – +30 V = "1" / DC-3 V – +5 V = "0" Function X60:1 – 8 DI10 – DI17;...

  • Page 283: Connector Adapter For Device Replacement Md_60A - Mdx60B/61B

    Technical data of options Connector adapter for device replacement MD_60A - MDX60B/61B 10.5 Connector adapter for device replacement MD_60A - MDX60B/61B ® The following adapters are available for quick replacement of a MOVIDRIVE A with a ® MOVIDRIVE B during system operation. •...
  • Page 284 Technical data of options Connector adapter for device replacement MD_60A - MDX60B/61B DAE14B 1454702731 • Length of DAE14B: 200 mm ± 20 mm Cable cross section: 6 x 2 x 0.25 mm (AWG 23) ® Operating Instructions – MOVIDRIVE MDX60B/61B...

  • Page 285: Dwe11B/12B Interface Adapter

    Technical data of options DWE11B/12B interface adapter 10.6 DWE11B/12B interface adapter 10.6.1 Part number and description DWE11B, part number 01881876 • The interface adapter DWE11B (HTL→TTL) in the form of an adapter cable is used to connect single-ended HTL encoders to the DEH11B/DEH21B option. Only the A, B and C tracks are connected.

  • Page 286: Uws11A Interface Adapter

    Technical data of options UWS11A interface adapter 10.7 UWS11A interface adapter 10.7.1 Part number 0822689X 10.7.2 Description The UWS11A option converts RS232 signals, for example from the PC, into RS485 signals. These RS485 signals can then be routed to the RS485 interface of the in- verter.
  • Page 287 Technical data of options UWS11A interface adapter Dimension drawing of UWS11A 68 (2.7) 5 (0.2) 22.5 (0.88) 83 (3.3) 1454780939 All dimensions in mm (in) The UWS11A option is mounted on a mounting rail (EN 50022-35 × 7.5) in the control cabinet.

  • Page 288: Uws21B Interface Adapter

    Technical data of options UWS21B interface adapter 10.8 UWS21B interface adapter 10.8.1 Part number 18204562 10.8.2 Description The UWS21B option converts RS232 signals, for example from the PC, into RS485 signals. These RS485 signals can then be routed to the XT slot of the inverter. 10.8.3 RS232 interface The connection between UWS21B and PC is made using a commercially available...
  • Page 289 Technical data of options UWS21B interface adapter Dimension drawing for UWS21B 96 (3.8) 25 (0.98) 90 (3.5) 1454854283 All dimensions in mm (in) ® Operating Instructions – MOVIDRIVE MDX60B/61B...

  • Page 290: Usb11A Interface Adapter

    Technical data of options USB11A interface adapter 10.9 USB11A interface adapter 10.9.1 Part number 08248311 10.9.2 Description Option USB11A enables a PC or laptop with a USB interface to be connected to the XT slot of the inverter. The USB11A interface adapter supports USB 1.1 and USB 2.0. 10.9.3 USB11A –...
  • Page 291 Technical data of options USB11A interface adapter Dimension drawing All dimensions in mm (in) 25 (0.98) 92.5 (3.64) 90 (3.0) 1454863115 ® Operating Instructions – MOVIDRIVE MDX60B/61B...

  • Page 292: Dwi11A Dc 5 V Encoder Supply

    Technical data of options DWI11A DC 5 V encoder supply 10.10 DWI11A DC 5 V encoder supply 10.10.1 Part number 08227594 10.10.2 Description If you are using an incremental encoder with a DC 5 V encoder supply, install the DC 5 V encoder supply option type DWI11A between the inverter and the incremental en- coder.
  • Page 293 Technical data of options DWI11A DC 5 V encoder supply 10.10.5 Technical data DC 5 V encoder supply option type DWI11A Part number 08227594 Voltage input DC 10 – 30 V, I = DC 120 mA Encoder voltage supply DC +5 V (to V ≈ +10 V), I = DC 300 mA Max.

  • Page 294: Dio11B Input/Output Board

    Technical data of options DIO11B input/output board 10.11 DIO11B input/output board 10.11.1 Part number 08243085 10.11.2 Description ® The number of inputs/outputs of the basic MOVIDRIVE B device can be expanded with the DIO11B option. The DIO11B option is plugged into the fieldbus slot. If the fieldbus slot is not available, you can plug the DIO11B option into the expansion slot.
  • Page 295 Technical data of options DIO11B input/output board 10.11.4 Functions • 8 digital inputs • 8 digital outputs • 1 analog differential input (DC 0 – 10 V, DC -10 V – +10 V, DC 0 – 20 mA with cor- responding load) • 2 analog outputs (DC -10 V – +10 V, DC 0 – 20 mA, DC 4 – 20 mA) ®...

  • Page 296: Profibus Dfp21B Fieldbus Interface

    Technical data of options PROFIBUS DFP21B fieldbus interface 10.12 PROFIBUS DFP21B fieldbus interface 10.12.1 Part number 08242402 10.12.2 Description ® MOVIDRIVE B can be equipped with a 12 Mbaud fieldbus interface for the PROFIBUS-DP serial bus system. The device master data (GSD) and type files for ®...

  • Page 297: Interbus Fieldbus Interface Dfi11B

    Technical data of options INTERBUS fieldbus interface DFI11B 10.13 INTERBUS fieldbus interface DFI11B 10.13.1 Part number 08243093 10.13.2 Description ® MOVIDRIVE B can be equipped with a fieldbus interface for the non-proprietary and standardized INTERBUS sensor/actuator bus system. INTERBUS is defined in EN 50254/DIN 19258 and, as far as its function is concerned, it consists of a process data channel and a parameter data channel.

  • Page 298: Interbus Foc Fieldbus Interface Dfi21B

    Technical data of options INTERBUS FOC fieldbus interface DFI21B 10.14 INTERBUS FOC fieldbus interface DFI21B 10.14.1 Part number 08243115 10.14.2 Description ® MOVIDRIVE B can be equipped with a fieldbus interface for the non-proprietary and standardized sensor/actuator bus system INTERBUS/INTERBUS with optical fibers (INTERBUS FOC).

  • Page 299: Fieldbus Interface Profinet Io Rt Dfe32B

    Technical data of options Fieldbus interface PROFINET IO RT DFE32B 10.15 Fieldbus interface PROFINET IO RT DFE32B 10.15.1 Part number 18213456 10.15.2 Description ® The MOVIDRIVE MDX61B drive inverter enables you to use the DFE32B option to connect to higher-level automation, project planning and visualization systems via Eth- ernet (PROFINET IO protocol) thanks to its powerful, universal fieldbus interface.
  • Page 300 Technical data of options Fieldbus interface PROFINET IO RT DFE32B 10.15.4 Functions • PROFINET IO protocol • Two RJ45 plug connectors for star or line type cabling • Up to 10 process data and PROFINET diagnostic parameter data items can be transferred at the same time •...

  • Page 301: Dfe33B Fieldbus Interface For Ethernet/Ip And Modbus Tcp

    Technical data of options DFE33B fieldbus interface for EtherNet/IP™ and Modbus TCP DFE33B fieldbus interface EtherNet/ IP™ and Modbus ™ 10.16 DFE33B fieldbus interface for EtherNet/IP and Modbus TCP 10.16.1 Part number 18213464 10.16.2 Description ® The MOVIDRIVE MDX61B drive inverter enables you to use the DFE33B option to connect to higher-level automation, project planning and visualization systems via Eth- ™...
  • Page 302 Technical data of options DFE33B fieldbus interface for EtherNet/IP™ and Modbus TCP 10.16.4 Functions ™ • EtherNet/IP protocol • Two RJ45 plug connectors for star or line type cabling • Up to 10 process data and parameter data items can be transferred at the same time •...

  • Page 303: Ethercat® Dfe24B Fieldbus Interface

    Technical data of options EtherCat® DFE24B fieldbus interface EtherCat® DFE24B fieldbus interface ® 10.17 EtherCAT DFE24B fieldbus interface 10.17.1 Part number 18211267 10.17.2 Description ® The MOVIDRIVE MDX61B drive inverter enables you to use the DFE24B option to connect to higher-level automation, project planning and visualization systems via ®...

  • Page 304: Devicenet™ Dfd11B Fieldbus Interface

    Technical data of options DeviceNet™ DFD11B fieldbus interface DeviceNet ™ DFD11B fieldbus interface ™ 10.18 DeviceNet DFD11B fieldbus interface 10.18.1 Part number 08249725 10.18.2 Description ® The MOVIDRIVE MDX61B drive inverter enables you to use the DFD11B option to connect to higher-level automation, project planning and visualization systems via the ™...

  • Page 305: Can/Canopen Dfc11B Fieldbus Interface

    Technical data of options CAN/CANopen DFC11B fieldbus interface 10.19 CAN/CANopen DFC11B fieldbus interface 10.19.1 Part number 08243174 10.19.2 Description ® The MOVIDRIVE MDX61B drive inverter in conjunction with the DFC11B option al- lows connection to higher-level automation, project planning and visualization systems via the open and standardized CANopen fieldbus system thanks to the option's high- performance universal fieldbus interface.
  • Page 306 Technical data of options CAN/CANopen DFC11B fieldbus interface 10.19.4 Functions ® • CAN Layer 2 and communication profile MOVILINK or CANopen • Electrical isolation via optocoupler INFORMATION If electrical isolation is not required, the CAN-Bus can be connected directly to the basic device at X12:SC11/SC12 without the DFC11B option.

  • Page 307: Synchronous Operation Card Drs11B

    Technical data of options Synchronous operation card DRS11B 10.20 Synchronous operation card DRS11B 10.20.1 Part number 08246726 10.20.2 Description The DSR11B option allows for a group of motors to be operated in phase-synchro- nous operation in relation to one another, or with an adjustable proportional relation- ship.
  • Page 308 Technical data of options Synchronous operation card DRS11B 10.20.3 Electronics data Option DRS11B Digital inputs X40:1 – X40:6 EINGØ – EING5: isolated (optocoupler) PLC-compatible (EN 61131) Internal resistance  ≈ 3 kΩ, I  ≈ DC 10 mA Sampling cycle 5 ms Signal level DC +13 V – +30 V = "1" = contact closed DC -3 V – +5 V = "0" = contact open Function Fixed assignment with: •...

  • Page 309: Fieldbus Interface Profibus Dp-V1 With Profisafe Dfs11B

    Technical data of options Fieldbus interface PROFIBUS DP-V1 with PROFIsafe DFS11B 10.21 Fieldbus interface PROFIBUS DP-V1 with PROFIsafe DFS11B 10.21.1 Part number 18238408 10.21.2 Description ® MOVIDRIVE B can be equipped with the 12 Mbaud fieldbus interface DFS11B for the serial bus system PROFIBUS DP-V1 with PROFIsafe.
  • Page 310 Technical data of options Fieldbus interface PROFIBUS DP-V1 with PROFIsafe DFS11B 10.21.4 Safety section Safety characteristics Maximum possible safety class • SIL 3 according to EN 61508 • Performance level e according to EN ISO 13849-1 System structure 2 channels with diagnostics (1002D) Operating mode selection "High demand"...

  • Page 311: Fieldbus Interface Profibus Dp-V1 With Profisafe Dfs12B

    Technical data of options Fieldbus interface PROFIBUS DP-V1 with PROFIsafe DFS12B 10.22 Fieldbus interface PROFIBUS DP-V1 with PROFIsafe DFS12B 10.22.1 Part number 28204239 10.22.2 Description ® MOVIDRIVE B can be equipped with the 12 Mbaud fieldbus interface DFS12B for the serial bus system PROFIBUS DP-V1 with PROFIsafe.

  • Page 312: Profinet Io Fieldbus Interface With Profisafe Dfs21B

    Technical data of options PROFINET IO fieldbus interface with PROFIsafe DFS21B 10.23 PROFINET IO fieldbus interface with PROFIsafe DFS21B 10.23.1 Part number 18238637 10.23.2 Description ® The MOVIDRIVE MDX61B drive inverter enables you to use the DFE21B option to connect to higher-level automation, project planning and visualization systems via Eth- ernet (PROFINET IO protocol) thanks to its powerful, universal fieldbus interface.
  • Page 313 Technical data of options PROFINET IO fieldbus interface with PROFIsafe DFS21B 10.23.4 Safety section Safety characteristics Maximum possible safety class • SIL 3 according to EN 61508 • Performance level e according to EN ISO 13849-1 System structure 2 channels with diagnostics (1oo2D) Operating mode selection "High demand"...

  • Page 314: Profinet Io Fieldbus Interface With Profisafe Dfs22B

    Technical data of options PROFINET IO fieldbus interface with PROFIsafe DFS22B 10.24 PROFINET IO fieldbus interface with PROFIsafe DFS22B 10.24.1 Part number 28204247 10.24.2 Description ® The MOVIDRIVE MDX61B drive inverter enables you to use the DFS22B option to connect to higher-level automation, project planning and visualization systems via Eth- ernet (PROFINET IO RT protocol) thanks to its powerful, universal fieldbus interface.

  • Page 315: Movisafe Dcs21B/22B/31B/32B Safety Module

    Technical data of options MOVISAFE® DCS21B/22B/31B/32B safety module MOVISAFE ® D CS21B/22 B/31B/32B safety module ® 10.25 MOVISAFE DCS21B/22B/31B/32B safety module 10.25.1 Part numbers • DCS21B safety module with prefabricated DAE34B cable: 28200993 • DCS21B safety module for replacement (without DAE34B): 28200977 •...
  • Page 316 Technical data of options MOVISAFE® DCS21B/22B/31B/32B safety module 10.25.3 Electronics data Option DCS21B/22B/31B/32B LED alarm/error LED watchdog LED system B LED system A X80: Voltage supply connection X81: Digital input connection X82: Connection of digital outputs DO0, DO1 X83: Connection of digital output DO2 X84: Connection of incremental, sin/cos, HTL, or absolute encoder (encoder 1) X85: Connection of incremental, sin/cos, HTL, or absolute encoder (encoder 2) X86: CAN bus connection (only for DCS21B/22B)

  • Page 317: Movi-Plc Basic Dhp11B Controller

    Technical data of options MOVI-PLC® basic DHP11B controller MOVI-PLC® basic DHP11B controller ® 10.26 MOVI‑PLC  basic DHP11B controller 10.26.1 Part numbers ® The MOVI-PLC   basic controller DHP11B.. is available in 3 versions, which differ in the modules available from a range of libraries. ®...

  • Page 318: Ost11B

    Technical data of options OST11B 10.27 OST11B 10.27.1 Part number 18205445 10.27.2 Description ® Option OST11B provides an additional RS485 interface (COM2) for MOVI‑PLC basic DHP11B in terminal design or as an engineering interface. Only use option OST11B in ® conjunction with the MOVI‑PLC basic controller DHP11B.

  • Page 319: Dhe/Dhf/Dhr21 And Dhe/Dhf/Dhr41B Controller

    Technical data of options DHE/DHF/DHR21 and DHE/DHF/DHR41B controller 10.28 DHE/DHF/DHR21 and DHE/DHF/DHR41B controller Three types of DH.21B/41B controllers are available, which differ in the fieldbus inter- faces: DH.21B/41B design Fieldbus interfaces DHE21B/41B Ethernet TCP/IP, UDP DHF21B/41B Ethernet TCP/IP, UDP, PROFIBUS DP-V1, ™...
  • Page 320 Technical data of options DHE/DHF/DHR21 and DHE/DHF/DHR41B controller CCU standard performance class The "CCU standard" performance class is intended for application modules with single-axis functionality and medium response times. A maximum of 16 axes can be connected to a configurable application controller. The following application modules are available and can be started up using the AxisConfigurator tool.
  • Page 321 Technical data of options DHE/DHF/DHR21 and DHE/DHF/DHR41B controller 10.28.2 DHE21B/41B electronics data DHE21B/41B option Part number DHE21B option: 18236073 DHE41B option: 18211607 Potential levels Option DHE21B/41B has the following potential levels: • Potential control / CAN 1 / COM1 • Potential COM2 •...
  • Page 322 Technical data of options DHE/DHF/DHR21 and DHE/DHF/DHR41B controller 10.28.3 DHF21B/41B electronics data INFORMATION For connections identical with DHE41B, refer to the "DHE41B electronics data" sec- tion. DHF21B/41B option Part number • DHF21B: 18236081 • DHF41B: 18211615 Potential levels Option DHF21B/41B has the following potential levels: •...
  • Page 323 Technical data of options DHE/DHF/DHR21 and DHE/DHF/DHR41B controller 10.28.4 DHR21B/41B electronics data INFORMATION Connections identical with those of the DHE21B/41B and DHF21B/41B options are described chapters "DHE21B/41B option" and "DHF21B/41B option". DHR21B/41B option Part number • DHR21B: 18236103 • DHR41B: 18216323 ®...

  • Page 324: Safety-Related Bst Brake Module

    Technical data of options Safety-related BST brake module 10.29 Safety-related BST brake module 10.29.1 Part numbers The safety-related brake module is available in three variants: Type designation Part number Approved SEW disk brakes BST 0.6S-460V-00 08299714 All brake coils with a brake coil voltage of AC 460 V and a coil power ≤...
  • Page 325 Technical data of options Safety-related BST brake module 10.29.3 Electronics data Brake DBI24 DGND SVI24 S0V24 P/N: 13001337.1111 S/N: 0053481 rd wh Typ : BST 1.2S−230V−00 13 14 15 5 NC 6 1 NC 2 350 . . . 750V DC 24V DC SAFE SAFE...

  • Page 326: Technical Data Of External Accessories

    Technical data of external accessories DMP11B mounting panel Technical data of external accessories 11.1 DMP11B mounting panel 11.1.1 Part number 08183988 11.1.2 Description DMP11B 1454393867 ® ® If a MOVIDRIVE MD_60A size 2 device is to be replaced by MOVIDRIVE MDX61B size 2S, the MDX61B size 2S can be fitted on the existing mounting plate with the DM- P11B mounting panel.

  • Page 327: Dlb11B Touch Guard

    Technical data of external accessories DLB11B touch guard 11.2 DLB11B touch guard 11.2.1 Part number 08231117 (Scope of delivery 12 pieces) 11.2.2 Description 1454399115 Degree of protection IP20 can be achieved for the following devices with DLB11B touch guard: ® •...

  • Page 328: Dlb21B Touch Guard (For Size 7)

    Technical data of external accessories DLB21B touch guard (for size 7) 11.3 DLB21B touch guard (for size 7) 11.3.1 Part number 18226086 11.3.2 Description 2422310283 You can use the DLB21B touch guard to achieve degree of protection IP20 for the fol- lowing devices: ®...

  • Page 329: Dls11B Mounting Base (For Size 7)

    Technical data of external accessories DLS11B mounting base (for size 7) 11.4 DLS11B mounting base (for size 7) 11.4.1 Part number 18226027 11.4.2 Description 2076984331 2422224267 ® The mounting base is designed specifically for installation of MOVIDRIVE B size 7 (MDX61B1600/2000/2500) in the control cabinet.

  • Page 330: Dlh11B Wall Bracket (For Size 7)

    Technical data of external accessories DLH11B wall bracket (for size 7) 11.5 DLH11B wall bracket (for size 7) 11.5.1 Part number 18226108 11.5.2 Description 320 (12.6) 14 (0.55) 320 (12.6) 640 (25.2) 700 (47.56) 9007201676959499 ® wall bracket used attaching MOVIDRIVE size (MDX61B1600/2000/2500) to a wall.

  • Page 331: Dla11B Connection Kit (For Size 7)

    Technical data of external accessories DLA11B connection kit (for size 7) 11.6 DLA11B connection kit (for size 7) 11.6.1 Part number 18223125 11.6.2 Description Connection material for connecting supply system and motor cables with cross sec- tions up to 240 mm to the following devices: ®...

  • Page 332: Dlk11B Air Duct (For Size 7)

    Technical data of external accessories DLK11B air duct (for size 7) 11.7 DLK11B air duct (for size 7) 11.7.1 Part number 18226035 11.7.2 Description ® The following figure shows the air duct for dissipating heat from MOVIDRIVE B size 7 (MDX61B1600/2000/2500): 18014400586472715 The air duct extends the integrated device air duct of size 7 to the control cabinet roof...

  • Page 333: Dlz11B Dc Link Coupling (For Size 7)

    Technical data of external accessories DLZ11B DC link coupling (for size 7) 11.8 DLZ11B DC link coupling (for size 7) 11.8.1 Part number The DLZ11B DC link coupling is available in three different lengths: Type Part number DLZ11B / 100 mm 18231934 DLZ11B / 200 mm 18235662...

  • Page 334: Dlz12B Dc Link Adapter (For Size 7)

    Technical data of external accessories 2Q DLZ12B DC link adapter (for size 7) 11.9 2Q DLZ12B DC link adapter (for size 7) 11.9.1 Part number 18227295 11.9.2 Description 2422222347 DC link adapter for routing the DC link connection to the bottom of the device. For devices: •...
  • Page 335 Technical data of external accessories 2Q DLZ12B DC link adapter (for size 7) • MDX62B2000-503-2-0T/L • MDX62B2500-503-2-0T/L The DC link connection (+U ; -U ) of size 7 can be connected on the side as standard. The 2Q DC link adapter provides a connection option for +U and -U at the bottom of the device.

  • Page 336: Dlz14B Dc Link Adapter (For Size 7)

    Technical data of external accessories 4Q DLZ14B DC link adapter (for size 7) 11.10 4Q DLZ14B DC link adapter (for size 7) 11.10.1 Part number 18227287 11.10.2 Description 2435823499 DC link adapter for routing the DC link connection to the bottom of the device. For devices: •...

  • Page 337: Technical Data Of Braking Resistors, Chokes And Filters

    Technical data of braking resistors, chokes and filters Braking resistors BW.. / BW...-T / BW...-P Technical data of braking resistors, chokes and filters 12.1 Braking resistors BW.. / BW...-T / BW...-P 12.1.1 General information • Braking resistors BW... / BW...-T and BW...-P match the technical features of the ®...
  • Page 338 Technical data of braking resistors, chokes and filters Braking resistors BW.. / BW...-T / BW...-P Wire and grid resistors • Perforated sheet cover (IP20) open to mounting surface • The short-term load capacity of the wire and grid resistors is higher than in the flat- ®...
  • Page 339 Technical data of braking resistors, chokes and filters Braking resistors BW.. / BW...-T / BW...-P 12.1.5 Assignment to AC 400/500 V devices (...-5_3) Braking resistor type BW... BW090- BW100-005 BW100-006 BW072-00 BW072-00 BW168 BW268 P52B Part number 08245630 08262691 08217017 08260583 08260605 0820604X 08207151...
  • Page 340 Technical data of braking resistors, chokes and filters Braking resistors BW.. / BW...-T / BW...-P Braking resistor type BW... BW018-015 Load capacity 50% cdf 2.5 kW 5.9 kW 12.7 kW 27.2 kW At 25% cdf 4.5 kW 10.5 kW 22.5 kW 48 kW 12% cdf 6.7 kW 15.7 kW 33.7 kW 62.7 kW 6% cdf 11.4 kW...
  • Page 341 Technical data of braking resistors, chokes and filters Braking resistors BW.. / BW...-T / BW...-P Braking resistor type BW..-T/-P BW106-T BW206-T BW1.4-170 BW003-420-T Tripping current (of F16) I 47.4 A 54.7 A 110 A 129 A Design Grid resistor Connections / M8 bolts/6 Nm Bolt M12 / 15.5 Nm Tightening torque Degree of protection...
  • Page 342 Technical data of braking resistors, chokes and filters Braking resistors BW.. / BW...-T / BW...-P 12.1.6 Assignment to AC 230 V devices (...-2_3) Braking resistor type BW... BW039-0 BW039-0 BW039-01 BW027-00 BW027-01 Part number 08216878 08216886 0821689 4 8224226 8224234 Braking resistor type BW...-T BW039-012 BW039-026 BW018-015...
  • Page 343 Technical data of braking resistors, chokes and filters Braking resistors BW.. / BW...-T / BW...-P 12.1.7 Technical data of BW...-T / BW...-P braking resistors BW...-T / BW...-P Connection cross section for signal contact/tightening 1 x 2.5 mm / 1 Nm torque Switching capacity of the temperature switch signal •...
  • Page 344 Technical data of braking resistors, chokes and filters Braking resistors BW.. / BW...-T / BW...-P 12.1.8 Dimension drawing of BW.../BW...-T/BW...-P braking resistors The following figure shows the mechanical dimensions in mm (in). BW... : • 1 = Flat design The connection lead is 500 mm long.
  • Page 345 Technical data of braking resistors, chokes and filters Braking resistors BW.. / BW...-T / BW...-P Mounting position 3 BW... type Main dimensions in mm Fastening parts mm Cable gland Mass BW..-T/BW...-P A/A' BW018-015 PG11 BW027-006 PG11 BW027-012 PG11 BW039-003 PG11 BW039-006 PG11 BW039-012...
  • Page 346 Technical data of braking resistors, chokes and filters Braking resistors BW.. / BW...-T / BW...-P 12.1.9 Dimension drawings of BW1.4-170 and BW003-420-T braking resistors The following figure shows the mechanical dimensions in mm. Ø10.5 2649275275 BW... type Main dimensions in mm Mass BW..-T/BW...-P BW1.4-170...
  • Page 347 Technical data of braking resistors, chokes and filters Braking resistors BW.. / BW...-T / BW...-P 12.1.10 BS... touch guard Description A BS.. touch guard is available for braking resistors in flat design. Touch guard BS003 BS005 Part number 08131511 0813152X for braking resistor BW027-003 BW027-005...
  • Page 348 Technical data of braking resistors, chokes and filters Braking resistors BW.. / BW...-T / BW...-P 12.1.11 DKB11A heat sink for braking resistors in flatpack design Part number 08143455 Description The DKB11A heat sink for braking resistors in flatpack design provides a compact means for mounting the braking resistors (BW072-005, BW100 ...
  • Page 349 Technical data of braking resistors, chokes and filters ND.. line chokes 12.2 ND.. line chokes Using line chokes is optional: • To support overvoltage protection • To smoothen the line current, to reduce harmonics • For protection in the event of distorted line voltage •...
  • Page 350 Technical data of braking resistors, chokes and filters ND.. line chokes 12.2.1 Dimension drawing for line chokes ND020.. / ND030.. / ND045.. / ND085.. 1U1 1U2 1V1 1V2 1W1 1W2 1455926923 Space for installation terminals Input: 1U1, 1V1, 1W1 Any mounting position Output: 1U1, 1V2, 1W2 Line choke Main dimensions in mm...
  • Page 351 Technical data of braking resistors, chokes and filters NF...-... line filters 12.3 NF...-... line filters • To suppress interference emission on the line side of inverters. • Do not switch between the NF... line filter and inverter. • NF.. line filters have cRUus approval independent of inverter. Line filter type NF009-503 NF014-503...
  • Page 352 Technical data of braking resistors, chokes and filters NF...-... line filters Line filter type NF300-503 NF600-503 Connections L1-L3/L1'-L3' 150 mm Connection rail with bore for M12 (AWG300-2) Max. 2 × 240 mm Tightening torque L1-L3/L1'-L3' 20 Nm 70 Nm Connection     PE Tightening torque PE 17 Nm 36 Nm Assignment to AC 400/500 V devices (MDX60/61B...-5_3) Nominal operation (100%) 1320/1600 2000/2500...
  • Page 353 Technical data of braking resistors, chokes and filters NF...-... line filters 12.3.1 Dimension drawing of NF009-503 – NF300-503 line filter LINE LOAD 9007200711128075 Any mounting position Line filter Main dimensions in mm Mounting dimensions mm Hole dimension PE connec- Mass type tion NF009-503...
  • Page 354 Technical data of braking resistors, chokes and filters NF...-... line filters 12.3.2 Dimension drawing of NF600-503 line filter 9007201690562571 Any mounting position Line filter type PE connection Mass NF600-503 16.8 ® Operating Instructions – MOVIDRIVE MDX60B/61B...
  • Page 355 Technical data of braking resistors, chokes and filters HD... output chokes 12.4 HD... output chokes • For suppression of interference from the unshielded motor cable. For HD001 to HD003 we recommend routing the motor cable through the output choke with 5 loops.
  • Page 356 Technical data of braking resistors, chokes and filters HD... output chokes 12.4.2 Dimension drawing of HD004 The following figure shows the mechanical dimensions in mm (in): ® MOVIDRIVE HD004 1457368587 Output Main dimensions in mm Mounting dimensions mm Inner diameter Hole dimension Mass choke type...
  • Page 357 Technical data of braking resistors, chokes and filters HD... output chokes 12.4.3 Dimension drawing of HD005 The following figure shows the mechanical dimensions in mm (in). 9007201690562571 Output choke type PE connection Mass HD005 ® Operating Instructions – MOVIDRIVE MDX60B/61B...
  • Page 358 Technical data of braking resistors, chokes and filters HF... output filter 12.5 HF... output filter HF... output filters are sine filters used to smooth output voltage of inverters. HF... out- put filters (with the exception of HF450-503, HF180-403, HF325-403) are approved to UL/cUL in combination inverters.
  • Page 359 Technical data of braking resistors, chokes and filters HF... output filter Output filter type HF075-503 HF023-403 HF033-403 HF047-403 HF450-503 HF180-403 HF325-403 Part number 08263132 08257841 0825785X 08257868 08269483 08299099 08299102 Nominal voltage V 3 × AC 230 V – 500 V, 50/60 Hz Leakage current at V ΔI 0 mA Power loss at I...
  • Page 360 Technical data of braking resistors, chokes and filters HF... output filter 12.5.1 Dimension drawings of HF...-503 output filters The following figures show the mechanical dimensions in mm (in). HF008/015/022/030-503 HF040/055/075-503 MOVIDRIVE ® MOVIDRIVE ® MOVIDRIVE ® / MOVITRAC ® 9007200727565579 Only the mounting position shown in the dimension drawing is permitted.
  • Page 361 Technical data of braking resistors, chokes and filters HF... output filter 12.5.2 Dimension drawings of HF...-403 output filters The following figures show the mechanical dimensions in mm (in). 1472830731 Type Main dimensions in mm Mounting dimensions mm Hole di- Ventilation clearances mension Standard installa- Horizontal mount-...

  • Page 362: Declarations Of Conformity

    Declarations of conformity MOVIDRIVE® Declarations of conformity MOVIDRIVE ® ® 13.1 MOVIDRIVE 13.1.1 Declaration of conformity EU Declaration of Conformity Translation of the original text 900230310/EN SEW-EURODRIVE GmbH & Co. KG Ernst-Blickle-Straße 42, D-76646 Bruchsal declares under sole responsibility that the following products ®...

  • Page 363: Movidrive With Dfs11B/Dfs21B

    Declarations of conformity MOVIDRIVE® with DFS11B/DFS21B MOVIDRIVE ® with DFS11B/ DFS21B ® 13.2 MOVIDRIVE with DFS11B/DFS21B 13.2.1 Declaration of conformity EU Declaration of Conformity Translation of the original text 900010510/EN SEW-EURODRIVE GmbH & Co. KG Ernst-Blickle-Straße 42, D-76646 Bruchsal declares under sole responsibility that the following products ®...

  • Page 364: Movidrive With Dcs2.B/Dcs3.B

    Declarations of conformity MOVIDRIVE® with DCS2.B/DCS3.B MOVIDRIVE ® with DCS2.B/ DCS3.B ® 13.3 MOVIDRIVE with DCS2.B/DCS3.B 13.3.1 Declaration of conformity EU Declaration of Conformity Translation of the original text 901920513/EN SEW-EURODRIVE GmbH & Co. KG Ernst-Blickle-Straße 42, D-76646 Bruchsal declares under sole responsibility that the following products ®...

  • Page 365: Address List

    Fax +213 21 8222-84 Bellevue http://www.reducom-dz.com 16200 El Harrach Alger info@reducom-dz.com Argentina Assembly Buenos Aires SEW EURODRIVE ARGENTINA S.A. Tel. +54 3327 4572-84 Sales Ruta Panamericana Km 37.5, Lote 35 Fax +54 3327 4572-21 (B1619IEA) Centro Industrial Garín http://www.sew-eurodrive.com.ar Prov. de Buenos Aires sewar@sew-eurodrive.com.ar...
  • Page 366 Address list Cameroon Sales Douala SEW-EURODRIVE S.A.R.L. Tel. +237 233 39 02 10 Ancienne Route Bonabéri Fax +237 233 39 02 10 P.O. Box sew@sew-eurodrive-cm B.P 8674 Douala-Cameroun Canada Assembly Toronto SEW-EURODRIVE CO. OF CANADA LTD. Tel. +1 905 791-1553 Sales 210 Walker Drive Fax +1 905 791-2999...
  • Page 367 Address list Colombia Assembly Bogota SEW-EURODRIVE COLOMBIA LTDA. Tel. +57 1 54750-50 Sales Calle 17 No. 132-18 Fax +57 1 54750-44 Service Interior 2 Bodega 6, Manzana B http://www.sew-eurodrive.com.co Santafé de Bogotá sew@sew-eurodrive.com.co Croatia Sales Zagreb KOMPEKS d. o. o. Tel.
  • Page 368 Address list France Lyon SEW-USOCOME Tel. +33 4 74 99 60 00 75 rue Antoine Condorcet Fax +33 4 74 99 60 15 38090 Vaulx-Milieu Nantes SEW-USOCOME Tel. +33 2 40 78 42 00 Parc d’activités de la forêt Fax +33 2 40 78 42 20 4 rue des Fontenelles 44140 Le Bignon Paris...
  • Page 369 Address list Germany Würzburg SEW-EURODRIVE GmbH & Co KG Tel. +49 931 27886-60 Nürnbergerstraße 118 Fax +49 931 27886-66 97076 Würzburg-Lengfeld dc-wuerzburg@sew-eurodrive.de Drive Service Hotline / 24 Hour Service 0 800 SEWHELP 0 800 7394357 Great Britain Assembly Normanton SEW-EURODRIVE Ltd. Tel.
  • Page 370 Address list Indonesia Surabaya PT. TRIAGRI JAYA ABADI Tel. +62 31 5990128 Jl. Sukosemolo No. 63, Galaxi Bumi Permai Fax +62 31 5962666 G6 No. 11 sales@triagri.co.id Surabaya 60111 http://www.triagri.co.id Surabaya CV. Multi Mas Tel. +62 31 5458589 Jl. Raden Saleh 43A Kav. 18 Fax +62 31 5317220 Surabaya 60174 sianhwa@sby.centrin.net.id...
  • Page 371 Address list Lebanon Sales (Lebanon) Beirut Gabriel Acar & Fils sarl Tel. +961 1 510 532 B. P. 80484 Fax +961 1 494 971 Bourj Hammoud, Beirut ssacar@inco.com.lb Sales (Jordan, Kuwait , Beirut Middle East Drives S.A.L. (offshore) Tel. +961 1 494 786 Saudi Arabia, Syria) Sin El Fil.
  • Page 372 Fax +595 21 3285539 Departamento Central sewpy@sew-eurodrive.com.py Fernando de la Mora, Barrio Bernardino Peru Assembly Lima SEW EURODRIVE DEL PERU S.A.C. Tel. +51 1 3495280 Sales Los Calderos, 120-124 Fax +51 1 3493002 Service Urbanizacion Industrial Vulcano, ATE, Lima http://www.sew-eurodrive.com.pe sewperu@sew-eurodrive.com.pe...
  • Page 373 Address list Sambia representation: South Africa Senegal Sales Dakar SENEMECA Tel. +221 338 494 770 Mécanique Générale Fax +221 338 494 771 Km 8, Route de Rufisque http://www.senemeca.com B.P. 3251, Dakar senemeca@senemeca.sn Serbia Sales Belgrade DIPAR d.o.o. Tel. +381 11 347 3244 / +381 11 288 0393 Ustanicka 128a Fax +381 11 347 1337 PC Košum, IV floor...
  • Page 374 Address list South Korea Busan SEW-EURODRIVE KOREA CO., LTD. Tel. +82 51 832-0204 28, Noksansandan 262-ro 50beon-gil, Fax +82 51 832-0230 Gangseo-gu, Busan, Zip 618-820 Spain Assembly Bilbao SEW-EURODRIVE ESPAÑA, S.L. Tel. +34 94 43184-70 Sales Parque Tecnológico, Edificio, 302 http://www.sew-eurodrive.es Service 48170 Zamudio (Vizcaya)
  • Page 375 Address list Ukraine Assembly Dnipropetrovsk ООО «СЕВ-Евродрайв» Tel. +380 56 370 3211 Sales ул. Рабочая, 23-B, офис 409 Fax +380 56 372 2078 Service 49008 Днепр http://www.sew-eurodrive.ua sew@sew-eurodrive.ua Uruguay Assembly Montevideo SEW-EURODRIVE Uruguay, S. A. Tel. +598 2 21181-89 Sales Jose Serrato 3569 Esqina Corumbe Fax +598 2 21181-90 CP 12000 Montevideo...
  • Page 380 SEW-EURODRIVE—Driving the world SEW-EURODRIVE GmbH & Co KG Ernst-Blickle-Str. 42 76646 BRUCHSAL GERMANY Tel. +49 7251 75-0 Fax +49 7251 75-1970 sew@sew-eurodrive.com www.sew-eurodrive.com...

This manual is also suitable for:

Movidrive mdx60b

Table of Contents

Save PDF