Related Manuals for GDS GDS 550P Series
Summary of Contents for GDS GDS 550P Series
- Page 1 Installation and Maintenance Manual Sliding Gate Operators Models: GDS 550P-750P Range Made in Australia from Australian & quality imported components MOVITRAC B A.B.N. 62 059 806 405 April 2010 N14870...
-
Page 2: Abbreviated Installation Instructions
(For those who don't have time!) S l i d i n g G a t e O p e r a t o r s GDS 550, 750 “P” Range Made in Australia from Australian & quality imported components... - Page 3 Press the red commissioning button located next to the inverter and mode switch. (note-there should not be a present input on the open terminal from field wiring, this will prohibit the gate from closing, a momentary pulse is all that is required). Ensure the direction the gate first travels is toward the fully open position, if the gate first travels towards the closed position then turn the power off and reverse two of...
-
Page 4: Table Of Contents
CONTENTS Abbreviated Installation Instructions Page 2-3 Section 1 Safety Precautions Page 4 Section 2 General Information Page 6 Section 3 Wiring Requirements Page 6 Section 4 Installation Page 6-11 Electrical Cabling Mechanical Installation Electrical Connections Connections to Control Board Wiring Diagram Variable Speed Drive Unit Variable Speed Drive Unit –... -
Page 5: Safety Precautions
AFETY RECAUTIONS WARNING! FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS AND INSTALLATION INSTRUCTIONS COULD RESULT IN INJURY OR DEATH AND OR DAMAGE TO PROPERTY AND EQUIPMENT Appropriately licensed and competent personnel only should install the automation equipment. • The operators are designed specifically to open and close sliding gates or doors and should not be used for •... -
Page 6: General Information
GENERAL INFORMATION General Information regarding the “PLC” type operators • These operators incorporate a combined Invertor/PLC in one for the driving and control of the gate. • There is no need for any limit switches, proximity switches or motor encoders as the PLC control system utilises ‘Advanced positioning control’, meaning the PLC always knows where the gate position is as it is driving. -
Page 7: Electrical Connections
Electrical Connections PERATORS 20mm conduit for mains voltage and conduit for low voltage cabling can enter from either side (see cut out • positions on cover) or preferably from the spacing between plate & operator cover. Wire the mains voltage cabling straight to the motor terminals and connect both the shield and earth to the •... -
Page 8: Wiring Diagram
Gate running Output} + 24V 150mA PE (normally closed) Door (not for field connections) OPEN/CLOSE Pedestrian COMMON (for Pedestrian, Open/Close, P.E and Door connections) COMMON (for Pedestrian, Open/Close, P.E and Door connections) EARTH Wiring Diagram for Automation Schematic Wiring Diagram for GDS 550P, 750P Range... - Page 9 Input/Output functions Pedestrian Input: The pedestrian input allows for the gate to be opened to a certain % of the full gate opening distance (20%-80% range). The % can be adjusted via the keypad from the N22 setting (see notes that follow). Open/Initialise Input: This input is used to commission the drive, and also used to open and close the gate.
-
Page 10: Variable Speed Drive Unit
Variable Speed Drive Unit The variable speed drive unit will, ramp up the speed of the operator, run at a predetermined fast speed and • then ramp down prior to closing. For approximately the last 500mm the gate will drive slowly into the stops. The acceleration and deceleration times have been set in the factory for the normal installation but can be •... -
Page 11: Function Factory Settings
Function Factory Settings Acceleration ramp time 5 sec • Deceleration ramp time 4 sec • Maximum speed 4000 rpm (For 750's = 640mm/sec, for 550's = 490mm/sec) • Opening Speed 3640 rpm (For 750's = 580mm/sec, for 550's = 440mm/sec) •... -
Page 12: Commissioning
Commissioning Tighten knurled knob at back of slider, very firmly, by hand so gate will drive. • Power up board and with gate in the half way position, press transmitter or manual control switch • (manufacturer has provided a push button for open/closing/commissioning next to PLC inverter) so operator drives gate. -
Page 13: Fault Finding
6. F AULT INDI NG In the event that the operator does not function due to a fault or unmet condition, there is a simple and effective way of ascertaining where the probable fault may lie. As the invertor is a combination PLC that provides the logic for executing the running of the gate motor, the inputs and their status are very important. -
Page 14: Maintenance
7. M AI NTENANCE ETAI LS WARNING! Failure to maintain equipment may result in injury or death and/or damage to property and equipment Recommended maintenance to be performed on the operator and gate are as follows:- Operator performs over 150 cycles a day each month Operator performs between 100-150 cycles a day every 2 month... -
Page 15: Warranty
8. W ARRANTY Gate Drive Systems Australia warrants that the goods manufactured by it shall be free from defect in manufacture for a period of 12 months from the date of invoice. Should any fault occur within that period as a result of faulty workmanship or materials, Gate Drive Systems Australia will make all necessary repairs, or at its discretion replace the product at no charge to the Customer except for freight.