Assembly; Installing Handwheels; Checking Table Insert - Craftsman 113.298141 Owner's Manual

ItemPart Name Qty.
Z Hex
N ut, 5/16-18
(approx. dia. of hole 5/16 in.) ........... 9
Z Hex Nut, 1t4-20
(approx.dia. of hole 114in.) ............ 2
AA Lockwasher, 5/I 6 in. ExternalType
(approx.die. of hole 5116in.) ........... 11
AA Lockwasher, 1 /4 in. ExternalType
(approx.alia.of h ale 1/4 in.) ............ 2
AA Lockwasher No. 10 ExternalType
(approx.dia. of hole3t16 in.) ........... 1
AB CarriageBolt, 5/16-18 x 3/4 in. long ....... 4
AC Rip FenceGuideBarSpacer .............. 2
AD Wire Tie .............................. 2
AE Thumbscrew, 5 /1G-18 x 1 in. long .......... 1
AF Screw PanHd. 10-32 x 3/4 .............. 1
AG Flat Washer (dia. of hole 21/64) ........... 2
The followingpartsare includedwith Model 113.298031 and
113.298151.
A Leg ................................... 4
8 SideStiffener ........................... 2
C End Stiffener ............................ 2
D Table Extension(113.298031) .............. 2
Table Extension(113.298151) .............. I
E Motor ................................. I
Pkg.of Miscellaneous _ mall Parts,No. 62752for Legs
Consistingof the Following:
F Hex HeadScrew5116-18 x 1-1/4 in. long .... 4,
G Lockwasher, 1/4 in. ExternalType
(approx.dia.of hole1/4 in.) .............. 24
G Lockwasher, 5/16 in. ExternalType
(epprox. dia. of hole 5/16 in.) ............ 4
H Hex Nut, 1/4-20
(approx.dia. of hole 1/4 in.) ............. 24
H Hex Nut, 5/16-18
(approx.dia. of hole5/16 in.) ............. 4
H Hex Nut, 1/2-13
(approx.dia. of hole1]2 in.) ............. 8
J FlatWasher(dia. of hole, 11/32 in.) .......... 8
A
F
J K L
©
G H
Item
K
L
Pert Name Qty.
TrussHeadScrew, 1/4-20 x 5/8 in. long
(top of screwisrounded) ................ 24
Leveling Foot ......................... 4
Pkg.of Miscellaneous S mall PartsNo. 62745 for
Table Extensions (1 ea. for Model 113.298151,
2 ea. for Model 113.298031)
Consistingof the following:
F Hex Hd, Screw,5/16-18 x I-1/4 in. long ..... 4
G Lockwasher, E xternalType
(approx. dia. of hole 1/4 in.) .............. 8
G Lockwasher, ExternalType
(approx.dia. of hale 5/16 in.) ............. 4
H Hex Nut, 1/4-20
(approx.alia.of hole114in.) .............. 8
H Hex Nut, 5/16-18
(approx.dia. of hole5/16 in.) .............. 8
K TrussHeadScrew, 1/4-20 x 1 in. long
(top of screwisrounded) ................ 8
M Corner _;tiffener Bracket .................. 2
N CornerSupportBracket .................. 2
ASSEMBLY
Before mounting the saw on legs, a stand or a bench, the
Table Insert and Blade Squareness must be checked at this
time.
INSTALLING HANDWHEELS
1. Line up FLAT SPOTS on shaft and hardwheel, push
handwheel onto shaft. Install screw and Iockwasher to
lock handwheel on shaft.
ELEVATION
HANDWHEEL
LOCKWASHER
/
10-32 X 3/4 IN.
PAN HEAD SCREW
/
TILT HANDWHEEL
CHECKING TABLE INSERT
2.
Insert should be flush with table top. Check as shown.
Loosen flat head screw that holds insert and adjust the
four set screws as necessary. Tighten flat head screw.
Do not tighten screw to the point where it deflects the
insert.
3/32 I N.
SETSCREWWRENCH
\
TABLE INSERT