Victaulic PC3110 Operating And Maintenance Instruction Manual

Victaulic PC3110 Operating And Maintenance Instruction Manual

Cut and mark tool

Advertisement

Quick Links

OPERATING AND MAINTENANCE INSTRUCTIONS MANUAL
PC3110 Cut and Mark Tool
WARNING
If you need additional copies of any literature, or if you have questions concerning the safe
and proper operation of this tool, contact Victaulic, P.O. Box 31, Easton, PA 18044-0031,
Phone: 1-800-PICK-VIC, E-Mail: pickvic@victaulic.com.
REV_B
WARNING
Failure to follow instructions and warnings could result in death,
serious personal injury, property damage, and/or product damage.
• Before operating or servicing any pipe preparation tools, read all
instructions in this manual and all warning labels on the tool.
• Wear safety glasses, hardhat, foot protection, and hearing
protection while working around this tool.
• Save this operating and maintenance manual in a place
accessible to all operators of the tool.
Original Instructions
TM-PC3110

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PC3110 and is the answer not in the manual?

Questions and answers

Summary of Contents for Victaulic PC3110

  • Page 1 If you need additional copies of any literature, or if you have questions concerning the safe and proper operation of this tool, contact Victaulic, P.O. Box 31, Easton, PA 18044-0031, Phone: 1-800-PICK-VIC, E-Mail: pickvic@victaulic.com.
  • Page 3: Table Of Contents

    TM-PC3110 / Operating and Maintenance Instructions Manual TABLE OF CONTENTS Hazard Identification ....4 Operator Safety Instructions ... . 4 Introduction .
  • Page 4: Hazard Identification

    INSTRUCTIONS Definitions for identifying the various hazard levels are provided below . The PC3110 Cut and Mark Tool is designed to be used, in conjunction with a power drive, for This safety alert symbol indicates the sole purpose of preparing plain-end pipe important safety messages .
  • Page 5 TM-PC3110 / Operating and Maintenance Instructions Manual Ground the power drive to protect the CAUTION operator from electric shock. Verify that the power drive is connected to an internally grounded electrical source . The PC3110 tool is designed ONLY for...
  • Page 6: Introduction

    Victaulic Company. The Victaulic PC3110 Cut and Mark Tool is a portable tool used in conjunction with a power drive for preparing plain-end pipe to be joined Qty.
  • Page 7: Power Requirements

    TM-PC3110 / Operating and Maintenance Instructions Manual POWER REQUIREMENTS EXTENSION CORD REQUIREMENTS When pre-wired outlets are not available and DANGER an extension cord must be used, it is important to use the proper cord size (i .e . Conductor Size •...
  • Page 8: Tool Nomenclature

    TM-PC3110 / Operating and Maintenance Instructions Manual TOOL NOMENCLATURE NOTICE • Drawings and/or pictures in this manual may be exaggerated for clarity. • The tool, along with this operating and maintenance instructions manual, contains trademarks, copyrights, and/or patented features that are the exclusive property of Victaulic.
  • Page 9: Tool Dimensions And Specifications

    TM-PC3110 / Operating and Maintenance Instructions Manual TOOL DIMENSIONS AND SPECIFICATIONS 7.1 in 180 mm 4.4 in 113 mm 17.0 in 432 mm 4.6 in 117 mm Tool weight is 10 .3 pounds/4 .7 kilograms . Tool weight includes the tool head assembly only .
  • Page 10: Pipe Setup

    TM-PC3110 / Operating and Maintenance Instructions Manual PIPE SETUP For proper tool operation and production of pipe ends that are within Victaulic specifications, the following guidelines must be followed . 1. Victaulic requires square-cut pipe for use with plain-end pipe products .
  • Page 11: Tool Setup

    TM-PC3110 / Operating and Maintenance Instructions Manual TOOL SETUP WARNING WARNING • The power drive must be operated with a safety foot switch. Operating the tool without a safety foot switch could result in serious personal injury. 3. Turn the switch on the side of the power drive to FWD (forward) .
  • Page 12: Cutting Operation

    TM-PC3110 / Operating and Maintenance Instructions Manual CUTTING OPERATION DANGER • To reduce the risk of electric shock, check the electrical source for proper grounding. • Before operating the tool, review the “Operator Safety Instructions” section of this manual. Failure to follow these instructions could result in death or serious personal injury.
  • Page 13 TM-PC3110 / Operating and Maintenance Instructions Manual 2. Ensure that the two knurled rolls are centered 4. Using the handle, lift the cutter back to its on the pipe . storage position . 3. Depress the safety foot switch to start the 5.
  • Page 14: Storage Operation

    . PARTS ORDERING INFORMATION When ordering parts, the following information is required for Victaulic to process the order and send the correct part(s) . Parts can be ordered by calling 1-800-PICK-VIC . Tool Model Number...
  • Page 15: Accessories

    TM-PC3110 / Operating and Maintenance Instructions Manual ACCESSORIES CUTTING WHEEL KIT KNURLED ROLLS KIT Item Part No. Qty. Description C Clip R000311CWL Cutting Wheel Item Cutting Wheel Shaft Part No. Qty. Description C Clip CUTTING WHEELS Bushing Knurled Roll with Line...
  • Page 16: Troubleshooting

    Knurling on rolls is filled with debris. Clean knurling surface with a wire brush. defined. Knurled rolls are worn. Replace knurled rolls. In the event of tool malfunction outside the scope of the troubleshooting section, contact Victaulic for assistance. REV_B...
  • Page 17: Knurling/Marking Specifications

    TM-PC3110 / Operating and Maintenance Instructions Manual REV_B...
  • Page 18: Ec Declaration Of Incorporation

    Signed for and on behalf of Victaulic Company, Mr. Len R. Swantek Director – Global Regulatory Compliance Machinery Manufacturer Representative Place of Issue: Easton, Pennsylvania, USA Date of Issue: April 24, 2018 MD_DoI_RGT_009_042418_en.docx VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. ©2013 VICTAULIC COMPANY. ALL RIGHTS RESERVED...
  • Page 19 TM-PC3110 / Operating and Maintenance Instructions Manual This page intentionally blank REV_B...
  • Page 20 OPERATING AND MAINTENANCE INSTRUCTIONS MANUAL PC3110 Cut and Mark Tool UPDATED 04/2018 TM-PC3110 11646 REV B RM00PC3110 VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY AND/OR ITS AFFILIATED ENTITIES IN THE UNITED STATES AND/OR OTHER COUNTRIES. © 2018 VICTAULIC COMPANY. ALL RIGHTS RESERVED.

Table of Contents