Table of Contents
Advertisement
Adam Equipment
CBK & CBK-M SERIES
Adam Equipment strives to be more environmentally focused and uses recycled materials and
environmentally friendly packaging where possible. As part of this initiative we have developed a short form
manual that uses less paper and ink to describe the main functions of your new Adam scale. A complete
version is available at www.adamequipment.com. Thank you for your support of Adam Equipment and we
hope that you enjoy your new scale.
© Adam Equipment Company 2017
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Adam Equipment CBK series
Summary of Contents for Adam Equipment CBK series
- Page 1 Adam scale. A complete version is available at www.adamequipment.com. Thank you for your support of Adam Equipment and we hope that you enjoy your new scale.
- Page 2 © Adam Equipment Company 2017...
-
Page 3: Table Of Contents
RS-232 INTERFACE ....................7 PARAMETERS ......................8 CHECK WEIGHING PARAMETERS..............8 SCALE PARAMETERS ..................9 CALIBRATION ......................10 CBK CALIBRATION .................... 10 BATTERY ....................... 10 SPECIFICATIONS ....................11 ERROR CODES ..................... 14 SERVICE INFORMATION ..................15 © Adam Equipment Company 2017... -
Page 4: Operation
[Zero] key was pressed last. Press [Tare] or [Zero] to remove the tare value and display zero. The Net indicator will disappear. © Adam Equipment Company 2017... -
Page 5: Weighing
NOTE: If the parts are too light to measure accurately, the count may become faulty. It is suggested that the samples to be weighed should each weigh more than the resolution of the scale. © Adam Equipment Company 2017... -
Page 6: Check Counting
The indicator will continue to work with the current settings as active. “rECALL” If you wish to recall any of the pre-stored limits, press [Tare] when © Adam Equipment Company 2017... -
Page 7: Percent Weighing
100.00%. However a small change of weight will cause the display to jump to 102.13% as an increase of one scale division (0.5g) to 24.0g will be equivalent to an increase of 2.13%. © Adam Equipment Company 2017... -
Page 8: Accumulated Totals
While the weight is on the platform, press the [Print] key to view the values- first the accumulation number "ACC x" and then the total will be shown. NOTE: The scale must return to zero or a negative number, before another sample can be added to the memory. © Adam Equipment Company 2017... -
Page 9: Rs-232 Interface
RS-232 interface, outputs the weight with the selected weighing unit. Specifications: RS-232 output of weighing data ASCII code 9600Baud rate(user selectable) 8 data bits No Parity Connector: 9 pin d-subminiature socket Pin 3 Output Pin 2 Input Pin 5 Signal Ground © Adam Equipment Company 2017... -
Page 10: Parameters
The Check weighing password is separate from the scale password, If the password is other than “F2 LLk”, “F3 LEd”, “F4 bEP”, “F5 CPS” 0000, user must enter the password to gain access to and “F6 nCK”. © Adam Equipment Company 2017... -
Page 11: Scale Parameters
Must entered twice when asked. When complete, it will display “donE”. S8 CAL Calibration Calibrate scale. Section 10.0 “S4 dt” NOTE: The parameter is not applicable for CBK-M Scales for use in approved applications. © Adam Equipment Company 2017... -
Page 12: Calibration
10 hours after which it will automatically switch off to protect the battery. 3) To charge the battery, simply plug into the mains power supply. The scale does not need to be turned 4) The battery should be charged for 12 hours for full capacity. © Adam Equipment Company 2017... -
Page 13: Specifications
8000 g 16000 g 32000 g 48000 g Readability 0.1 g 0.1 g 0.2 g 0.5 g Repeatability (S.D.) 0.1 g 0.1 g 0.2 g 0.5 g Linearity (±) 0.2 g 0.2 g 0.4 g © Adam Equipment Company 2017... - Page 14 OTHER SPECIFICATIONS CBK Series- kg, g Units of measure CBKa Series- kg, g, lb, oz, lb:oz Interface RS-232 bi-directional Interface Stabilisation Time 2 Seconds typical -10°C to 40°C Operating Temperature 14°F to 104°F 230 VAC 50/60 Hz Power supply 115 VAC available...
- Page 15 Weighing, Parts counting, % weighing, Check weighing, Functions Check counting, Accumulation of weights Real Time Clock (RTC), To print date and time information- battery backed Date/Time NOTE: For use in approved applications the scales do not come with the RS-232 interface. © Adam Equipment Company 2017...
-
Page 16: Error Codes
The old calibration data FAIL L will be retained until the calibration process is complete. “Err 1” Err 2” FAIL H or FAIL L NOTE: The are not applicable for CBK-M Scales for use in approved applications. © Adam Equipment Company 2017... -
Page 17: Service Information
Include any recent history of the unit. For example: -Has it been working since it’s delivered -Has it been in contact with water -Damaged from a fire -Electrical Storms in the area -Dropped on the floor, etc. © Adam Equipment Company 2017... - Page 18 WARRANTY INFORMATION Adam Equipment offers Limited Warranty (Parts and Labour) for any components that fail due to defects in materials or workmanship. Warranty starts from the date of delivery. During the warranty period, should any repairs be necessary, the purchaser must inform its supplier or Adam Equipment Company.
- Page 19 WARNING: This product includes a sealed lead-acid battery which contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Adam Equipment products have been tested with, and are always supplied with mains power adaptors which meet all legal requirements for the intended country or region of operation, including electrical safety, interference and energy efficiency.
- Page 20 No part of this publication may be reprinted or translated in any form or by any means without the prior permission of Adam Equipment. Adam Equipment reserves the right to make changes to the technology, features, specifications and design of the equipment without notice.
Need help?
Do you have a question about the CBK series and is the answer not in the manual?
Questions and answers