Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Yetter 6010 Planter Unit
Summary of Contents for Yetter 6010 Planter Unit
- Page 1 6010 PLANTER UNIT OPERATOR’S MANUAL & PARTS IDENTIFICATION 2565-724_REV_C ● 10/2018 YETTER MANUFACTURING CO. FOUNDED 1930 Colchester, IL 62326-0358 Toll free: 800/447-5777 309/776-3222 (Fax) Website: www.yetterco.com E-mail: info@yetterco.com...
-
Page 2: Forward/Warranty
WARRANTY Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This warranty being expressly limited to replacement at the factory of such parts or products as shall appear to be defective after inspection. -
Page 3: Safety Information
SAFETY PRECAUTIONS You can make your farm a safer place to live and work if you observe the safety precautions given. Study these precautions carefully and insist those working with you and for you follow the precautions. Finally, remember this an accident is usually caused by someone’s carelessness, neglect or oversight. A brief description of signal words that may be used in this manual: CAUTION: Used as a general reminder of good safety practices or to direct attention to unsafe practices. -
Page 4: Table Of Contents
TABLE OF CONTENTS PAGE FORWARD/WARRANTY……………………………………………………….2 SAFETY INFORMATION……….………………………………………..……..3 TABLE OF CONTENTS……..….………………………………………..……..4 GENERAL INFORMATION/BOLT TORQUE…………………………..……..5 HITCH ASSEMBLY INSTRUCTIONS/PARTS IDENTIFICATION…….…6-7 PLANTING UNIT ASSEMBLY INSTRUCTIONS……………………………………………………………….8-13 SMV EMBLEM INSTALLATION………………………………………………14 LIGHT KIT INSTALLATION…………….……………………………………..15 OPERATING THE PLANTER……………………….……………………..16-22 PARKING STAND INSTALLATION……………….………………………….18 PREDELIVERY LUBRICATION……………………………………………23-24 STORAGE………………………………………………………………………..25 PARTS IDENTIFICATION…………………………..………………………26-34 TROUBLESHOOTING………………………………………………………….35... -
Page 5: General Information/Bolt Torque
GENERAL INFORMATION To achieve maximum performance, this machine must be assembled as outlined in this instruction manual. The planter operator’s manual will NOT include attachment assembly information. Please keep a copy of this instruction available for future attachment assembly. Information in this instruction manual is divided into sections. These sections are identified at the top of each page. Read all assembly instructions and carefully observe illustrations. - Page 6 ASSEMBLY INSTRUCTIONS Step 1. Place the toolbar on two assembly stands approximately 28 inches above the floor or ground. FRONT VIEW OF HITCH ASSEMBLY Step 2. Bolt the center mast brackets (A) together using the 1” x 4-1/2” bolt, upper hitch pipe, lock washer and hex nut (B).
-
Page 7: Hitch Assembly Instructions/Parts Identification
PARTS IDENTIFICATION 6010-010 – CAT I HITCH KIT... -
Page 8: Planting Unit Assembly
PLANTING UNIT ASSEMBLY HOPPER BOTTOM-CORN, SOYBEANS, ACID DELINTED COTTON REGULAR-RATE SORGHUM. 1. Install cutoff (A) in hopper bottom. NOTE: Be sure cutoff is bottomed in hopper bottom ring as shown above. 2. Install seed plate (A) and drive plate (B). 3. -
Page 9: Planting Unit Assembly
PLANTING UNIT ASSEMBLY 7. When planting corn, soybeans, or acid- delinted cotton with the fiber glass hopper, remove cap screws (A) from hopper bottom. 8. Insert ¼ x 3-1/4” bolts (A) through hopper bottom (thread end inside of hopper). 9. Install baffle plate (A) on bolts and secure with springs, flat washers and lock nuts (B). -
Page 10: Planting Unit Assembly
PLANTING UNIT ASSEMBLY HOPPER BOTTOM-BEETS, LOW-RATE SORGHUM OR CUCUMBER 1. Install cutoff (A) in hopper bottom. NOTE: Be certain cutoff is bottomed in hopper bottom ring. 2. Install seed plate (A) and drive plate (B). 3. Install false ring (A). 4. -
Page 11: Planting Unit Assembly
PLANTING UNIT ASSEMBLY HOPPER BOTTOM-PEANUTS OR EDIBLE BEANS 1. Install peanut cutoff (A) and floor plate (B) on hopper bottom and secure with hinge pin (C) and cotter pin. 2. Install recommended peanut seed plate on peanut cutoff with center locator and bolt. - Page 12 PLANTING UNIT ASSEMBLY HOPPER BOTTOM-SOYBEANS AND COTTON SEED (ACID, FLAME, ZIP OR MECHANICALLY DELINTED) NOTE: Stirring rod (A) must be removed when planting soybeans or acid delinted cotton to prevent hard driving. 1. Install cutoff (A) and floor plate (B) on hopper bottom and secure with hinge pin (C) and cotter pin.
-
Page 13: Planting Unit Assembly
PLANTING UNIT ASSEMBLY 1. Install lid and hopper on planting units. Pull latch past locating lug and rotate forward when installing hopper. Secure hopper with latch. -
Page 14: Smv Emblem Installation
SMV EMBLEM INSTALLATION... -
Page 15: Light Kit Installation
OPTIONAL LIGHT KIT INSTALLATION 3400-175... -
Page 16: Operating The Planter
OPERATING THE PLANTER NOTE: Be sure seed tube (A) is installed in clip (B) as shown at right. Double-Disk Seed Opener... - Page 17 OPERATING THE PLANTER DRILLING DISTANCES Four sprockets are shipped with each unit; 11-, 14-, 20- and 22-tooth sprockets. These sprockets will give the seed spacing shown on the following page. The 14-tooth sprocket (A) and 20-tooth sprocket (B) are shipped in place. If other sprocket combinations are desired, remove cap screw (C) and remove sprockets from storage position.
-
Page 18: Parking Stand Installation
ATTACHMENT ASSEMBLY INSTRUCTIONS PARKING STAND ASSEMBLY... - Page 19 OPERATING THE PLANTER LEVELING Drive tractor and planter on level ground. Adjust planter frame to 16 inches (405 mm) above ground. CHANGING PLANTING DEPTH The press wheel gauges the planting depth. The adjustment is from surface plating to 3-1/2 in. (90 mm) deep. To adjust depth, pull out adjustment stop (A) and turn depth control cam (B) to position desired.
- Page 20 OPERATING THE PLANTER Two holes (B) and (C) in the main chain housing (A) permit finer adjustment. increase the planting depth slightly with the adjustment stop pin in hole (B) proceed as follows: Insert the adjustment stop pin into hole (D) and turn to the left until it locks the depth control cam in position in hole (C) in the chain housing.
- Page 21 OPERATING THE PLANTER CENTERING PRESS WHEEL If press wheel (A) does not track directly behind seed opener (B), loosen round head bolts (C) behind drive chain housing. Align press wheel so drive chain housing is at right angle to the toolbar. Tighten round head bolts.
- Page 22 OPERATING THE PLANTER PLANT POPULATION APPROXIMATE PLANT POPULATION PER ACRE CHECKING PLANT POPULATION...
-
Page 23: Predelivery Lubrication
PREDELIVERY LUBRICATION PREDELIVERY LUBRICATION Note that lubrication intervals are identical to those appearing in the operator’s manual. Regardless of recommended intervals, lubricate the planter before delivery at every point shown in the charts with multi-purpose lubricant or an equivalent SAE multi-purpose type grease. - Page 24 LUBRICATION ROLLER CHAIN LUBRICATION The most effective roller chain lubrication routine varies, depending on the environmental conditions and/or conditions of the chain. The obvious goal is to maintain complete freedom at every chain link joint. For best results, DO NOT lubricate roller chains if operating in dusty conditions. Lubrication will only tend to pull additional grit into the critical pivot areas, restring free chain movement.
-
Page 25: Storage
STORAGE BEGINNING OF THE SEASON SERVICE Before using the planter after it has been stored, inspect the seed hoppers for cleanliness to be certain the seed will flow from hoppers freely. Thoroughly inspect the planter unit for loose parts and adjust as necessary. Clean any dirt or grease that may have accumulated on moving parts, gears and chains before operating the planter. -
Page 26: Parts Identification
PARTS IDENTIFICATION SEED HOPPER ASSEMBLY QTY. PART NO. DESCRIPTION 6010-300 LID, HOPPER 6010-301 SEED HOPPER, 71 ROW UNIT 6010-414 1/8 X ½ RIVET 6010-369 SPRING 6010-393 PLATE 2502-105 ¼-20 X ¾ HHCS GR 5 ZYD 2520-151 ¼-20 HEX NUT ZYD 2502-200 5/16-18 X ¾... - Page 27 PARTS IDENTIFICATION PARALLEL ARMS AND TOOLBAR SUPPORTS QTY. PART NO. DESCRIPTION 6010-398 BUSHING 2502-294 ½-13 X 1-1/2 HHCS GR 5 ZYD. 2525-352 ½ MED LOCK WASHER ZYD. 2520-352 ½-13 HEX NUT ZYD. 2526-352 ½ SAE FLAT WASHER ZYD. 2502-294 ½-13 X 1-1/2 HHCS GR 5 ZYD. 2520-357 ½-13 HEX LOCK NUT ZYD.
- Page 28 PARTS IDENTIFICATION HOPPER DRIVE CASE ASSEMBLY AND DEPTH ADJUSTMENT CAM KEY QTY. PART NO. DESCRIPTION KEY QTY. PART NO. DESCRIPTION 6010-311 7/16” JAM NUT ZYD. 2526-352 ½ SAE FLAT WASHER ZYD. 6010-387 SHIELD 2502-281 7/16-14 X ¾ HFLHCS GR5 ZYD 6010-373 BRACE 2525-301...
- Page 29 PARTS IDENTIFICATION BAFFLE AND ACID DELINTED COTTON, BEANS, REGULAR RATE MAIZE AND CORN QTY. PART NO. DESCRIPTION 6010-406 ¼-20 HEX LOCK NUT ZYD 2526-151 ¼ STANDARD FLAT WASHER ZYD 6010-413 COMPRESSION SPRING 6010-389 PLATE 6010-316 ¼-20 X 3-1/4 HHCS GR 2 ZYD...
- Page 30 PARTS IDENTIFICATION SPRING, PLUG AND ANCHOR QTY. PART NO. DESCRIPTION 2502-372 ½-13 X 6-1/2” HHCS GR 5 ZYD. 2525-352 ½ MED LOCK WASHER ZYD. 2520-352 ½-13 HEX NUT ZYD. 6010-396 ½ HRND FLAT WASHER 6010-398 BUSHING 6010-313 7/16-14 X 3 HHCS GR 5 ZYD. 6010-355 ANCHOR 2520-303...
- Page 31 PARTS IDENTIFICATION SEED BOOT, DISK AND BEARING ASSEMBLY QTY. PART NO. DESCRIPTION 6010-395 DISK, 12” X .079” 6010-408 CASE 6010-346 BALL BEARING 6010-404 SCREW, 5/8 X 1, R.H. 6010-405 SCREW, 5/8 X 1, L.H. 6010-344 CASE, R.H. 6010-345 CASE, L.H. 6010-312 ¼...
- Page 32 PARTS IDENTIFICATION SEED BOOT AND DRIVE KEY QTY. PART NO. DESCRIPTION KEY QTY. PART NO. DESCRIPTION 2533-110 ¼ STRAIGHT SELF-TAP ZERK 6010-402 1/8 STRAIGHT SELF-TAP ZERK 6010-388 BOLT 6010-375 SCRAPER, R.H. INSIDE 6010-350 GEAR 6010-376 SCRAPER, L.H. INSIDE 6010-337 TUBE (CORN OR PEANUT) 6010-398 BUSHING 6010-323...
- Page 33 PARTS IDENTIFICATION CORN CUTOFF FOR SEED HOPPER QTY. PART NO. DESCRIPTION 6010-328 6010-319 ¼ X ¾ SCREW 6010-326 GATE 6010-413 COMPRESSION SPRING 6010-327 KNOCKER 6010-412 WHEEL 6010-348 DEFLECTOR 6010-374 BOTTOM, CORN 6010-332 PLATE, CORN 6010-337 TUBE 6010-330 RETAINER 6010-361 PLATE 6010-331 PLATE, STEEL, FLAT ON BOTH SIDES ………..
- Page 34 PARTS IDENTIFICATION PRESS WHEEL AND TIRES QTY. PART NO. DESCRIPTION 6010-385 TIRE, 4 X 16 CHEVRON (SUB FOR N10065) 2502-200 5/16-18 X ¾ HHCS GR 2 ZYD 2520-205 5/16 HEX LOCK NUT ZYD. 6010-394 2502-200 5/16-18 X ¾ HHCS GR 2 2525-201 5/16 MED LOCK WASHER ZYD 6010-353...
-
Page 35: Troubleshooting
TROUBLESHOOTING Problem Cause Solution Inaccurate drop Wrong seed plate Select proper seed plate Floor plate turned wrong side Turn floor plate over or select up or wrong false ring used. proper false ring. Knocker worn or not working Replace knocker. (Under cut- freely off cap) Chain on wrong sprockets... - Page 36 East, the South, the West and now north into Canada. We’re even getting orders from as far away as Australia and Africa. So, when you buy Yetter products . . .you’re buying a name that’s recognized. A name that’s known and respected. A name that’s become a part of American agriculture and has become synonymous with quality and satisfaction in the field of conservation tillage.
Need help?
Do you have a question about the 6010 Planter Unit and is the answer not in the manual?
Questions and answers