Allied Telesis AT-TQ4400e Quick Installation Manual

Quick Installation Guide
AT-TQ4400e
Outdoor Wireless Access Point
Installation and User's Guides
This document contains an abbreviated version of the installation instructions for the
AT-TQ4400e Wireless Access Point. For complete installation and management
instructions, refer to the AT-TQ4400e Installation Guide and AT-TQ Wireless Access Point
Series User's Guide on the Allied Telesis web site at www.alliedtelesis.com/support.
Safety and Electromagnetic Emissions Certificates
For Safety and Electromagnetic Emissions certificates, refer to the AT-TQ4400e Installation
Guide.
Installation Options
This quick installation guide explains how to install the device on a wall or pole.
Note
The non-US model of this product has a country code setting that must be set during
the initial management session of the unit. The setting ensures that the unit operates
in compliance with the laws and regulations of your country or region.
The country code for the US model is preset and cannot be changed. Per FCC
regulations, the country code setting for all WiFi products marketed in the US must be
fixed to US operational channels only.
Physical Description
For a physical description of the AT-TQ4400e Outdoor Wireless Access Point, refer to the
AT-TQ4400e Installation Guide.
Package Contents of the AT-TQ4400e Wireless Access Point
The following items should be in the shipping containers:
One AT-TQ4400e Wireless Access Point

This AT-TQ4400e Quick Installation Guide

Two 5GHz antennas

Two 2.4GHz antennas

One mounting base

One pole-mount bracket

One O-ring clamp

One ground cable

Two antenna connector caps

Four screws for the mounting base

Four screws for the pole-mount bracket

 One screw for the ground cable
If any item is missing or damaged, contact your Allied Telesis sales representative for
assistance. Retain the original shipping material in case you need to return the unit to
Allied Telesis.
*613-002196 Rev B*
613-002196 Rev. B
Attaching the Ground Cable to the Access Point
You must attach the ground cable before installing the device on a wall or pole. To attach
the ground cable to the access point, perform the following procedure:
1. Align the ground cable hole on the access point with the ring terminal of the ground
cable.
2. Drive the screw through the holes to attach the ground cable to the access point.
3. Cut off the extra length of the ground cable to make it connected straight to the
ground point.
4. Attach the other terminal of the ground cable to a circuit breaker, ground rod, or earth
ground.
Connecting the Access Point with the Ethernet Cable
To connect the access point with the Ethernet cable, perform the following procedure:
1. Unscrew the sealing nut at the LAN port on the access point and remove the
clamping claw and sealing insert.
2. Remove the rubber nail from the sealing insert.
3. Pass the LAN cable through the sealing nut, and attach the sealing insert and
clamping claw to the cable.
4. Connect the RJ-45 plug into the LAN port and screw the sealing nut to the access
point.
5. Connect the other RJ-45 plug to the PoE switch.
Installing the Access Point on a Concrete Wall
To install the access point on a concrete wall, perform the following procedure:
Note
To install the access point to a concrete wall, provide nuts, washers, and wall
anchors; to install the access point on a regular wall, provide four tapping screws.
1
1. Using the mounting base as a template, mark four holes with a pencil.
2. Pre-drill the marked locations on a concrete wall.
3. Install the four bolts and four wall anchors into the holes you made in Step 2.
4. Attach the mounting base to the access point with the screws using a Phillips-head
screwdriver.
5. Attach the nuts and washers to the bolts in the concrete wall to install the access
point to the wall.
Installing the Access Point on a Pole
To install to the access point to a pole, perform the following procedure:
1. Attach the mounting base to the access point with screws using a Phillips-head
screwdriver.
2. Attach the pole-mount bracket for installing to either a vertical or horizontal pole
using a Phillips-head screwdriver.
3. Attach the O-ring clamp to the pole-mount bracket.
4. Install the unit on the pole and tighten the O-ring clamp using the flat-head
screwdriver.
2 3