Related Manuals for Lanner LEC-7230M
Summary of Contents for Lanner LEC-7230M
- Page 1 Embedded & Industrial Computing Hardware Platforms for Embedded and Industrial Computing LEC-7230M V1.1 User's Manual Release date: 2016/11/28...
- Page 2 Resource Website installed and used in accordance with the instruction manual, may cause harmful interference to radio Lanner http://www.lannerinc.com communications. Operation of this equipment in a residential area is likely to cause harmful interference http://www.lannerinc.com/...
- Page 3 EMC Notice Operating Safety • Electrical equipment generates heat. Ambient air temperature may not be adequate to cool equipment to This equipment has been tested and found to comply acceptable operating temperatures without adequate with the limits for a Class A digital device, pursuant to Part circulation.
- Page 4 Consignes de sécurité pour refroidir l’équipement à une température de fonctionnement acceptable sans circulation adaptée. Suivez ces consignes pour assurer la sécurité générale : Vérifiez que votre site propose une circulation d’air adéquate. • Laissez la zone du châssis propre et sans poussière pendant et après l’installation.
- Page 5 Version Date (Y/M/D) Description 2015/08/03 Official release 2015/12/28 Modified DB9 COM port pin definitions...
-
Page 6: Table Of Contents
Connectors and Jumpers List Jumper and Connectors Pinouts Chapter 4: Hardware Setup Preparing the Hardware Installation Installing the System Memory Installing CompactFlash card Installing Mini-PCIe Module Installing SIM Card Installing the Disk Drive Wallmounting for LEC-7230M Appendix: Terms and Conditions... -
Page 7: Chapter 1: Introduction
System Specifications Introduction Intel® Celeron® J1900 (2M Cache, up to Processor Options 2GHz) (10W) Thank you for choosing Lanner LEC-7230M This product is a cost effective embedded system which adopts Intel Chipset None Bay-Trail CPU to provide a satisfying performance with... -
Page 8: Package Contents
Package Contents Your package contains the following items: LEC-7230M Fanless Embedded System • Power adapter • Drivers and User’s Manual CD • Ordering Information LEC-7230M-J11A Fanless Industrial PC with Intel® Celeron® J1900 2GHz Processor... -
Page 9: Block Diagram
Block Diagram... -
Page 10: Chapter 2: System Components
Chapter 2: System Components System Drawing Mechanical dimensions of the LEC-7230M Unit: mm... -
Page 11: Front Components
Front Components Component Description F1 Power On/Off Button Power the system on/off 1 x triple-stacked LEDs • Yellow for storage access status F2 LED indicators • Green for power-on status • the other green for 3G/4G/LTE status if a 3G/4G/LTE module is installed F3 Two LAN ports 2x RJ45 with LED connectors for 10/100/1000Mbps... -
Page 12: Rear Components
Rear Components Component Description R1 DC_IN 1x DC Jack W/lock for DC +12Vdc input 2 x DB9 Serial COM ports supporting RS- R2 Serial 232/422/485 R3 VGA 1 x VGA display port R4 HDMI 1 x HDMI 1.4a output WARNING: Improper installation can cause injury or property damage. For proper and safe operation use in field site with AC Power, please follow these instructions: 1. -
Page 13: Chapter 3: Board Layout
Chapter 3: Board Layout Jumpers & Connectors Locations JLPC1 DCJACK1 COM1,2 VGA1 JCMOS1 HDMI1 JCOM6 JRI1,2 JCOM5 SIM1 JSPI1 MPCIE1 DIMM1 JKBMS1 SATAPWR1 RSTBTN1 USB1 USB2 LOUT1 MIC1 LED1 LAN1,2 PSBTN1 SATA1... -
Page 14: Connectors And Jumpers List
Connectors and Jumpers List The tables below list the function of each of the board jumpers and connectors by labels shown in the above section. The next section in this chapter gives pin definitions and instructions on setting jumpers. Table 3.1 Connector List for LEB-7230M Board Labels Function COM1/COM2... -
Page 15: Jumper And Connectors Pinouts
Jumper and Connectors Pinouts JCOM5: RS-232 pin header JRI2: pin header for COM2 Pin9 signal selection Signal Pin No. Signal 1-2 short (Default) DCD# 3-4 short DSR# 5-6 short +12V RTS# CTS# JLPC1: LPC (Low-Pin-Count) pin header for debug uses DTR# JCOM6: RS-232 pin header Signal... - Page 16 JCMOS1: CMOS jumper to select “Normal” condition or to USB1: 1 x double-stacked USB 2.0 Type-A connectors clear CMOS setting Signal Signal Signal DATA1- 1-2 short (Default) Normal DATA1+ 2-3 short Clear CMOS DATA0- DATA0+ JKBMS1: PS/2 keyboard and mouse pin header USB2: 1 x USB 3.0 Type-A connector Signal Signal...
- Page 17 VGA1: 1 x VGA display port CF1: 1 x CompactFlash Type I/II slot Signal Signal GREEN BLUE Reserve DDC_DATA HSYNC Signal Signal VSYNC -CD1 DDC_CLK HDMI1: 1 X HDMI 1.4a display port -CS0 -CS1 A10 (GND) -VS1 ATA_SEL# -IORD A9 (GND) -IOWR A8 (GND) A7 (GND)
- Page 18 MPCIE1: 1 x Mini-PCIe socket (PCIexpress 1x and USB 2.0) SATA1: 1 x SATA 7-pin signal connector for 2.5” storage with SIM-card reader for 3G mini-card module device Signal Signal Signal WAKE# +3.3Vaux COEX1 COEX2 +1.5V CLKREQ# UIM_PWR UIM_DATA REFCLK- UIM_CLK REFCLK+ UIM_RESET...
-
Page 19: Chapter 4: Hardware Setup
It is strongly recommended to wear ESD proof gloves for the following setups. 1. Turn LEC-7230M upside-down. 2. Loosen the 4 locking pads circled in the image below and remove them from the bottom cover. 3. Press the module down until it is clipped in. -
Page 20: Installing Compactflash Card
Installing Mini-PCIe Module Installing CompactFlash card 1. Align the mini-PCIe module’s key with the Mini-PCIe Please follow the steps for installing CompactFlash card slot notch. 1. Align the female connector of your CF card to the male connector of the CF slot on the motherboard. 2. -
Page 21: Installing The Disk Drive
Installing the Disk Drive The system can accommodate one Serial-ATA disk drive. Follow these steps to install a hard disk into the system: 4. Your SATA disk drive should be placed as the image 1. Locate the disk drive bay on the back side of the top below. -
Page 22: Wallmounting For Lec-7230M
Wall Mounting for LEC-7230M LEC-7230M can be mounted on a wall for operational purposes. Please follow the steps below for wall mounting. 4. Apply 4 wall anchors based on the locations drawn in the last step. 1. Attach wall-mounting brackets to LEC-7230M. Align the brackets to the system by matching the screw holes circled below. -
Page 23: Appendix: Terms And Conditions
Appendix: RMA Service Requesting a RMA# Terms and Conditions 6. To obtain a RMA number, simply fill out and fax the “RMA Request Form” to your supplier. Warranty Policy 7. The customer is required to fill out the problem code as listed.