Recording From Another Vcr Or Camcorder; Tv System Conversion; Playback Conversion - Samsung SV-5000W Owner's Instructions Manual

Recording from Another VCR or Camcorder

GB
You can copy a cassette to your VCR from another video source
such as another VCR or a camcorder.
OUTPUT SYSTEM
THROUGH
/I STANDBY/ON EJECT REC
NTSC REW F.F
RESET
PAL
LINE 1 IN
VIDEO L AUDIO R SECAM
CHANNEL
PAL-M
P/S STOP
PAL-N
1
2
STROBE AUDIO
2
3
ART INPUT
5 6
2
CH
4
8 9
3
CLR/RST
0
4
REC P/STILL
STOP
5
6
DISPLAY 6 MONITOR A.DUB
7
REC P/STILL
STOP
7
DISPLAY MONITOR A.DUB
42
It is an infringement of copyright laws to copy prerecorded
cassettes or to re-record them in any form without the
permission of the owners of the corresponding copyright.
Connect the VCR from which the cassette is to be copied to the
appropriate RCA audio and video input connectors on the front of
your VCR, as indicated on page 40, 41.
If the other video source does not supply stereo sound,
connect only the left audio input (L).
You can also use a SCART cable to connect to the EURO
AV on the rear of your VCR.
Insert a blank cassette in your VCR.
Insert the pre-recorded cassette in the other video source (VCR or
camcorder).
Press the INPUT button to select the appropriate input on your
VCR:
LINE 1 or LINE 2 ; or
AV for the EURO AV.
Start playing back the cassette to be copied.
Press the REC button for at least one second to start recording on
your VCR.
When you have finished recording, press STOP ( ) on both
VCRs.
If you wish to view the cassette being copied:
your VCR must be connected as usual to the
television (see page 12 for further details) ; and
you must select the television AV input.

TV System Conversion

You can convert the input signal into the desired TV system.
1 Connect the RCA audio/video cable into the LINE 1 IN jacks on
the front of the VCR.
2 Press the INPUT SYSTEM button of the remote control to select
the input signal identification.
When the Auto mode is selected, the input signal is
automatically identified.
When the input signal is not automatically identified, select the
corresponding input system manually.
3
If you wish to convert the NTSC system into the PAL system,
select AUTO or NTSC system with the INPUT SYSTEM button on
the remote control.
Result: The display panel shows the NTSC input signal and
the NTSC output signal.
If the input signal does not correspond to the input
system of the VCR, an abnormal signal is outputted.
4 Press the PAL output button on the VCR.
Result: The display panel shows the NTSC input signal and the
PAL output signal, and the NTSC signal is converted
into the PAL signal for output.

Playback Conversion

You can perform playback conversion of the signal recorded on the
tape into the appropriate format for the country.
1
If you wish to convert the PAL system tape into the NTSC system
for playback, then press the NTSC output button on the VCR.
Result: The display panel shows NTSC output signal.
2
Insert the video tape into the VCR.
is shown on the display panel.
A video tape without the record protect (safety) tab intact will
playback automatically.
3
Press the PLAY ( ) button.
Result: TV system recorded on the tape is automatically read,
and the PAL signal is converted into the NTSC signal
for playback.
GB
LINE 1 IN
VIDEO AUDIO
L R
INPUT
SYSTEM
2
OK
THROUGH
NTSC
REW
4
PAL
SECAM
PAL-M
P/S
OUTPUT SYSTEM
THROUGH
1
NTSC
PAL
SECAM
3
REW F.F
43