Download Print this page

Cisco TX1300 47 Manual

Telepresence system, freestanding version.
Hide thumbs

Advertisement

Assembling the Cisco TelePresence
System TX1300 47—Freestanding Version
Revised: January 12, 2012, OL-24695-01
The following document describes the tasks that you perform to install and set up a freestanding version
of the Cisco TelePresence System TX1300 47 and includes the following sections:
The display used in this product contains mercury. Dispose of this display according to local, state, and
Note
federal laws.
Required Tools
CTS TX1300 47 Installation Video
A video that shows you the entire hardware installation process is available at the following URL:
http://www.cisco.com/en/US/docs/telepresence/cts_1300/cts_1300_47/assembly/guide/video/
cts1300_47_install_final_640_x_360.html
OL-24695-01
Required Tools, page 2-1
Assembling the TX1300 47, page 2-2
Connecting the Cisco TelePresence Touch 12 Device, page 2-20
#2 Phillips screwdriver
#3 Phillips screwdriver.
Long-handled #3 Phillips screwdriver, or a #3 Phillips drill bit that is at least 6 inches (15 cm) long
(for two of the screws that attach the cabinet to the base). See
3mm Allen wrench, ball-end recommended
Pen or pencil and paper (to write down the IP address when you power on the system)
Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide
2
C H A P T E R
Figure 2-3
for more information.
2-1

Advertisement

   Related Manuals for Cisco TX1300 47

   Summary of Contents for Cisco TX1300 47

  • Page 1

    System TX1300 47—Freestanding Version Revised: January 12, 2012, OL-24695-01 The following document describes the tasks that you perform to install and set up a freestanding version of the Cisco TelePresence System TX1300 47 and includes the following sections: • Required Tools, page 2-1 •...

  • Page 2

    Cabinet cover (CTS1300-47CABCOV) Seat alignment guides (CTS1300-SAG) Cable cover (CTS1300-47ACCKIT) Audio/visual (A/V) panel cover (CTS1300-47AV-CVR) Camera targets and easel (CTS-CAM-TOOL-G2) Not used for this configuration (wall-mounted systems only) Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide OL-24695-01...

  • Page 3

    Chapter 2 Assembling the Cisco TelePresence System TX1300 47—Freestanding Version Assembling the TX1300 47 Figure 2-1 Carton Contents Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide OL-24695-01...

  • Page 4

    If the system is not level, use the wrench that is provided in the kit to adjust the base feet to level the base. Figure 2-2 Attaching the Feet to the Base Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide OL-24695-01...

  • Page 5

    Note If using a power drill/screwdriver, set the torque to a setting of 5, 6, or 7. Figure 2-3 Attaching the Base to the Column Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide OL-24695-01...

  • Page 6

    (P/N 69-2179-01) and a #2 Phillips screwdriver. Note If using a power drill/screwdriver, set the torque to a setting of 5, 6, or 7. Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide OL-24695-01...

  • Page 7

    Alternatively, you can remove the paper before you install the light reflector. Note Figure 2-5 Attaching the End Caps and Light Reflector to the Cabinet and Removing the Protective Paper Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide OL-24695-01...

  • Page 8

    Remove the thumb screw from the light reflector and attach the processor to the light reflector using the thumb screw. See callout b in Figure 2-7 for more information. Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide OL-24695-01...

  • Page 9

    Cut the cable tie and release the cable in order to connect it to the camera processor. Figure 2-7 Inserting the Camera Processor Into the Light Reflector Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide OL-24695-01...

  • Page 10

    Connect the power and signal cables to the back of the display. Rotate the display downwards until the lower part of the display attaches to the light reflector. Figure 2-8 Attaching the Display to the Light Reflector Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide 2-10 OL-24695-01...

  • Page 11

    Figure 2-9 Attaching the Camera and Camera Cables to the Light Reflector and Camera Processor Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide 2-11 OL-24695-01...

  • Page 12

    If you use a HGMI-to-HDMI, HDMI-to-DisplayPort, or HDMI-to-Mini Displayport cable, use the audio connection labeled “Aux” on the codec. Figure 2-12 shows both connections. Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide 2-12 OL-24695-01...

  • Page 13

    Chapter 2 Assembling the Cisco TelePresence System TX1300 47—Freestanding Version Assembling the TX1300 47 Figure 2-10 (Figure 1 of 4) Attaching the Codec Brackets to the Codec Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide 2-13 OL-24695-01...

  • Page 14

    Chapter 2 Assembling the Cisco TelePresence System TX1300 47—Freestanding Version Assembling the TX1300 47 Figure 2-11 (Figure 2 of 4) Inserting the Codec Into the Cabinet Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide 2-14 OL-24695-01...

  • Page 15

    Chapter 2 Assembling the Cisco TelePresence System TX1300 47—Freestanding Version Assembling the TX1300 47 Figure 2-12 (Figure 3 of 4) Connection Diagram for TX1300 47 Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide 2-15 OL-24695-01...

  • Page 16

    Chapter 2 Assembling the Cisco TelePresence System TX1300 47—Freestanding Version Assembling the TX1300 47 Figure 2-13 (Figure 4 of 4) Routing the External Microphone and VGA Cables Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide 2-16 OL-24695-01...

  • Page 17

    Attach the compliance label to the inside left of the cabinet. Attach the codec cabling diagram to the inside of the cable cover. Attach the cabinet cover to the system. Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide 2-17 OL-24695-01...

  • Page 18

    Chapter 2 Assembling the Cisco TelePresence System TX1300 47—Freestanding Version Assembling the TX1300 47 Figure 2-15 Attaching the Cabinet Cover Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide 2-18 OL-24695-01...

  • Page 19

    The notched edge of the A/V panel cover should slide underneath the top light, and cover the rear half of the top opening of the light reflector. Figure 2-16 Attaching the A/V Panel Cover Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide 2-19 OL-24695-01...

  • Page 20

    Cisco TelePresence Touch 12. See Figure 2-12 for information about the codec connections. Figure 2-17 Connections On the Cisco TelePresence Touch 12 Cisco Touch Codec Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide 2-20 OL-24695-01...

Comments to this Manuals

Symbols: 0
Latest comments: