Performance Tests For Fluke 10 - Fluke 10 Service Manual

Test Meter Range
No.
1 4.000V AC
2 4.000V AC,MIN MAX*
3 4.000V AC
4 4.000V AC
5 4.000V AC
6 4.000V AC
7 40.00V AC
8 40.00V AC
9††† 400.0V AC
10 600V AC
11 4.000V DC,MIN MAX*
12 4.000V DC
13 40.00V DC
14 400.0V DC
15 4.000V DC
16 40.00V DC
17 400.0V DC
18 600V DC
19 Continuity
20 Continuity, VCHEK
21 Continuity, VCHEK
22 400.0Ω
23 400.0Ω
24 400.0Ω
25 4.000 kΩ
26 40.00 kΩ
27 400.0 kΩ
28 4.000 MΩ
29 40.00 MΩ
Ω, VCHEK
30
31†† 1.000µF
32†† 1.000µF
* MIN MAX tests are for Fluke 12 only.
** Calibrator 50Ω divider override.
† The dc volts annunciator must be on.
Conducting performance tests of the 400Ω, 4 kΩ, 40 kΩ, and 1 µF ranges (tests no. 22, 23, 24,
††
25, 26, 31, and 32) verifies that the discrete and integrated circuitry needed to support the other
capacitance ranges are working within specifications. Therefore, these tests indirectly verify that the
meter will meet specification in the 10 µF, 100 µF, 1000 µF, and 10,000 µF ranges.
††† In the V-CHEK mode, the UUT uses a low-impedance thermistor (approx. 2.5 kΩ) for circuit
protection and load testing (referred to as lo-Z input circuitry). When using the 5100B or 5700A to drive
the UUT with higher voltages, avoid an overload/current limit condition by gradually stepping the voltage
up (waiting two seconds between each step) from 90.0V, 120.0V, 180.0V and 350.0V at 80 Hz each step.
Table 3-3. Performance Tests for Fluke 11 and 12
Input To
Meter
0V
0V
10 mV, 50 Hz
10 mV, 400 Hz
3.5V, 50 Hz
3.5V, 400 Hz
35V, 50 Hz
35V, 400 Hz
350V, 80 Hz
600V, 400 Hz
0V
0V
+20 mV DC
-200mV DC
+3.5V
-35V DC
+100V DC
-600V DC
+2V DC**
+3.43V DC**
-0.5V DC**
0.0Ω
1.0Ω
350.0Ω
1.0 kΩ
35 kΩ
100 kΩ
2.9 MΩ
35 MΩ
1.96V DC
0.0µF
0.95µF
Slide-Switch Display
Position Minimum
Center 0.000
Center 0.000
Center 0.007
Right 0.007
Right 3.430
Center 3.430
Center 34.30
Right 34.30
Right 343.0
Center 586
Center -0.012
Right -0.002
Right 00.01
Center -000.3
Center +3.466
Center -35.33
Center +99.0
Center -606
Right 1.980
Right 3.397†
Right -0.507†
Right 0.0
Right 0.8
Right 346.6
Right 0.990
Right 34.67
Right 99.0
Right 2.873
Right 34.44
Right 1.940†
Right -0.001µF
Right 0.93µF
Maintenance 3
Calibration
Display
Maximum
0.003
0.040
0.013
0.013
3.570
3.570
35.70
35.70
357.0
614
0.012
0.002
00.03
-000.1
+3.534
-34.67
+101.0
-594
2.020
3.463†
-0.493†
0.2
1.2
353.4
1.010
35.33
101.0
2.927
35.56
1.980†
0.001µF
0.970µF
3-9