Shinko PCB1 Instruction Manual

PCB1 Key Operation Flowchart

POWER ON
RUN Mode
(*)
RUN
Monitor Mode
Program control Program control
Stop(in standby) RUN
PTN
STOP
(1 sec)
(*) Select a pattern with PTN, and press RUN.
Program control for the pattern will be performed.
Setting Mode
MODE
Pattern Setting Mode Event Setting Mode
MODE MODE
Step 1 time
Time
00: 0 0
MODE MODE
MODE MODE
Step 2 SV
Temp
///0
MODE MODE
Setting items for
Step 2 to 10 appear.
MODE
MODE
MODE MODE
Returns to the 1st item.
PTN/STEP Display indicates
MODE
the selected pattern number.
Returns to the 1st item.
PTN/STEP indicator is unlit.
PTN/STEP Display indicates the
selected pattern number.
PTN/STEP indicator lights up the
step number.

Initial Setting

Before pattern setting and Event setting, perform initial setting as follows.
• Engineering setting mode 2: to
• Control parameter setting mode:
Pattern link Lock 5
Loc5
Pattern link Disabled Changeable in Set value lock
----
Pattern link Enabled Step SV + Step time
chin Sv//
AT Perform / Cancel
Step SV + Step time + EV
svev
AT Cancel value
----
AT Perform Communication protocol
At//
OUT2 cooling method Shinko protocol
noml
Air cooling SV digital transmission (Shinko protocol)
Air/ Svt/
Oil cooling SV digital reception (Shinko protocol)
Oil/ svtr
Water cooling Modbus ASCII mode
Wat/ moda
Direct / Reverse action Modbus RTU mode
modr
Reverse control action Communication speed
heat
Direct control action 9600 bps
cool //96
Step 1 to 10 Wait function Enabled / Disabled 19200 bps
/192
Disabled 38400 bps
---- /384
Enabled Data bit / Parity
Use/
Set value lock 8 bits / No parity
8non
Unlock 7 bits / No parity
---- 7non
Lock 1 8 bits / Even
Loc1 8evn
Lock 2 7 bits / Even
Loc2 7evn
Lock 3 8 bits / Odd
Loc3 8odd
Lock 4 7 bits / Odd
Loc4 7odd
If no// (Data clear No) is selected: If
MODE is pressed, the unit returns to RUN mode.
If yes/ (Data clear Yes) is selected:
MODE
If MODE is pressed, the unit automatically
returns to RUN mode after data clear.
(Enabled during program control)
PTN PTN
Control Parameter Setting Mode
(*1)
MODE MODE
(*2)
MODE MODE
(*3) (*)
MODE MODE
(*3) (*)
MODE MODE
(*1) (*)
MODE MODE
(*)
MODE MODE
(*3)
MODE MODE
MODE
MODE
MODE MODE
MODE MODE
MODE MODE
Returns to the 1st item.
(*) PTN/STEP Display indicates
MODE
the PID block number.
PTN/STEP indicator is unlit.
Stop bit
1 bit
///1
2 bits
///2
Input type
alarm
K -200 to 1370 °C
k//C
K -200.0 to 400.0 °C
k/ . C
J -200 to 1000 °C
j//C
R 0 to 1760 °C
r//C
S 0 to 1760 °C
s//C
B 0 to 1820 °C
b//C
E -200 to 800 °C
e//C
T -200.0 to 400.0 °C
T/ . C
N -200 to 1300 °C
n//C
PL-II 0 to 1390 °C
Pl2C
C(W/Re5-26) 0 to 2315 °C
c//C
Pt100 -200.0 to 850.0 °C
Pt . C
JPt100 -200.0 to 500.0 °C
jpt. C
Pt100 -200 to 850 °C
Pt/C
JPt100 -200 to 500 °C
jptC
K -328 to 2498 °F
k//f
K -328.0 to 752.0 °F
k/ . f
J -328 to 1832 °F
j//f
r

About Setting Item

Upper left: PV Display: Indicates setting characters.
Step 1 SV
Temp
• Lower left: SV Display: Indicates factory default.
///0
Right side: Indicates setting items.
EV2 alarm value
• A2// Shaded setting items are optional, and appear only when the options are ordered.
///0
• (*1) Available when 001 (High limit) to 012 (H/L limits with standby independent) are selected in [Event output
EV allocation].
• (*2) Available when 004 (H/L limits independent), 006 (H/L limit range independent) or 012 (H/L limits with standby
independent) is selected in [Event output EV allocation].
• (*3) Available when 015 (Time signal output) is selected in [Event output EV
• (*4) Available when SV digital reception (Shinko protocol) is selected in [Communication protocol].
• (*5) Available when direct current or DC voltage input is selected in [Input type].
• (*6) Available when 001(High limit) to 012 (H/L limits with standby independent) – except [007 (Process high) and
008 (Process low)] – are selected in [Event output EV allocation].
Wait Parameter Setting Mode
Engineering Setting Mode 1
(*)
MODE MODE
MODE
(*)
MODE
MODE
(*)
MODE
Setting items for
MODE
Step 2 to 10 appear.
MODE
(*)
MODE
Returns to the 1st item. MODE
(*) PTN/STEP Display indicates
the selected pattern number.
MODE
PTN/STEP indicator lights up
the step number.
MODE
MODE
MODE
MODE
MODE
Returns to the 1st item.
PTN/STEP Display and
PTN/STEP indicator are unlit.
R 32 to 3200 °F 3 digits after decimal point
r//f 0. 0 00
S 32 to 3200 °F Event output EV1 to EV3 allocation
s//f
B 32 to 3308 °F No event
b//f /000
E -328 to 1472 °F High limit alarm
e//f /001
T -328.0 to 752.0 °F Low limit alarm
t/ . f /002
N -328 to 2372 °F H/L limits alarm
n//f /003
PL-II 32 to 2534 °F H/L limits independent alarm
Pl2f /004
C(W/Re5-26) 32 to 4199 °F H/L limit range alarm
c//F /005
Pt100 -328.0 to 1562.0 °F H/L limit range independent alarm
pt . f /006
JPt100 -328.0 to 932.0 °F Process high alarm
Jpt. f /007
Pt100 -328 to 1562 °F Process low alarm
Pt/f /008
JPt100 -328 to 932 °F High limit with standby alarm
jptf /009
4 - 20 mA -2000 to 10000 Low limit with standby alarm
420a /010
0 - 20 mA -2000 to 10000 H/L limits with standby alarm
020a /011
0 - 1 V -2000 to 10000 H/L limits with standby independent
0/1v /012
0 - 5 V -2000 to 10000 Heater burnout alarm output
0/5v /013
1 - 5 V -2000 to 10000 Loop break alarm output
1/5v /014
0 - 10 V -2000 to 10000 Time signal output
010v /015
Decimal point place Output during AT
/016
No decimal point Pattern end output
///0 /017
1 digit after decimal point Output by communication command
//0. 0 /018
2 digits after decimal point RUN output
/0. 0 0 /019
Key Operation
• Use and for settings, and register the settings with MODE or DISP.
• MODE:
• DISP:
• MODE (3 sec):
• +MODE:
• + (3 sec):
• +MODE (3 sec):
allocation].
• + +MODE (3 sec): Press
• + +STOP (3 sec): Press
• RST:
Engineering Setting Mode 2
MODE MODE
MODE MODE
MODE MODE
(*5)
MODE MODE
MODE MODE
(*6)
MODE MODE
(*1)
MODE MODE
(*1)
MODE
MODE
(*1)
MODE MODE
MODE MODE
(*6)
MODE MODE
(*4) (*1)
MODE MODE
Heating/Cooling control output
/020
Available only for Event output EV2 allocation
EV1 to EV3 alarm value 0 Enabled / Disabled
Disabled
No//
Enabled
Yes/
EV1 to EV3 alarm Energized / De-energized
Energized
noml
De-energized
revs
Event input DI1, DI2 allocation
No event
/000
Pattern number selection
/001
Direct / Reverse action
/002
Program control RUN / STOP
/003
Program control Holding / Not holding
/004
Program control Advance function
/005
Transmission output type
PV transmission
Pv//
SV transmission
Sv//
MV transmission
Mv//
Step time unit
Hours : Minutes
Min/
Minutes : Seconds
Sec/
Moves to the next item, illustrated by an arrow.
Moves back to the previous item (Opposite to MODE).
Press MODE for approx. 3 seconds.
Press and MODE (in that order) together.
Press and (in that order) together for 3 seconds.
Press and MODE (in that order) together for 3 seconds.
, and MODE (in that order) together for 3 seconds.
, and STOP (in that order) together for 3 seconds.
Returns to RUN mode from any setting items.
(*1)
MODE
(*1)
MODE
MODE
(*6)
MODE
(*1)
MODE
(*1)
MODE
(*1)
MODE
MODE
MODE
Returns to the 1st item.
PTN/STEP Display and
PTN/STEP indicator are unlit.
Power restore action
Stops after power is restored
stop
Continues after power is restored
cont
Suspends after power is restored
hold
Program control start type
PV start
Pv//
PVR start
Pvr/
SV start
Sv//
Output status when input errors occur
Output OFF
Off/
Output ON
On//
Error indication
Disabled
No//
Enabled
Yes/