Inscription Topic - Novus LogBox Wi-Fi Instruction Manual

7.2

INSCRIPTION TOPIC

When connected to a Broker, LogBox Wi-Fi can receive commands that will be answered through the novus/<sn>
seen below.
Commands in this topic can only be sent to the Broker if they have write permission enabled in the NXperience software
(see MQTT Protocol
*
novus/<sn> /command: Topic for receiving commands sent via MQTT.
•
Example: {"buzzer_state":0}
Command Type
anl1_spa_high Double
anl1_spa_low Double
anl2_spa_high Double
anl2_spa_low Double
anl3_spa_high Double
anl3_spa_low Double
dig_spa_high Double
dig_spa_low Double
buzzer_state Booleana
internal_clock Unix Timestamp or
TDateTime
set_download Unix Timestamp or
TDateTime
If successful, the device will send a message that can be viewed in the response topic novus/<sn>
Topic section of this chapter.
If there is any kind of error during the command request, the device will still send a response via the novus/<sn>
the type of error found, as described in Table 6.
Example:
Command: {"buzzer_state":0}
Answer: {"config_receive":"fail","error_type":"NOT_AUTHORIZED_ERROR","parameter":"buzzer_state"}
* The <sn> is the device serial number. That way, there will be no clash of topics in the Broker.
NOVUS AUTOMATION
section of the Configuration Software
Example
{"anl1_spa_high":10}
{"anl1_spa_low":0}
{"anl2_spa_high":10}
{"anl2_spa_low":0}
{"anl3_spa_high":10}
{"anl3_spa_low":0}
{"dig_spa_high":1}
{"dig_spa_low":0}}
{"buzzer_state":1}
{"internal_clock":1533294048}
If Unix format
{"internal_clock":43277.40465278}
If TDateTime format
{"set_download":1533294048}
If Unix format
{"set_download":43277.40465278}
If TDateTime format
Table 05 – Command list
chapter).
Description
Allows you to change the channel 1 higher alarm setpoint if the device is
configured to allow such a configuration (see
section of the Configuration Software
Allows you to change the channel 1 lower alarm setpoint if the device is
configured to allow such a setting (see
section of the Configuration Software
Allows you to change the channel 2 higher alarm setpoint if the device is
configured to allow such a configuration (see
section of the Configuration Software
Allows you to change the channel 2 lower alarm setpoint if the device is
configured to allow such a setting (see
section of the Configuration Software
Allows you to change the channel 3 higher alarm setpoint if the device is
configured to allow such a configuration (see
section of the Configuration Software
Allows you to change the channel 2 lower alarm setpoint if the device is
configured to allow such a setting (see
section of the Configuration Software
Allows you to change the higher alarm setpoint of the digital channel if the
device is configured to allow such a configuration (see
Parameters section of the Configuration Software
Allows you to change the lower alarm setpoint of the digital channel if the
device is configured to allow such a configuration (see
Parameters section of the Configuration Software
It informs the current state of the buzzer, according to the parameter
established in the Boolean settings of the sent command.
See the Boolean Format section of this chapter for more information about
Boolean types and formats.
Displays the device's internal clock.
This parameter must be written with the same Timestamp format defined in
NXperience.
See the Timestamp section of this chapter for more information on the
formats supported by the device.
Command used to request that LogBox Wi-Fi resend all logs from the
requested date in the "/log/channels" and "/log/event" topics (see
Topics section of this chapter).
This parameter must be written with the same Timestamp format defined in
NXperience.
See the Timestamp section of this chapter for more information on the
formats supported by the device.
*
/response, as described in the
*
/response topic, as can be
Analog Channels Parameters
chapter).
Analog Channels Parameters
chapter).
Analog Channels Parameters
chapter).
Analog Channels Parameters
chapter).
Analog Channels Parameters
chapter).
Analog Channels Parameters
chapter).
Analog Channels
chapter).
Analog Channels
chapter).
Logs
Response
*
/response topic, but it will inform
20/53