Advertisement
FH-SM12/SC12
Model
Image Sensor for FH - 12 Megapixel
Digital Camera
INSTRUCTION SHEET
Thank you for selecting OMRON product. This sheet pri-
marily describes precautions required in installing and
operating the product.
Before operating the product, read the sheet thoroughly to
acquire sufficient knowledge of the product. For your con-
venience, keep the sheet at your disposal.
TRACEABILITY INFORMATION:
Representative in EU:
Manufacturer:
Omron Europe B.V.
Omron Corporation,
Wegalaan 67-69
Shiokoji Horikawa, Shimogyo-ku,
2132 JD Hoofddorp,
Kyoto 600-8530 JAPAN
The Netherlands
NOTICE:
This product meets CISPR11 class A. The intended use of this product is in an
industrial environment only.
© OMRON Corporation
2014
All Rights Reserved.
PRECAUTIONS ON SAFETY
Meaning of Alert Symbols
Indicates a potentially hazardous situation which, if
not avoided, will result in minor or moderate injury,
WARNING
or may result in serious injury or death. Additionally
there may be significant property damage.
Alert statements
WARNING
This product is not designed or rated for ensuring safety
of persons. Do not use it for such purposes.
PRECAUTIONS FOR SAFE USE
Be sure to respect following items for safety.
・ Tighten all screws securely during installation.
・ Do not connect the Sensor to the products other than the dedicated camera cable
(FZ-VS□□), controller (FH), lighting controller (FL-TCC1 and FLV-TCC□),
extension unit (FZ-VSJ). If the Sensor is connected to non-dedicated products and
turned the power on, the devices may be damaged and be heated to a high
temperature.
・ If you suspect an error or malfunction, stop using the Controller immediately, turn
OFF the power supply, and consult your OMRON representative.
・ Do not try to disassemble, repair, or modify the product.
・ Be sure to dispose of the product as industrial waste.
PRECAUTIONS FOR CORRECT USE
Please observe the following precautions to prevent failure to operate, malfunction, or
undesirable effect.
1. Installation and storage of the product
Do not install in the following locations.
・ Locations where the ambient temperature exceeds the rated temperature range.
・ Locations subject to sudden temperature changes (where condensation will form).
・ Locations subject to relative humidity outside the range of 35 to 85%.
・ Locations where there are corrosive or flammable gases.
・ Locations where there is dust, salt, or iron powder.
・ Locations where the device will be subject to direct vibration or shock.
・ Locations where there is strong scattered light.
・ Locations exposed to direct sunlight
・ Locations where there is splashing of water, oil, or chemicals.
・ Locations where there is a strong electrical or magnetic field.
・ Locations close to high-voltage devices and/or power devices
2. Cables
・ When connecting or disconnecting the camera cable or lighting controller cable, be
sure to turn off the controller unit.
・ Do not use the camera cable exceeding the specified length.
・ When connecting the Sensor and the Controller (FH) with single camera cable,
connect the cable to CH1 of the camera connector.
・ When connecting the Sensor and the Controller (FH) with two camera cables, the type
and length of the camera cable must be matched.
・ When connecting the Sensor and the Controller (FH) with two camera cables, check
the CH numbers of the Controller side and Camera side before connecting.
・ Up to three camera cables can be connected using the extension unit FZ-VSJ. Be
sure to use the recommended camera cable with FZ-VSJ.
・ When connecting the camera cable, tighten the cable with the fixing screw with the
recommended torque (0.15 N ・ m). Applying excessive force to the camera connector
may cause failure of the product.
・ Use the ferrite core equivalent to ZCAT2035-0930A (manufactured by TDK) at the
controller side of the camera cable.
・ The camera cable FZ-VS□□ has polarity. Be sure to connect the side with the name
plate on it to the controller. Be sure to connect the side with the name plate on it to
the controller.
3. Mounting
･Please tighten up securely by rated torque(M4 : 1.2N･m), when fixing the camera body.
･Please use an exclusive mounting bracket (Model : FH-SM12-XLC (separate sale)),
when fixing this product and dedicated lighting controller (Model : FL-TCC1 and
FLV-TCC□).
･Please tighten up securely by rated torque(M4 : 1.2N･m / M2 : 0.15N･m), when fixing
the camera body, the mounting bracket and dedicated lighting controller.
･Please use M42 mount exclusive lens (Model : 3Z4S-LE VS-L□□□□ /M42-10).
4. Beam
・ The beam center may vary for each camera. Be sure to confirm the center position of
the image using the monitor before mounting. In the nature of the materials used, the
beam center of this product may change for the number of pixels due to changes in
ambient temperature.
5. Maintenance
・ Avoid using thinner, alcohol, benzene, acetone or kerosene to clean the product.
・ If there is large dirt or dust attached to the imaging element, blow them off with
blower brush (for camera lens). Do not use your breath to blow the dust off.
・ When the lens is not mounted, be sure to attach the M42-mount cap on the lens mount. If dirt or
dust is attached to the image elements, false detection or failure may occur.
・ Be sure to attach a connector cap on unused connectors at the back of the camera.
Removing the connector cap may cause a foreign material entering in the camera,
causing false operation or failure.
・ Do not connect devices to the extension connector other than the dedicated ones
(FL-TCC1 or FLV-TCC□).
6. Imaging element
・ In the nature of imaging element, lines may appear in images due to measurement
conditions or gain setting value. This does not indicated a malfunction. Although
there may be multiple faulty pixels, this does not indicate a malfunction.
■
Ratings / Performance
General specifications
●
Model
FH-SC12
Item
FH-SM12
6.2 W max. (13 VDC)
Power consumption
Vibration
10 to 150Hz: half-amplitude: 0.35mm:(maximum acceleration: 50m/s
resistance
10 times for 8 minutes each in 3 directions
Shock resistance 150m/s
; 3 times each in 6 directions
Shock resistance
2
Operating: 0 to 40 ℃(with no icing nor condensation)
Ambient
Temperature
Storage: -25 to 65 ℃ (with no icing nor condensation)
Operating and storage: 35% to 85%
Ambient
humidity
(with no condensation)
Ambient
No corrosive gases
environment
Degree of
IEC60529 IP40 (in-panel)
protection
Center positional
X, Y : ±0.31mm
accuracy of
∂x, ∂y : ±1.7°
optical axis
Case: Aluminum
Materials
Weight
Approx. 320g
Accessories
Instruction Sheet (this sheet)
Cable length
High speed mode: 5 m max.
Standard mode: Using FZ-VS(L)4: 15 m max.
Using a dedicated product other
than FZ-VS(L)4: 10 m max.
Dedicated
FL-TCC1 , FLV-TCC□
lighting
(Connection with the lighting, be sure to be 10W, 0.9A
controller
or less to the total value of the power consumption of
the lighting controller. )
●Performance specifications
Model
FH-SC12
FH-SM12
Item
Picture element
Color CMOS
Monochrome CMOS
Corresponding to 1.76-inch
Corresponding to 1.76-inch
Effective pixels
4084(H)×3072(V)
Image size
22.5㎜×16.9㎜ (Diagonal 28.14㎜)
Pixel size
5.5 （ μm)×5.5(μm)
Scanning method
Progressive
High speed
2CH:38.9fps
mode※1
1CH:19.5fps
Frame
rate
Standard
2CH:19.5fps
mode※1
1CH:9.8fps
Synchronization method
Internal
Video output
Digital 8 bits
Gain
1 to 5 times
Shutter speed
60μs to 100,000μs
Partial scanning
4 line to 3072 line ( 4 line unit )
Operation indicator
Power ON : Green lighting／Power OFF : Black out
Number of camera
Max 4 camera per 1 FH controller(Can be connected to up to eight by
connections
combining the camera of FH-S □ 12 other than in connection 8CH controller)
Lens mounting ※2 M42 mount(Recommended lens : 3Z4S-LE VS-L□□□□/M42-10)
F mount(F mount adapter : FH-ADF/M42-10)
*1 This Sensor has high speed mode and standard mode according to your
application. High speed mode can be set in the system settings.
*2 For optical diagrams, refer to FH manual or catalog.
■
Connecting
●Camera
Using the Camera cable FZ-VS□□(sold separately), connect the connector
on the back of the camera and the camera connector on Controller FH series.
Camera cable
FZ-VS□□
Camera cable
connector CH1
Operation indicator
Name plate
* The camera cable FZ-VS□□ has polarity. Be sure to connect the side
with the name plate on it to the controller.
・ When connecting the product to the Controller with a single camera cable,
connect the cable to CH1 of the camera cable connector.
・ When connecting the product to the Controller with two camera cables,
connect it as shown below.
(connecting four Cameras)
Camera
Controller
FH-S□□□
FH
CH1
Camera connector 0
),
2
CH2
Camera connector 1
Camera connector 2
CH1
CH2
Camera connector 3
CH1
Camera connector 4
CH2
Camera connector 5
Camera connector 6
CH1
CH2
Camera connector 7
■Mounting about exclusive mounting bracket (Model : FH-SM12-XLC (separate sale))
There are the following two ways of use.
①Please use this bracket when fixing this product and dedicated lighting
controller (Model : FL-TCC1 and FLV-TCC□).
Please use M2 screws and tighten up securely by rated torque(M2 : 0.15N･m),
when fixing this product and dedicated lighting controller.
②Please use this bracket when fixing this product and the camera with
1/4-20UNC.
This bracket can be attached to all four sides of the direction of the camera.
Please use M4 screws and tighten up securely by rated torque(M4 : 1.2N ・ m)
※The camera body is recommending installation by a screw hole of the body.
It's isn't necessary to use FH-SM12-XLC.
■Dimensions
（Unit ： mm）
4-M2.6 DEPTH5
(for F mount adapter)
4-M4 DEPTH5
M42xP1.0
(M42 MOUNT)
IMAGE AREA
43.6
OPTICAL AXIS
58
68
4-4.5Dia.
58 ±0.1
MOUNTING SCREW HOLES
Camera cable
FH-S□12 camera body is recommending installation by a screw hole of the body.
connector CH2
5 mounting surface of the bottom front, top, and both sides are possible.
( Rated torque M4 ： 1.2N･m／M2.6 ： 0.3N･m)
Suitability for Use
Enhancing connetor
Omron Companies shall not be responsible for conformity with any standards,
codes or regulations which apply to the combination of the Product in the
Buyer's application or use of the Product. At Buyer's request, Omron will
provide applicable third party certification documents identifying ratings and
limitations of use which apply to the Product. This information by itself is not
sufficient for a complete determination of the suitability of the Product in
combination with the end product, machine, system, or other application or
use. Buyer shall be solely responsible for determining appropriateness of the
particular Product with respect to Buyer's application, product or system.
Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING
SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE
SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL
EQUIPMENT OR SYSTEM.
See also Product catalog for Warranty and Limitation of Liability.
OMRON Corporation
Tokyo, JAPAN
Contact: www.ia.omron.com
Regional Headquarters
OMRON EUROPE B.V.
Sensor Business Unit
Carl-Benz-Str. 4, D-71154 Nufringen, Germany
Tel: (49) 7032-811-0/Fax: (49) 7032-811-199
OMRON ELECTRONICS LLC
2895 Greenspoint Parkway, Suite 200
Hoffman Estates, IL 60169 U.S.A.
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark,
Singapore 119967
Tel: (65) 6835-3011/Fax: (65) 6835-2711
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120, China
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200
s
D
O ct, 2 014
4-M4 DEPTH5
5
31
40
8
36
4-M4DEPTH5.0
Operation
5
31
indicator
（5）
40
5
31
4-M4 DEPTH5
4-4.5Dia.
31 ±0.1
MOUNTING SCREW HOLES
Industrial Automation Company
Advertisement
