Related Manuals for Baier BDS 125 N
Summary of Contents for Baier BDS 125 N
- Page 1 Instruction Manual BAIER Wet Concrete Cutter / Chaser BDS 125 N Maschinenfabrik OTTO BAIER GmbH Heckenwiesen 26 D-71679 Asperg Tel. +49 (0) 7141 30 32-0 Fax +49 (0) 7141 30 32-43 info@baier-tools.com www.baier-tools.com...
-
Page 2: Table Of Contents
Contents Contents ............................ 2 Important Information ......................2 Pictograms ..........................3 Explanation of the pictograms on the wet concrete cutter / chaser ........3 Explanation of the pictograms used in the text ............... 3 For your Safety ......................... 4 General safety instructions for power tools ................4 1) Safety at the place of work .................... -
Page 3: Pictograms
Pictograms Explanation of the pictograms on the wet concrete cutter / chaser The CE mark on a product means that the product conforms with all the applicable European regulations and has been subjected to the prescribed conformity assessment procedures. Environmentally friendly disposal of waste equipment Waste equipment contains valuable recyclable materials which should be reused or recycled. -
Page 4: For Your Safety
For your Safety General safety instructions for power tools WARNING Read all the safety instructions and precautions. Failure to observe the safety instructions and precautions can result in electric shock, fire and/or serious injuries. Keep all safety instructions and precautions for future reference. The term “power tool”... -
Page 5: Safety Of People
For your Safety 3) Safety of persons Always work carefully, attentively and sensibly when using a power tool. Do not use power tools if you are tired or are under the influence of drugs, alco- hol or medication. A moment of inattention while using the power tool can result in serious injuries. Wear personal protective equipment and always wear goggles. -
Page 6: Service
For your Safety Store power tools out of the reach of children when not in use. Do not allow people to use the tool unless they are familiar with it, or if they have not read this instruction manual. Power tools are dangerous if they are used by inexperienced people. Maintain power tools with care. -
Page 7: Electrical Safety
Asbestos-containing material may only be machined by specialists. − Wherever possible, use a dust extractor suitable for the material you are working on (e.g. a special BAIER dust extractor). − Ensure the workplace is properly ventilated. − We recommend wearing a face mask respirator with filter class P2 or P3 (to EN 149:2001). -
Page 8: Safety Of People
(e.g. a special BAIER dust extractor). Anti-vibration safety gloves At a release value A (8) for arm-hand vibrations of over 2.5 m/s , the wearing of anti-vibration safety gloves is recommended. -
Page 9: Hazards When Using And Handling The Power Tool
For your Safety Hold the tool at the insulated gripping surfaces only when carrying out work during which the insert tool can hit concealed electricity cables or the tool's own mains power lead. Contact with a live conductor can also energise metal parts of the tool and cause an electric shock. - Page 10 The machines can be very hot after use, do not touch the parts, risk of injuries. Additional signs or other, non BAIER-specific parts may not be screwed or riveted onto the motor, handle, gearbox or protective housing. This could damage the power tool and cause malfunctions.
-
Page 11: Service / Maintenance / Repair
Otherwise, all liability and warranty claims against Maschinenfabrik OTTO BAIER GmbH expire. Ensure that original BAIER spare parts and original BAIER accessories only are used when needed. Original parts are available from authorised dealers. Use of non original parts can cause damage to the machine and an increased risk of accidents. -
Page 12: Technical Characteristics
Intended Use Provided it is fitted with the appropriate grinding disc for the material to be machined, the BDS 125 N wet concrete cutter / chaser is suitable for the following uses: • for cleaning and smoothening hard surfaces, • for removing formwork joints and slurry skins in concretework, •... -
Page 13: Machine Parts And Controls
10 Front handle 11 Spindle lock button 12 Personal protection switch PRCD Tools and Accessories • Metal transport case for BDS 125 N ID No. 67942 • BAIER guard plate for BDS 125 N ID No. 71464 • BAIER water pressure vessel ID No. -
Page 14: Before Starting Work
• Only use the grinding discs recommended by Maschinenfabrik OTTO BAIER GmbH for the respective use (see table on page 13). • Please note! We can only guarantee the machine's full performance if it is used with the BAIER dust extractor. • Danger! Risk of fire if cable drums used. -
Page 15: Adjusting The Front Handle
Before Starting Work (Figure 1) Adjust the front handle Figure 1 To enable comfortable handling of the machine, the tilt of the front handle (1) can be adjusted. • Use the Allen key SW8 to undo the two hex socket cap screws (1). •... -
Page 16: Operation And Control
Operation and Control (Figure 3) Fit or replace wet grinding disc Choose a grinding teller suitable for the material to be machined and the required abrasion (see table on page 13). Danger! Risk of fatal injuries due to electric shock. ►... -
Page 17: Adjusting The Cutting Depth
• Check the dust extractor is working properly and then push the dust extractor hose (3) firmly onto the socket (1). • The socket (1) is designed for the suction hose of all BAIER special dust extractors. • Please note! Greater effort may be required to push on the suction hose in cold ambient tempera- tures. -
Page 18: Adjust Water Supply
Operation and Control (Figure 7) Adjust water supply Figure 7 • Danger! Risk of injury due to electric shock. ► Protect the machine against water splashes. When inserting and removing the water hose, ensure that no water penetrates the air slits of the machine. Use in- tact Gardena couplings and Gardena hose lengths only. -
Page 19: Finish Cutting Process
Operation and Control • Carefully position the wet concrete cutter / chaser on the surface to be machined. • The surface is machined with circular or linear movements, while the wet concrete cutter / chaser is guided over the surface to be machined with only a moderate pres- sure. -
Page 20: Cleaning
Only servicing and repair firms authorised by Maschinenfabrik OTTO BAIER GmbH may carry out maintenance of the machine. Also ensure that original BAIER spare parts and original BAIER accessories only are used. -
Page 21: Warranty
Servicing and cleaning work are not generally covered by the warranty. 4. Use of original BAIER spare parts Ensure that original BAIER spare parts and BAIER accessories only are used. They are available from authorised dealers. The type and quantity of grease are to be used according to the valid grease list. - Page 24 Maschinenfabrik OTTO BAIER GmbH Heckenwiesen 26, D-71679 Asperg Tel. +49 (0) 7141 30 32-0 Fax +49 (0) 7141 30 32-43 info@baier-tools.com www.baier-tools.com BAIER S.A.R.L. OTTO BAIER Italiana S.r.l. BAIER Scandinavia Aps 48, rue du Docteur Basset Via della Liberazione 21 Hammerbakken 12 –...