Set Date; Set Time; Display Accumulator; Count Display Mode - Rice Lake 520 Installation Manual

To display a checkweigh value, enter front panel setup
mode. Press or
DOWN ENTER
checkweigh value is displayed. The
keys will toggle through each checkweigh value that
is operator accessible. Press
checkweigh value.
To change the checkweigh value, use the
keys to increment/decrement the decimal value of the
ENTER
flashing digit. Press
LEFT/RIGHT
decimal point entry.
decimal point placement. Press the
accept the displayed value and return to the next value
or checkweigh value prompt.
Some indicator configurations may not allow
NOTE:
checkweigh values to be changed through the front
panel or may require a password to display or change
the checkweigh value.
1.3.12

Set Date

In front panel setup mode use the arrow keys to toggle
Date
to . Press or
DOWN
the format configured for the indicator: MMDDYY,
DDMMYY, or YYMMDD.
1.3.13

Set Time

In front panel setup mode use the arrow keys to toggle
Time
to . Press or
DOWN
24-hour format, then press the
1.3.14

Display Accumulator

The accumulator must be enabled before use in either
normal mode or setpoint operations. Once enabled,
weight (net weight if a tare is in the system) is
accumulated whenever a print operation is performed
using the key, digital input, or serial command.
PRINT
The scale must return to zero (net zero if a tare is in
the system) before the next accumulation.
1. Press and hold the
t o d i s p l a y t h e a c c u m u l a t e d va l u e i f
accumulator is enabled.
2. Press the key to clear the accumulator or
UP
the PRINT key to print the accumulator.
The key will only perform one
NOTE: PRINT
accumulation. Weight must return to zero before
another accumulation is allowed.
1.3.15

Count Display Mode

Count mode is entered by pressing the MODE
(GROSS/NET) key from normal weighing mode
when count mode is enabled. In count display mode,
the display shows the number of parts rather than
weight. The annunciator at the right side of the LCD
display reads piece count (PC). Pressing the PRINT
key sends the CFMT print format data string to the
serial port.
4 520 Installation Manual
and the first available
LEFT/RIGHT
to display the
ENTER
UP/DOWN
to sequence to the
keys adjust the
ENTER
key to
to enter the date in
ENTER
to enter the time in
ENTER
key.
ENTER
key for three seconds
G/N
If a sample weight has not yet been acquired, the
indicator switches automatically to sample acquisition
mode (see Section 6.0 on page 42).
1.3.16

Peak Hold Mode

The peak hold function is used to determine, display,
and print the greatest net weight read during a
weighing cycle.
A weighing cycle ends when the print command is
given, or when the peak net weight is manually
ZERO
cleared by the key. Peak hold tracks only net
weight and operates independently of the display. For
example, if the indicator is displaying gross weight,
but AUTO peak hold is active, the display will remain
in gross, but the net peak weight will be automatically
printed when standstill is achieved at net zero.
Peak hold function is enabled in the setup mode.
Parameter settings are found under the PK HOLD
submenu, in first level program menu.
Normal (Positive Peak, Manual Reset)
This is the basic peak hold function in which a weight
is applied to a scale and the greatest net weight value
is held in memory until the weight is removed from
the scale, and either the
pressed. If the display is in gross mode, the peak net
weight can be displayed by toggling to the net mode
G/N
with the key.
Bi-Dir (Bi-Directional Peak, Manual Reset)
This is the same as NORMAL parameter setting
(above), except that the peak can either be a positive
or negative number, determined by the absolute
weight value. This means that if a positive peak is
displayed, a negative weight value of greater absolute
value can update the peak information in the same
cycle. As above, the peak cycle is reset by pressing the
ZERO
key after the weight has been removed.
Auto (Positive Peak, Auto Print, Auto Reset)
This is the same as NORMAL parameter setting
(above), except that automatic print occurs when the
scale load is reduced to 0 ± 10 display divisions and
the scale achieves standstill. Following the print
command, the peak value is cleared and reset
automatically. As in the above two modes, the peak
hold value can also be cleared by the
PRINT
a manual press of the
The digital display can be set to display gross weight
information data using the
hold function cycles.
ZERO
or key is
PRINT
ZERO
key, or by
key.
G/N
mode key during peak