Table of Contents
Advertisement
K. TESTING THE OPERATION OF THE LOCK
K-1 Rotate inside lever and hold. Ensure that the mortise latch is fully retract-
ed and flush with the mortise faceplate. Release the inside lever; the latch
should be fully extended.
K-2 Enter the factory-set combination: 1,2,3,4,5,6,7,8. You should see a green
light and hear a high-pitched tone as you push each button. When the lock
opens you will briefly hear the sound of an electric motor. If 1,2,3,4,5,6,7,8
does not seem to work, please follow the steps to perform a hard reset by
following the procedure in section L.
K-3 Rotate outside lever and hold. Ensure that the latch is fully retracted and
flush with the latch faceplate. Release the outside lever; the latch should
be fully extended. When the lock re-locks, you will again hear the motor.
K-4 Insert key into the outside lever. Rotate key counterclockwise to stop posi-
tion and hold. Ensure that the latch is fully retracted and flush with the
latch faceplate. Rotate the key clockwise to the horizontal position and
remove the key. The latch should be fully extended.
K-5 To test the deadbolt function (where applicable), turn the thumbturn knob
to extend the deadbolt. A red light should flash once. Then, turn the
thumbturn again and verify that the deadbolt is retracted and there is a
flash of the green light.
Note: Refer to the Operating Manual to set up lock operation.
L. RESET FUNCTION
Warning: When the lock is reset, all existing authorization and access codes
are deleted, and the lock is configured to the factory default lock settings.
The master code becomes 1,2,3,4,5,6,7,8.
If the Master Code is lost or forgotten and the number has not been recorded,
the lock can be reset to the factory defaults by following this procedure:
1) Insert key, turn to "Open" position and hold.
2) Within five seconds, push "#" button on lock and then release the key.
3) Red and green lights should begin flashing.
4) Input 1,2,3,4,5,6,7,8,# at lock within 10 seconds.
5) You should hear the sound of lock resetting and a high-pitch tone.
6) Green light flashes. Lock is set to factory mode.
Note: For security reasons, all existing audit events are not deleted.
The lock is now set to the factory-configured setup with the default factory
master code, 1,2,3,4,5,6,7,8. Important: Before you can program the lock, you
must first enter a new 8-digit master code of your choice.
14
For example, if your new code is 1,2,,7,2,4,6,8, the correct buttons to press in
the exact order are:
#1,2,3,4,5,6,7,8,#,0,0,0,#,1,3,5,7,2,4,6,8,#,#. To determine if you have successful-
ly changed your master code, enter 1,3,5,7,2,4,6,8, and the lock should open.
Now try the factory master code, 1,2,3,4,5,6,7,8 and the lock should not open.
Refer to the included Operations Manual for further programming instructions.
M. INSTALLING RUBBER BUMPERS
M-1 Close the door and apply pressure making sure
the deadlatch (a) rests on the strike plate (b) as
shown. Standing on the frame (door step)
side of the door, check for gaps between the
door and the frame on the three sides of the
frame (left, right and top).
M-2 Mark locations where the gaps are
approximately
⁄
" (5 mm). Make sure
3
16
these locations are free from grease and
dust. Peel the bumpers (c) (supplied) from
their protective backing without touching
the adhesive surface and stick them on the
marked locations.
Note: Allow 24 hours for bumper adhesive to
set before testing. The door may be operated
manually during this time.
Correct
a
b
Incorrect
a
b
c
15
Advertisement
Table of Contents
