Page 1
AX1240S-AP-0202C_R2X Software Manual Corrections (For Ver. 2.2.C/2.2.D/2.2.E) Released September 2010 (Edition 3)
Page 2
This document contains corrections for the AX1250S/AX1240S series software manuals (Copyright (c) 2008, 2010 ALAXALA Networks Corporation. All rights reserved.). When you read a manual listed in the following table, please also read this document. The table below lists the AX1250S/AX1240S series software manuals to which the corrections in this document apply.
Page 3
AX1240S-AP-0202C_R2X History of amendments (Edition 3) Item Location and title Changes Configuration Guide Vol. 1 Corrections have been added to the filter conditions that can be assigned to the IPv4 access list used for authentication. The RADIUS server group has been added to the login authentication options. Configuration Guide Vol.
AX1240S-AP-0202C_R2X Changes in Configuration Guide Vol. 1 (For Version 2.2) (AX1240S-S001-30X) 3. Switch Capacities 3.2 Switch Capacities (13) Layer 2 authentication functionality [Change] The filter conditions that can be specified for the IPv4 access list used for authentication in Table 3-24 Other capacity limitations regarding Layer 2 authentication –...
Page 6
AX1240S-AP-0202C_R2X 8. Login Security and RADIUS 8.2.3 Authentication via RADIUS (1) Selection of login authentication service [Change] The RADIUS server group has been added to the options for login authentication services. [Ver. 2.2.E and later] Correlation diagram of authentication method configuration has been added in front of Figure 8-7 Authentication method sequence.
Page 7
AX1240S-AP-0202C_R2X <group-name> (RADIUS server group authentication) in the above figure, because both methods are group treated as the RADIUS authentication service. Use either of them in combination with local password authentication. The following figure shows the authentication method sequence used if RADIUS and local password authentication are specified in this order.
Page 8
AX1240S-AP-0202C_R2X 10. Power saving Functionality 10.1 Implementing power saving 10.1.5 Cooling fan control functionality [Change] Descriptions of this section have been corrected as follows: Before the change: This functionality monitors the temperature in the Switch, and if the Switch is located in a favorable environment that does not require forced cooling, it stops the cooling fan.
Page 9
AX1240S-AP-0202C_R2X 12. Ethernet 12.8 Gigabitethernet (SFP) 12.8.1 Functionality [Change] Table 12-24 Flow control operation determined by the auto-negotiation result in (4) Flow control has been corrected as follows: Before the change: Table 12-24 Flow control operation determined by the auto-negotiation result The Switch Remote device Result of auto-negotiation...
Page 10
AX1240S-AP-0202C_R2X desired After the change: Table 12-24 Flow control operation determined by the auto-negotiation result The Switch Remote device Result of auto-negotiation Flow control operation on the Switch Send Receive Send Receive Send Receive Is sending Is sending pause pause pause pause pause...
AX1240S-AP-0202C_R2X Changes in Configuration Guide Vol. 2 (For Version 2.2) (AX1240S-S002-40X) 4. Send Control 4.1 Overview of the shaper 4.1.3 Scheduling [Addition] Descriptions have been added to Table 4-4 WFQ configuration range as follows: Before the change: Table 4-4 WFQ configuration range Line speed Bandwidth Configuration range...
Page 12
AX1240S-AP-0202C_R2X #2: For values greater than 1000 K, set them in 100 K increments (1000 K, 1100 K, 1200 K...10000000 K). #3: For values that are less than 1000 K, set them in 64 K increments (64 K, 128 K, 192 K...960 K). 4.1.4 Port bandwidth control [Change] The descriptions of Table 4-5 Configuration values for port bandwidth control have been corrected as follows: Before the change:...
Page 13
AX1240S-AP-0202C_R2X #2: For values greater than 1000 K, set them in 100 K increments (1000 K, 1100 K, 1200 K...10000000 K). #3: For values that are less than 1000 K, set them in 64 K increments (64 K, 128 K, 192K...960 K). The range of frames for port bandwidth control is from the MAC header to the FCS.
Page 14
AX1240S-AP-0202C_R2X After the change: Table 6-4 Operational conditions of IEEE 802.1X Category Configuring Specifiable Frame Port-based Port-based VLAN-based ports VLAN type type authentication authentication authentication (static) (dynamic) (dynamic) Port type Access port native Port VLAN Untagged MAC VLAN Trunk port native Port VLAN Untagged...
Page 15
AX1240S-AP-0202C_R2X 7. IEEE 802.1X Configuration and Operation 7.4 Configuring port-based authentication (dynamic) 7.4.2 Configuring authentication mode options [Change] In (1) Configuring authentication exclusion options, Configuration command example has been corrected as follows and notes have been added. Before the change: Configuration command example (config)# mac-address-table static 1234.5600.e001 vlan 200 interface fastethernet Adds the MAC address (...
Page 16
AX1240S-AP-0202C_R2X 8. Description of Web Authentication 8.1 Overview [Change] Descriptions of this section have been corrected as follows. In addition, Table 8-2 Operating conditions for Web authentication has been corrected as follows: Before the change: In Web authentication, user authentication is based on a user ID and password that a user supplies through an ordinary Web browser, such as Internet Explorer (abbreviated hereafter to Web browser).
Page 17
AX1240S-AP-0202C_R2X After the change: Table 8-2 Operating conditions for Web authentication Type Configuring Specifiable Frame type Fixed VLAN Dynamic VLAN Legacy ports VLAN type Port type Access port native Port VLAN Untagged MAC VLAN Trunk port native Port VLAN Untagged allowed Port VLAN Tagged...
Page 18
AX1240S-AP-0202C_R2X 9. Web Authentication Configuration and Operation 9.4.2 Configuration related to authentication (6) Roaming (permitting authenticated port change communication) configuration [Change] The notes have been corrected as follows: Before the change: Notes: Roaming is available under any of the following conditions: ...
Page 19
AX1240S-AP-0202C_R2X address of the shared printer in the figure: 1234.5600.e001). (config)# interface fastethernet 0/5 (config-if)# switchport mode mac-vlan (config-if)# switchport mac vlan 400 (config-vlan)# exit Specifies MAC VLAN ID 400, to which the excluded terminal belongs, to an authentication port. (config)# mac-address-table static 1234.5600.e001 vlan 400 interface fastethernet Configures the MAC address of a terminal to be excluded from authentication targets and where communication is permitted on port 0/5 of MAC VLAN ID 400 (MAC address of the shared printer in the...
Page 20
AX1240S-AP-0202C_R2X After the change: Table 10-2 Operating conditions of MAC-based authentication Category Configuring Specifiable Frame Fixed VLAN Dynamic Legacy ports VLAN type type VLAN Port type Access port native Port VLAN Untagged MAC VLAN Trunk port native Port VLAN Untagged allowed Port VLAN Tagged...
Page 21
AX1240S-AP-0202C_R2X 11. MAC-based Authentication Configuration and Operation 11.4.2 Settings for authentication processing (4) Setting roaming (allowing communication for moved ports of authenticated terminals) [Change] The notes have been corrected as follows: Before the change: Notes Roaming operates in the following conditions: - Ports for dynamic VLAN mode before and after moving - Post-authentication VLAN before moving has been specified by the configuration command switchport...
AX1240S-AP-0202C_R2X (config-vlan)# exit Sets a MAC address of a terminal excluded from authentication (MAC address of shared server: 1234.5600.e001 in the figure) to MAC VLAN ID 200. (config)# interface fastethernet 0/5 (config-if)# switchport mode mac-vlan (config-if)# switchport mac vlan 200 (config-vlan)# exit Specifies MAC VLAN ID 200 to which the excluded terminal belongs for an authentication port.
Page 23
AX1240S-AP-0202C_R2X <group-name> group RADIUS authentication is used. RADIUS server groups are used. Specify the group name set by the aaa group server radius command. However, you cannot use the following character strings: ・ or a character string beginning with radius radius ・...
Page 24
AX1240S-AP-0202C_R2X (2) schedule-power-control port cool-standby [Change] The impact on communication and the notes have been corrected as follows. [Ver. 2.2.E and later] Before the change: Impact on communication: None Notes: 1. If this command is set, link-up of the Fast Ethernet port takes about 3 seconds. After the change: Impact on communication: Notes:...
AX1240S-AP-0202C_R2X Changes in Operation Command Reference (for Ver. 2.2) (AX1240S-S004-30X) 7. Checking the Software Version and Device Status (1) show environment [Change] Figure 7-6 Operating condition level and temperature [AX1240S] has been corrected as follows: Before the change: Figure 7-6 Operating condition level and temperature [AX1240S] After the change: Figure 7-6 Operating condition level and temperature [AX1240S] (Units: degree Celsius)
Page 28
AX1240S-AP-0202C_R2X IEEE 802.1X (1) show dot1x logging [Change] No. 31 in Table 25-10 List of log messages has been corrected as follows: Before the change: Table 25-10 List of log messages Number Log ID Log type Message text Authentication mode Description Additional information NOTICE...
Page 29
AX1240S-AP-0202C_R2X After the change: Table 26-17 List of log messages Number Log ID Log type Message text Authentication mode Description Additional information NORMAL LOGOUT Force logout ; Authentic method changed (RADIUS <-> Local). Legacy Authentication was canceled because of switching of the authentication methods. Dynamic VLAN This log is collected when any of the following methods is switched: RADIUS Fixed VLAN...
AX1240S-AP-0202C_R2X Changes in Message Log Reference (For Version 2.2) (AX1240S-S005-30X) 2. Switch Failure and Event Information 2.2 Login 2.2.1 Event location = SESSION [Change] Descriptions of No. 4 and 5 in Table 2-5 Switch WARN information when the event location is SESSION have been corrected as follows.
Page 31
AX1240S-AP-0202C_R2X 2.3 Protocol 2.3.1 Event location = STP [Change] The messages in No. 14 and 15 in Table 2-8 Switch WARN information when the event location is STP have been corrected as follows: Before the change: Table 2-8 Switch WARN information when the event location is STP Event Event Ref.
Page 32
AX1240S-AP-0202C_R2X 2.3.9 Event location = DHCPSN [Addition] The following message has been added to No. 15 in Table 2-24 Switch INFO information when the event location is DHCPSN. Table 2-24 Switch INFO information when the event location is DHCPSN Event Event Ref.
AX1240S-AP-0202C_R2X Changes in MIB Reference (For Version 2.2) (AX1240S-S006-30X) 2. Standard MIBs 2.2 interfaces group (MIB-II) 2.2.1 interfaces group [Change] implementation specifications of the group have been corrected as follows. [Ver. 2.2.E ifNumber interfaces and later] implementation specifications of the group have been corrected as follows.
Page 34
AX1240S-AP-0202C_R2X 2.11 dot1dBridge group 2.11.2 dot1dStp group [Change] implementation specifications of the group have been corrected as follows: dot1dStpPortEntry dot1dStp Before the change: Table 2-18 dot1dStp group implementation specifications Object ID Access Implementation specifications Implemented dot1dStpPortEntry [Standard] A list of spanning tree protocol status information for {dot1dStpPortTable 1} each port.
Page 35
Implementation specifications Implemented Maximum number of temperature ax1250sTemperatureStatusNumber INTEGER monitoring points in this chassis {ax1250sChassisEntry 20} For AX1250S series Switches: Fixed value of 3. After the change: Table 3-27 ax1250sChassis group implementation specifications (chassis information) Object identifier Syntax Access Implementation specifications...
Page 36
AX1240S-AP-0202C_R2X 3.14 ax1240sDevice group (system switch chassis information MIB) [AX1240S] 3.14.1 ax1240sChassis group implementation specifications (chassis information) [Change] implementation specifications of the group have ax1240sTemperatureStatusNumber ax1240sChassis been corrected as follows: Before the change: Table 3-34 ax1240sChassis group implementation specifications (chassis information) Object identifier Syntax Access...
Page 37
AX1240S-AP-0202C_R2X 4. Supported MIB Traps 4.1 Supported traps and timing of issuance [Change] No. 19 and 20 in Table 4-1 Supported traps and their timings has been corrected as follows: Before the change: Table 4-1 Supported traps and their timings Trap type Meaning Issued when...