Download Print this page

Bosch GLM Professional 80 Original Instructions Manual page 9

Hide thumbs Also See for GLM Professional 80:

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 1
OBJ_BUCH-3509-001.book Page 9 Thursday, June 28, 2018 9:49 AM
Digital Laser Measure
Indirect Distance Measurement and Vial
Measuring range
Gradient measurement
Measuring range
Measuring accuracy (typical)
Lowest indication unit
General
Operating temperature
Storage temperature
Allowable charging temperature range
Relative air humidity, max.
Laser class
Laser type
Laser beam diameter (at 25 °C) approx.
– at 10 m distance
– at 80 m distance
Setting accuracy of the laser to the housing, approx.
– Vertical
– Horizontal
Automatic switch-off after approx.
– Laser
– Measuring tool (without measurement)
Weight according to EPTA-Procedure 01:2014
Dimensions
Degree of protection
Measuring rail
Article number
Dimensions
Battery
Rated voltage
Capacity
Number of battery cells
Single measurements per battery charge, approx.
A) For measurements from the front measuring tool edge, 100% reflectivity of the target (e.g. a white wall), weak backlighting and 25 °C operating
temperature. In addition, a deviation influence of ±0.05 mm/m must be taken into account.
B) For measurements from the rear measuring-tool edge, 10 – 100 % reflectance of the target, strong backlight and – 10 °C to +50 °C operating tem-
perature. Additionally, a deviation influence of ±0.29 mm/m must be taken into account.
C) For measurements with the rear side of the unit as reference, the max. measuring range is ±60°
D) After calibration in accordance with figure H. Additional pitch error of ±0.01 °/degrees up to 45 °.
E) In the continuous measurement function, the maximum operating temperature is +40 °C.
F) The width of the laser line depends on the surface characteristics and on the ambient conditions.
G) at 25 °C
H) For a new and charged battery without display illumination and tone signal.
The measuring tool can be clearly identified with the serial number 18 on the type plate.
Bosch Power Tools
GLM 80
–60° – +60°
C)
0°–360° (4x90°)
D)F)
0.2°
0.1°
E)
–10 °C...+50 °C
–20 °C...+50 °C
+5 °C...+40 °C
90 %
2
635 nm, <1 mW
F)
6 mm
F)
48 mm
G)
±2 mm/m
G)
±10 mm/m
20 s
5 min
0.14 kg
51 x 111 x 30 mm
IP 54 (dust and splash water
IP 54 (dust and splash water
protected)
Li-Ion
3.7 V
1.25 Ah
1
H)
25000
English | 9
GLM 80+R60
–60° – +60°
C)
0°–360° (4x90°)
D)F)
±0.2°
0.1°
E)
–10 °C...+50 °C
–20 °C...+50 °C
+5 °C...+40 °C
90 %
2
635 nm, <1 mW
F)
6 mm
F)
48 mm
G)
±2 mm/m
G)
±10 mm/m
20 s
5 min
0.14 kg
51 x 111 x 30 mm
protected)
3 601 K79 000
58 x 610 x 30 mm
Li-Ion
3.7 V
1.25 Ah
1
H)
25000
1 609 92A 4GN | (28.6.18)

Advertisement

loading

This manual is also suitable for:

Glm professional 80 plus r60