1. Manuals
  2. Brands
  3. TECHCON SYSTEMS Manuals
  4. Controller
  5. TS550R
  6. User manual

TECHCON SYSTEMS TS550R User Manual

Smart controller for pneumatic valves
Hide thumbs
Table of Contents

Advertisement

Quick Links

Enlarged version
TS550R SMART CONTROLLER
FOR
PNEUMATIC VALVES
User Guide
Copyright © OK International

Advertisement

Table of Contents
loading

Related Manuals for TECHCON SYSTEMS TS550R

Summary of Contents for TECHCON SYSTEMS TS550R

  • Page 1 TS550R SMART CONTROLLER PNEUMATIC VALVES User Guide Copyright © OK International...

  • Page 2: Table Of Contents

    CONTENTS 11. I/O CONFIGURATION AND END OF CYCLE FEEDBACK Page Number During a dispense cycle, an open collector circuit closes and remains closed while Safety ………………………………………………………………… 3 the valve is dispensing. Pin 3 and 4 can be as feedback signal to synchronize with other devices.

  • Page 3: Safety

    9. MAINTENANCE SAFETY The dispenser is designed and built to be relatively maintenance free. To assure 1.1 Intended Use: trouble free operation, please follow below steps: WARNING: Use of this equipment in ways other than those described in this User 1.

  • Page 4: Symbol Definitions

    2. SYMBOL DEFINITIONS 8. TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTION Symbol Description Symbol Description  No power inputs  Check power cord Display does not light up connections  Turn on power Run (Activate) Setup  Supplied pressure  Increase supplied System will not actuate dropped below “Low...

  • Page 5: Specifications

    3. SPECIFICATIONS Wait until the system completes the software update from the USB drive and the first touch-screen calibration is displayed 290mm x 212mm x 98mm Size (11.4” X 8.3” X 3.9”) Weight 3.1 kg (6.8lbs) Input Voltage 24VDC Output Voltage Range 0-24 VDC Rated Power Air Input...

  • Page 6: To Controll Pneumatic Valve

    TO CONTROL PNEUMATIC VALVE “Edit” icon CAUTION: A 5-micron filter (TSD800-6) must be installed with the unit to ensure proper air filtration. TO AIR SOURCE TS570R Proceed to make changes Click “OK” button to save The new parameters will be displayed on the controller 7.

  • Page 7: Login

    5.1.1 Login 6.2 Making Parameters Adjustment from the websever Go back to the webserver site and click on the “Controllers” menu. 1. Touch the Login icon to enter the login screen Click on the active controller link 2. Enter “0000” in Password window The controller screen will be displayed in the webserver as shown below.
  • Page 8 4. Touch the Setup icon to enter the setup screen 18. Go to the setup screen of the controller and touch the “Remote Server” icon 5. Touch the Calibration icon to enter the calibration screen 19. Enter the Server IPv4 address recorded in step #11 into Remote IP address box 20.

  • Page 9: Dispensing

    5.2 DISPENSING 5.2.1 Pressure Adjustment Note: Pressure in Port A and Port B delivers the same output pressure. This pressure is to activate the valve. Make sure the supplied pressure is set at least 70 psi (4.8 bar) 1. Touch the “Pressure A.B” icon to enter the pressure setup screen 2.

  • Page 10: Manual/Purge Dispense Cycle

    9. Type: “set ZONEINFO=C:\iot\timezone.zip” then press the “Enter” button 2. Press the “BAR” icon to change pressure unit to BAR 3. Touch the X icon to save and exit 10. Type: “ipconfig” then press the “Enter” button 5.2.3 Manual/Purge Dispense Cycle Setting: 1.

  • Page 11: Teach Mode Setting

    4. Touch the Check Mark icon to save and exit 5. Press the foot switch to activate the “Timed” dispense cycle. Alternately, touch the run icon on the display to activate the “Timed” dispense cycle. Note: The unit has an “Interrupt” mode feature. In this mode, the “Timed”...
  • Page 12 6. INTERNET of Thing (IoT) 2. Touch the “Run Method” icon 6.1 Setup webserver on the computer 1. Go to Techcon Website (www.techconsystems.com) and download the following files to your computer: The “portal.exe” file The “timezone.zip” file 2. Create a new folder and name “IoT” or any desired name 3.

  • Page 13: Low Pressure Alarm Setting

    If the selected network is an unsecured network (not password protected), touch “Connect” tab to connect 5.3 Low Pressure Alarm Setting Once the unit is successfully connected to the Wi-Fi network, the Note: This controller is equipped with an adjustable “Low Pressure” alarm “Connect”...

  • Page 14: Stored Program In Memory Cell

    5.4 Stored Program in Memory cell 5.7 To Connect to Wi-Fi network. The unit has 50 memory cells to store all dispense parameters. The controller can activate all memory cells in sequence mode. Connect the antenna to the Wi-Fi connector located in the back of the unit 5.4.1 To store dispense parameters Touch the Setup icon to enter the setup screen 1.
  • Page 15 2. Enter number of memory to be run in sequence (ex. 1 to 3) 2. Touch the change “Password” icon 3. Enter the old password, then enter the new password 3. Touch the “Sequence Mode” icon 4. Touch the Check Mark icon to save 5.

  • Page 16: To Run In Continous Sequence Mode

    5.4.3 To run in Continuous Sequence Mode 2. Touch the Counter Reset icon to reset the counter 1. Follow steps 1 to 2 above and enter the waiting time “delay time” between each activation. 2. Touch the “Sequence Mode” icon 3.

Table of Contents