Vlan Subinterfaces: Example - Cisco 6000 Series Configuration Manual
Interface and hardware component
configuration guide for cisconcs 6000 series routers, ios xr release 6.4.x
Hide thumbs
Also See for 6000 Series:
- Configuration manual (68 pages) ,
- Site planning manual (54 pages) ,
- Hardware installation manual (30 pages)
Table of Contents
Advertisement
VLAN Subinterfaces: Example
VLAN Subinterfaces: Example
The following example shows how to create three VLAN subinterfaces at one time:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# interface TenGigE 0/2/0/4.1
RP/0/RP0/CPU0:router(config-subif)# dot1q vlan 10
RP/0/RP0/CPU0:router(config-subif)# ipv4 address 10.0.10.1/24
RP/0/RP0/CPU0:router(config-subif)# interface TenGigE0/2/0/4.2
RP/0/RP0/CPU0:router(config-subif)# dot1q vlan 20
RP/0/RP0/CPU0:router(config-subif)# ipv4 address 10.0.20.1/24
RP/0/RP0/CPU0:router(config-subif)# interface TenGigE0/2/0/4.3
RP/0/RP0/CPU0:router(config-subif)# dot1q vlan 30
RP/0/RP0/CPU0:router(config-subif)# ipv4 address 10.0.30.1/24
RP/0/RP0/CPU0:router(config-subif)# commit
RP/0/RP0/CPU0:router(config-subif)# exit
RP/0/RP0/CPU0:router(config)# exit
RP/0/RP0/CPU0:router# show vlan trunks summary
VLAN trunks: 1,
1 are 802.1Q (Ether).
Sub-interfaces: 3,
3 are up.
802.1Q VLANs: 3,
3 have VLAN Ids.
RP/0/RP0/CPU0:router# show vlan interface
Interface
Te0/6/0/0.1
Te0/6/0/4.1
The following example shows how to create two VLAN subinterfaces on an Ethernet bundle:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# interface bundle-ether 2
RP/0/RP0/CPU0:router(config-if)# ipv4 address 192.168.2.1/24
RP/0/RP0/CPU0:router(config-if)# exit
RP/0/RP0/CPU0:router(config)# interface bundle-ether 2.1
RP/0/RP0/CPU0:router(config-subif)#
RP/0/RP0/CPU0:router(config-subif)# ipv4 address 192.168.100.1/24
RP/0/RP0/CPU0:router(config-subif)# exit
RP/0/RP0/CPU0:router(config)# interface bundle-ether 2.2
RP/0/RP0/CPU0:router(config-subif)# dot1q vlan 20
RP/0/RP0/CPU0:router(config-subif)# ipv4 address 192.168.200.1/24
RP/0/RP0/CPU0:router(config-subif)# exit
RP/0/RP0/CPU0:router(config)# commit
The following example shows how to create a basic dot1Q AC:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# interface GigabitEthernet 0/0/0/0.1
RP/0/RP0/CPU0:router(config-subif)# l2transport
RP/0/RP0/CPU0:router(config-subif)# dot1q vlan 20
RP/0/RP0/CPU0:router(config-subif)# commit
RP/0/RP0/CPU0:router(config-subif)# exit
RP/0/RP0/CPU0:router(config)# exit
Interface and Hardware Component Configuration Guide for Cisco NCS 6000 Series Routers, IOS XR Release 6.4.x
120
-
Encapsulation
802.1Q
802.1Q
Outer 2nd
Service
VLAN
VLAN
1
L3
1
L3
dot1q vlan 10
Configuring 802.1Q VLAN Interfaces
MTU
LineP
State
9604
up
9604
up
Advertisement
Chapters
Table of Contents
