Confer Plastics 6000 Assembly And Installation Manual

Confer 6000_9_04 9/23/04 2:13 PM Page 1
10a.
Please refer to the separate instruction sheet for anti-entrapment barrier installation.
Step 11.
Slide
adjustable
tubes to
position
Place the ladder in the against deck.
desired position on the
deck and slide the
ladder assembly down
Ladder
until the bottom tread
Assembly.
meets the pool liner.
Slide the adjustable
tubes with the mount- Make sure the
ing blocks as needed bottom tread is
to position the ladder flush with the
correctly on the deck. pool liner.
Note: To winterize your ladder, remove it from the pool and drain water from stringers and treads.
Extension Kit for #6000 Ladder - Part #6000-EXT - Raises ladder to reach deck heights from 57" to
approximately 68". Kit includes two extension boots, one additional ladder tread, hardware and instructions.
Order online at www.conferladders.com
SAFETY RULES
• Locate ladder on a solid base
• One person on the ladder at a time
Confer Plastics, Inc. warrants their swimming pool ladders to be free from defects in
• Ladder MUST be installed
workmanship for one year from date of purchase. After the first year the cost to
per manufacturer's instructions
replace a part is as follows:
• DANGER: No Diving
or jumping from ladder
• Face ladder when entering and
leaving pool
• To prevent entrapment or drown-
The defective part should be returned, postpaid, to:
ing, do not swim through, behind or
Confer Plastics, Inc.
97 Witmer Road
around ladder
North Tonawanda
N.Y. 14120 U.S.A.
• Ladder to be used as a swimming
Enclose proof-of-purchase (receipts, etc.) showing date purchased, your name,
pool ladder only
address, and daytime phone number.You will be notified of cost to replace part.
This warranty gives you specific legal rights, and you may also have other rights
which may vary from state to state.
*DANGER: Use a cordless drill for
assembly and installation. Use
OPTIONAL ACCESSORY
extreme caution if using an electric
drill near water. SKIM-IT
75% with skimmer extension that guides debris directly
into your skimmer. Fits most in-ground and above-
ground pool skimmers. Corrosion-resistant plastic Skim-It
installs in seconds without tools.
MADE IN THE U.S.A. by:
4 Printed in U.S.A.
Step 12.
Secure the handrail to the
tubes using four #10 1-1/4"
screws at the pre-marked
locations (two per handrail).
Drill a 1/8" pilot hole through
the handrail ends at the
pre-marked locations into
the stringers and repeat
this step for the adjustable
tubes and mounting blocks.
Secure the handrail using four
#10 1-1/4" screws at the
pre-marked locations
(two per handrail).
LIMITED, PRO-RATED WARRANTY
MODELS #626B / #726 ALL OTHER MODELS:
2nd Year - 40% 2nd Year - 20%
3rd Year - 80% 3rd Year - 40% of current parts
4th Year - 60%
list price
5th Year - 80%
Plus shipping/handling charges
DO NOT RETURN DEFECTIVE PART TO DEALER
SKIMS OFF DEBRIS Cut cleaning time
97 Witmer Road
North Tonawanda, New York 14120
Toll Free U.S. 800-635-3213
716-694-3100 / FAX 716-694-3102
www.conferladders.com
DEALER/INSTALLER: GIVE TO HOMEOWNER
Using a
cordless drill
attach the
mounting
blocks
with eight
ADJUSTABLE HEAVY DUTY INPOOL LADDER
#10 1-1/4"
screws.
Dotted lines
represent pool edge.
As required by ANSI/NSPI - This ladder is equipped with an anti-entrapment barrier to prevent children from swimming behind
or through the rungs of the ladder. It is NOT intended as a substitute for proper adult supervision.
CONFER PLASTICS, INC.
CP-6000 09/04
SAVE THESE INSTRUCTIONS
MODEL 6000
42" TO 56"
ASSEMBLY AND INSTALLATION MANUAL