AMX MXD-430 Quick Start Manual

Overview
The MXD-430 4.3" Modero X Series Wall/Flush Mount Touch Panel (FG5968-15)
features edge-to-edge capacitive touch glass with multi-touch capabilities as well
as advanced technology empowering users to operate AV equipment seamlessly,
while providing the ultimate in audio and video quality. The distinctive appearance
will complement even the most sophisticated meeting facilities and homes.
Left LED Right LED
Sleep
Button
NFC
Sensor
front
MXD-430
FIG. 1
Product Specif ications
MXD-430 SPECIF ICATIONS
Dimensions (HWD) 4 7/8" x 3 1/4" x 2 3/8" (120 mm x 82 mm x 61 mm)
Weight 0.75 lbs (.34 Kg)
Power Consumption • Full-On: 6.5W
• Standby: 4.2W
• Shutdown: 1.9W
• Start-Up Inrush Current: Not applicable due to PoE
standard
External Power Optimal performance requires use of one of the following
Supply Required AMX PoE power supplies (not included):
• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant
(FG423-83)
• NXA-ENET8-2POE, Gigabit PoE Ethernet Switch
(FG2178-63)
Certifications • UL 60950-1
• FCC Part 15 Class B
• C-Tick CISPR 22 Class B
• CE EN 55022, EN 55024 and EN 60950-1
• IEC 60950-1
• IC
• IEC/EN-60950
• RoHS / WEEE compliant
Environmental • Temperature (Operating): 32°F to 104°F (0°C to 40°C)
• Temperature (Storage): 4°F to 140°F (-20°C to 60°C)
• Humidity (Operating): 20% to 85% RH
• Humidity (Storage): 5% to 85% RH
• Power ("Heat") Dissipation:
On: 22.2 BTU/hr
Standby: 14.3 BTU/hr
Included • MXA-USB-C, USB Port Cover Kit (FG5968-18)
Accessories
• MXA-CLK, Modero X/S Series Cleaning Kit (FG5968-16)
• MXD-430 Installation Template
Connector Locations
USB peripherals (mouse, keyboard, etc.) may be connected to either of the two
USB ports on the rear of the device (see FIG. 1). The connectors are accessible
via the Access Slot shown in FIG. 2. and FIG. 3.
Updates to the device's firmware can also made via the USB ports.
USB
Port
rear
MXD-430
4.3" Modero X® Series Wall/Flush Mount Touch Panel
Power via PoE
Power for the MXD-430 is supplied via Power Over Ethernet (PoE), utilizing an
AMX-certified, capacitive touch-compliant PoE injector such as the PS-POE-AF-
TC High Power PoE Injector (FG423-83) or other approved AMX PoE power
source.
The incoming Ethernet cable should be connected to the RJ45 port on the MXD-
430 (FIG. 2).
Front
USB Port
RJ45
Port
BOTTOM VIEW - SHOWING RJ45 AND USB PORTS
FIG. 2
Installing the MXD-430 Into a Wall
The MXD-430 comes with a clear plastic Backbox (designed to attach the panel to
most standard wall materials. This Backbox has two locking tabs (one on each
side) to help lock the Backbox to the wall.
These locking tabs are only extended AFTER the Backbox is inserted into the wall
(FIG. 3)..
Backbox
Locking Tab
Access Slot
MXD-430 BACK BOX (SIDE VIEW)
FIG. 3
• When installing the Backbox, make sure that the assembly is in the correct
position and in the correct place. Once the locking tabs are extended and
locked into place, removing the Backbox may be difficult without having
access to the back of the wall or causing damage to the wall.
• In order to ensure a stable installation of the MXD-430, the thickness of the
wall material must be a minimum of .50 inches (1.27cm) and a maximum of
.875 inches (2.22cm). The mounting surface should also be smooth and flat.
Installing the Backbox
For best results, use the included Installation Template (68-5968-05) to ensure
proper placement.
WARNING: Using the Installation Template to select the f inal placement of the
Backbox is highly recommended. The outside edges of the template are the same
dimensions as the touch panel, which allows you to troubleshoot possible conflicts
with wall edges, doors, and other potential obstacles.
1. Prepare the area by removing any screws or nails from the drywall before
beginning the cutout process.
2. After ensuring proper placement, cut out the mounting surface, using the
(included) Installation Template as a guide.
CAUTION: Making sure the actual cutout opening is slightly smaller than the
provided dimensions is highly recommended. This action provides a margin
for error if the opening needs to be expanded. Too little wall material removed
is always better than too much.
3. Thread the incoming Ethernet cable through the surface opening.
Leave enough slack in the wiring to accommodate any re-positioning of the
panel.
QUICK START GUIDE
Access
Slot
RJ45 Port