Table of Contents
Advertisement
Quick Links
Introduction
The DP CyberSerial 4S PCIe high-speed serial I/O card
provides four additional 9-pin serial ports.
Keyfeatures and Benefits
•
Compliant with PCI Express Base Specification
Revision 1.1
•
PCI Express 1-lane (x1) serial I/O card works with
PCI Express slots with different lane width
•
Installs in any available PCI Express slot and
provides four 9-pin RS232 serial ports via a fan-out
cable
•
Spare enhanced low profile bracket is included to
work in low profile chassis
•
256-byte FIFO buffers dramatically increase data
transmit/receive speed and supports data rates up
to 921 Kbps
System Requirements
•
PCI Express-enabled system with an available PCI
Express slot
•
Windows
64-bit) / Vista (32-/64-bit) / XP (32-/64-bit) / Server
2003 & 2008 (32-/64-bit) / Server 2008 R2 / 2000
•
Windows
04-0995A
DP CyberSerial 4S PCIe
Installation Guide
10(32-/64-bit) / 8.x (32-/64-bit) / 7 (32-/
®
Embedded 8 / 7
®
1
Advertisement
Table of Contents
Related Manuals for SIIG DP CyberSerial 4S PCIe
Summary of Contents for SIIG DP CyberSerial 4S PCIe
-
Page 1: Installation Guide
DP CyberSerial 4S PCIe Installation Guide Introduction The DP CyberSerial 4S PCIe high-speed serial I/O card provides four additional 9-pin serial ports. Keyfeatures and Benefits • Compliant with PCI Express Base Specification Revision 1.1 • PCI Express 1-lane (x1) serial I/O card works with PCI Express slots with different lane width •... -
Page 2: Package Contents
Driver CD • Installation guide Layout Power connector* Jumper settings Fanout cable connector Figure 1: DP CyberSerial 4S PCIe S4 (J4) S2 (J2) Jumper Settings (J1-J4) Short 2-3 = 0 volts Short 1-2 = 5V Short 3-4 = 12V S1 (J1) -
Page 3: Hardware Installation
4-port Fan-out Cable Board connector 9-pin serial Figure 2: 4-port fanout cable Hardware Installation Static Electricity Discharge may permanently damage your system. Discharge any static electricity build up in your body by touching your computer’s case for a few seconds. Avoid any contact with internal parts and handle cards only by their external edges. -
Page 4: Windows Driver Installation
Secure the card with the slot bracket holding screw. Replace the computer cover and reconnect the power cord. Connect the Mini 4-port fan-out cable to the fan-out cable connector on the card. Windows Driver Installation Follow below instructions to install the driver for the DP CyberSerial 4S PCIe : After Hardware Installation, start the computer and insert the driver CD. -
Page 5: To Verify Installation
When the message appears "Do you want to restart ...?", press Y key. After restarting, browse the CD and go to Windows Embedded / Win8 or Win7 / 32-bit or 64-bit folder. Run StnSetup.exe and follow the on-screen steps to install the driver. - Page 6 Blank page...
-
Page 7: Technical Support And Warranty
This warranty is not transferable and is available only to the original purchaser of the product. SIIG will, at our discretion, repair or replace (with an identical product or product having similar features and functionality) the product if defective in materials or workmanship. - Page 8 Fremont, CA 94538-3152, USA Phone: 510-657-8688 DP CyberSerial 4S PCIe is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other names used in this publication are for identification only and may be trademarks of their respective owners.