ORiNG IGS-P9164 Series Quick Installation Manual

SWITCH
I N D U S T R I A L
Q I
uick nstallation
M A N A G E D
Introduction
The IGS-P9164 series is a managed industrial Ethernet switch designed for
power substation and rolling stock applications as it is fully compliant with the
requirements of IEC 61850-3 and IEEE 1613. The series consists of three
models: IGS-P9164GF IGS-P9164FX , , and
16x10/100/1000Base-T(X) ports and differ numbers or types of optical fiber
ports. The devices can be managed centrally via web browsers, TELNET,
Console or other third-party SNMP software as well as ORing's
proprietary Open-Vision management utility. With complete support for
Ethernet redundancy protocols such as O-Ring (recovery time < 30ms over
250 units of connection) and MSTP (RSTP/STP compatible), the devices can
protect your mission-critical applications from network interruptions or
temporary malfunctions with its fast recovery technology. Boasting a wide
o o
operating temperature from -40 C to 85 C, the switch can meet the
demanding requirements of power substations and rolling stock applications.
Package Contents
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
Contents Pictures Number
IGS-P9164GF
or IGS-P9164FX
or IGS-P9164GC
CD
DIN-rail Kit
Wall-mount Kit
Console Cable
QIG
Power Cable
(For HV only)
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Safety & Warnings
Elevated Operating Ambient: If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Mechanical Loading: Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Q I G
IGS-P9164 Series
IGS-P9164 Series
G
uide
Circuit Overloading: Consideration should be given to the connection of the equipment to
the supply circuit and the effect that overloading of the circuits might have on overcurrent
protection and supply wiring. Appropriate consideration of equipment nameplate ratings
should be used when addressing this concern.
IGS-P9164GC, each comes with
Dimension
115.0
G16 G15 Fail
PWR Close
PWR1
G20
G14 G13 PWR2
Fail
Open
G12 G11 Relay
G19
V+/L
G10 G9
V-/N
G8 G7
G18
PWR2
G6 G5
V+/L
G4 G3 V-/N
G17
G2 G1
IGS-P9164GC-HV PWR1
10/100/1000T
G16 G15 TX Fail
PWR Close
G20
(P20) PWR1
RX PWR2
G14 G13 Fail
LNK Open
/ACT
G12 G11 TX Relay
G19
(P19)
RX
G10 G9 V+/L
V-/N
G8 G7 TX
G18
(P18)
PWR2
G6 G5 RX
LNK
/ACT V+/L
G4 G3
TX V-/N
G17
(P17)
RX
G2 G1
10/100/1000T 1000X IGS-P9164GF(X)-HV PWR1
Panel Layouts
X 1
15
G16 G15
G20
G14 G13
1
G12 G11
2
X 1
G19
G10 G9
G8 G7
G18
X 1
G6 G5
G4 G3
G17
G2 G1
X 2
IGS-P9164GC-HV
10/100/1000T
X 1
15
G16 G15 TX
G20
(P20)
RX
G14 G13
4 LNK
/ACT
1
G12 G11 TX
2
X 1
G19
(P19)
RX
G10 G9
G8 G7
TX
X 2
G18
(P18)
RX
G6 G5
LNK
/ACT
G4 G3
TX
G17
(P17)
RX
G2 G1
1000X IGS-P9164GF(X)-HV
10/100/1000T
Rear View
1 1
1907-2-29-IGSP9164-1.0
G16 G15
PWR
PWR1
G20
G14 G13 PWR2
G12 G11
G19
159.0
G10 G9
Relay
COM
G8 G7
Fail Close
Fail Open
G18
G6 G5
V2-
PWR2
V2+
G4 G3
G17 87.0
V1-
G2 G1 PWR1
V1+
IGS-P9164GC-LV
10/100/1000T
G16 G15 TX
PWR
G20
(P20) PWR1
RX PWR2
G14 G13
LNK
/ACT
G12 G11 TX
G19
(P19)
RX
G10 G9
Relay
COM
G8 G7 TX Fail Close
G18 Fail Open
(P18)
G6 G5 RX
LNK
/ACT V2- PWR2
V2+
G4 G3
TX
G17
(P17)
RX V1-
G2 G1 PWR1
V1+
10/100/1000T 1000X IGS-P9164GF(X)-LV
Front View
1. LNK/ACT port for Ethernet ports
2. 10/100/100Base-T(X) Ethernet ports
15
3 Fail G16 G15 3
6 Close 6
PWR PWR 3. Fiber ports (IGS-P9164GF/FX) or
12 7
PWR1 7 7 PWR1
G20
8
PWR2 8 PWR2 Combo ports (IGS-P9164GC)
G14 G13
Fail
9 Open 9
10
10 1 4. LNK status LED for fiber/combo ports
11
4 11 4
Relay G12 G11
2
5. Console port
5
G19
5
V+/L 6. Power LED
G10 G9
13
V-/N
Relay 7. PWR1 LED
12
COM
G8 G7
Fail Close
8. PWR2 LED
Fail Open
G18
PWR2
9. R.M status LED
G6 G5
13
10. Ring status LED
V+/L V2-
PWR2
V2+
G4 G3
V-/N 11. Fault indicator
14 G17
14
V1- 12. Relay output
G2 G1 PWR1
V1+
PWR1 IGS-P9164GC-LV 13. Power 2 module
10/100/1000T
14. Power 1 module
15. Reset button
15
Fail G16 G15 TX
6 Close 6
PWR PWR
3 G20 3
(P20)
PWR1 12 PWR1 7
7 7
PWR2 RX PWR2 8
8
Fail G14 G13
9
9 Open
4 LNK
/ACT 10
10
1
11
11
Relay G12 G11 TX
2
G19
5
(P19)
5 RX
V+/L
G10 G9
V-/N 13
Relay
12
COM
G8 G7
TX Fail Close
Fail Open
G18
(P18)
PWR2
RX
G6 G5
13
LNK V2-
V+/L /ACT
PWR2
V2+
G4 G3
V-/N TX
14
G17
(P17) 14
V1-
RX PWR1
G2 G1
V1+
1000X IGS-P9164GF(X)-LV
PWR1
10/100/1000T
1. Wall-mount screw holes
2. Din-rail screw holes
2
Copyright© 2015 ORing
All rights reserved.
ORing Industrial Networking Corp.
TEL: +886-2-2218-1066 Website: www.oring-networking.com
FAX: +886-2-2218-1014 E-mail: support@oring-networking.com
PRINTED ON RECYCLED PAPER
IEC 61850-3 Industrial Managed Ethernet
Switch
Installation
Use the mounting kits attached with the package and follow the steps below to install the
switch to a rail or to the wall.
DIN-rail Installation
Step 1: Slant the switch and screw the Din-rail kit onto the back of the switch, right in the
middle of the back panel.
Step 2: Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch clicks into
the rail firmly.
R2.5
R3.95
87.9
Wall-mounting
Step 1: Screw the two pieces of wall-mount kits onto both ends of the rear panel of the switch. A
total of six screws are required, as shown below.
Step 2: Use the switch, with wall mount plates attached, as a guide to mark the correct
locations of the four screws.
Step 3: Insert a screw head through the large parts of the keyhole-shaped apertures, and then
slide the switch downwards. Tighten the screw for added stability.
Network Connection
The switch provides standard Ethernet ports. According to the link type, the switch uses
CAT 3, 4, 5, 5e UTP cables to connect to any other network devices (PCs, servers,
switches, routers, or hubs). Please refer to the following table for cable specifications.
Version 1.0
G16 G15 TX Fail
Close
G20 PWR
(P20) PWR1
RX PWR2
G14 G13
Fail
LNK Open
/ACT
G12 G11 TX Relay
G19
(P19)
RX
V+/L
G10 G9
V-/N
G8 G7
TX
G18
(P18) PWR2
G6 G5 RX
LNK
V+/L
/ACT
G4 G3
TX V-/N
G17
(P17)
RX
G2 G1
1000X IGS-P9164GF(X)-HV PWR1
10/100/1000T
Quick Installation Guide