Installation Details; Important Notice - Assa Abloy Highlands HI1000 - HI2000 - HI3000 Installation Instructions Manual

Step 1 of 3: Number of Struts & Strut Size
Model
Highlands HI3000*
Liberty LI3000*
Orleans OL3200 / OL3138
Dilworth Court DC3200 / DL3138
Highlands HI1000 / HI2000
Liberty LI1000 / LI2000
Minimum (1) strut required, on top sec on, for doors with opener
Step 2 of 3: Strut Loca on
Indicates placement
of struts based on number of struts
required and number of sec ons.
5 Sec ons
4 Sec ons Top 1
4
Top 1 Int
Int 3 Int 2
5
Int 2 Int
Bot 4 Bot 3
# Struts # Struts
Strut Detail Example:
16'-0" width x 8'-0" tall - (5) Sec ons - (3) 2" - 20 ga Struts
Step 1: Number of struts - (3) 2" 20 ga.
Step 2: Strut Loca on
Step 3: Strut A achment
Step 3 of 3: Strut A achment
1st Strut
Center S le
A achment
B
Top Sec on
TEK Screws
End S le
A achment
A
Top Sec on
TEK Screws
Width 4 Sec ons
6'-0" - 14'-0" 0 Struts
(1) 2" Strut
14'-2" - 16'-0"
*(1) 2" Struts
16'-2" - 18'-0"
(3) 2" Struts
*(2) 3" Struts
18'-2" - 20'-0"
(3) 2" Struts
16'-2" - 18'-0" (4) 2" Struts (5) 2" Struts
18'-2" - 20'-0" (4) 3" Struts (4) 3" Struts
Top 1
Int
2
Int
5 Sec ons
Int
SEE PAGE 5, STEP 21 FOR
Int

INSTALLATION DETAILS.

Bot 3
C
TEK Screws
D
DAMAGE TO THE GARAGE DOOR DUE TO AN IMPROPERLY
INSTALLED OR ADJUSTED ELECTRIC OPENER IS NOT COVERED BY
5 Sec ons
AMARR'S WARRANTY.
0 Struts
ELECTRIC OPENER ATTACHMENT
*(1) 2" Strut
When installing a garage door opener, the following applies:
(2) 2" Strut
1. The door springs must be in good working order and
*(1) 2" Struts
the door must be balanced (should be able to raise the door 1/2
way and have the door stay in place).
(4) 2" Struts
2. The top sec on of the door MUST include a strut in order to
*(2) 3" Struts
reinforce the opener arm li point (as illustrated in Page 5, Step
21).
(4) 2" Struts
3. Disconnect and/or remove all locks and pull ropes. A emp ng
to use the opener while door is locked will damage your garage
door.
YOUR DOOR MAY REQUIRE ADDITIONAL REINFORCEMENT TO
MEET SPECIFIC WIND & LOAD REQUIREMENTS. ASSA ABLOY
Entrance Systems RECOMMENDS THAT YOU CONTACT YOUR
LOCAL BUILDING OFFICIAL FOR SPECIFIC WIND & LOAD
REQUIREMENTS IN YOUR AREA.
MANY ASSA ABLOY DOORS HAVE ENGINEERING DRAWINGS TO
MEET WIND & LOAD REQUIREMENTS. DOORS MUST BE
ASSEMBLED PRECISELY AS SHOWN IN THE DRAWINGS.
Center S le
A achment
Intermediate &
Bo om Sec on
End S le
A achment
Intermediate &
Bo om Sec on
TEK Screws
Technical data subject to change without notice.

IMPORTANT NOTICE

IMPORTANT NOTICE
B
C
A
D
Page 8.