Page 2
Datalogic reserves the right to change any specification at any time without prior notice. Datalogic is a registered trademark of Datalogic S.p.A. in many countries and the Datalogic logo is a trademark of Datalogic S.p.A. all licensed to Datalogic Scanning, Inc. All other trademarks and trade names referred to herein are property of their respective owners.
UK/US The latest drivers and documentation updates for this product are available on Internet. Log on to: www.scanning.datalogic.com Su Internet sono disponibili le versioni aggiornate di driver e documentazione di questo prodotto. Questo manuale è disponibile anche nella versione italiana.
LYNX™ BT USING LYNX™ BT SERIES READERS ® The Lynx™ BT (Lynx™ Bluetooth ) series reader is a wireless scanner communicating in the 2.4 GHz ISM band and using the Serial Port Profile (SPP). The Lynx™ BT series reader, paired with an OM-1000 BT cradle, builds a Cordless Reading System for the collection, decoding and transmission of decoded data.
DATALOGIC Linear barcode 2D Matrix symbol Relative Size and Location of Aiming System Pattern The field of view indicated by the aiming system will be smaller when the Lynx™ BT is closer to the code and larger when it is farther from the code.
Page 7
LYNX™ BT Charging Power on Charge completed The batteries must be charged at a temperature ranging from 0° to 45 °C (+32° to +113 °F). NOTE For further details about LED functioning refer to the C-1000 and OM-1000 BT Quick Reference Guide. CHANGING THE BATTERIES To change the batteries of your reader, unscrew the battery cover screw, replace the old battery pack with a...
DATALOGIC POWERING THE C-1000/OM-1000 BT Connections should always be made with power off! CAUTION Apply power to C-1000/OM-1000 BT by connecting a power supply unit to the connector on the rear panel of the battery charger/cradle. C-1000/OM-1000 BT is ready to charge Lynx™ BT Series readers with Li-Ion batteries.
Page 9
LYNX™ BT STATUS INDICATORS Lynx™ BT Series Reader LED Functioning Behavior at Power On, blinks briefly, then a beep occurs. Then, it turns off; lights when a wrong read occurs; lights briefly when the aiming system is enabled; Green lights when a code has been read and decoded; blinks during binding with OM-1000 BT (see OM-1000 BT Quick Reference Guide for details);...
Page 10
® the Bluetooth Master device), to recognize the Lynx™ BT reader(s) within radio range. Check that "Datalogic BT Device s/n: " is shown among the discovered devices. Request to open an SPP connection with Lynx™ BT, making sure to disable any required PIN and/or pairing parameters. Lynx™ BT is...
Page 11
LYNX™ BT ® If the PIN of the Bluetooth Master device cannot be disabled, use the PIN "1234". The Lynx™ BT Slave will emit four ascending tones indicating radio connection. NOTE After the Lynx™ BT reader indicates radio connection (see the table on page 5), you can start sending codes.
DATALOGIC LYNX™ BT CONFIGURATION The following procedures must be performed only if using the Lynx™ BT reader with a BT device. If using the reader paired to an OM-1000 BT cradle, you must follow the configuration procedures described in the cradle Quick Reference Guide.
Page 13
LYNX™ BT LYNX™ BT AS MASTER Note: for the hexadecimal character selection of step 4, use the table at the end of this manual. Restore Lynx™ BT default AMHKGPAOFNGNENEIEPANHOGOCK AHHPMBAMDKEOFMHMLJALECHGIK AKCBPJCJGIIJCMCFGPLCMMMNLK AEFBJLBGMHPKMOGNKKNDPDMGGK AAPHBAJIDGHPOJKEFPNCEACBHK AFKFBKNGLGMOMELLGOPCMJFKIK DDDDLDLLLDDLLLLDDDLDDLDLDL Set Lynx™ BT as Master AMHKHNFPFLHOENEIEPANHOGOCK AFNFBEHCLGEOFMHMLJAKFCDFLK APCHDNCJGIIJCMCEGPNKHHFNGK...
LYNX™ BT TECHNICAL FEATURES LYNX™ BT 432 / BT 432E Common Features Electrical Features Power Source Li-Ion battery (2150 mAh) Recharge Time 4 hours max. Operating Autonomy typical 12 h (> 6000 reads) Radio Features ® Bluetooth version 1.2 IEEE 802.15 (class 2) Profile Supported Serial Port Profile Environmental Features...
Page 18
DATALOGIC LYNX™ BT 432 Optical Features Focus distance 115 mm Field of view 21.8° (H) x 16.7° (V) Horizontal field of view at distance (d) 0.4d + 12 in mm Vertical field of view at distance (d) in 0.3d + 9...
Page 19
LYNX™ BT LYNX™ BT 432E Optical Features Focus distance 65 mm Field of view 20° (H) x 15° (V) Horizontal field of view at distance (d) 0.32d + 8.67 in mm Vertical field of view at distance (d) in 0.24d + 6.50 Max Resolution Linear codes - mm (mils) DataMatrix –...
DATALOGIC TROUBLESHOOTING PROBLEM A beep or a LED blink signals an interruption of the radio communication with ® the remote Bluetooth device. SOLUTION • ® It is possible that the distance from the remote Bluetooth device is more than 10 m or that an obstacle interrupted the communication.
24 months from the date of shipment, provided that the product is operated under normal and proper conditions. Datalogic has the faculty to repair or replace the product; these provisions do not prolong the original warranty term.
FCC COMPLIANCE Modifications or changes to this equipment without the expressed written approval of Datalogic could void the authority to use the equipment. This device complies with PART 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference which may cause undesired operation.
Page 23
LYNX™ BT ® BLUETOOTH APPROVAL This product is equipped with the following certified Bluetooth module: Product Name: Panasonic Serial Port Module Bluetooth ID: B01839 Product ID: PAN1440, PAN1450, PAN1540, PAN1550 WEEE COMPLIANCE LASER SAFETY The Lynx™ BT hand-held reader is a Class 1 LED product regarding its Illuminator and a Class 2 laser product regarding its Aiming System.
Page 24
DATALOGIC LA LUCE LASER È DIE LASER- LE RAYON LASER A LUZ LÁSER ES VISIBILE STRAHLUNG IST EST VISIBLE À VISIBLE AL OJO FÜR DAS L'OEIL MU ET IL HUMANO Y ES ALL'OCCHIO UMANO E VIENE MENSCHLICHE EST ÉMIS PAR LA...
Page 25
LYNX™ BT ITALIANO Le seguenti informazioni vengono fornite dietro direttive delle autorità internazionali e si riferiscono all’uso corretto del terminale. NORMATIVE STANDARD PER LA SICUREZZA LASER Questo prodotto risulta conforme alle normative vigenti sulla sicurezza laser alla data di produzione: CDRH 21 CFR 1040 e EN 60825-1. Non si rende mai necessario aprire l’appa-recchio per motivi di installazione, utilizzo o manutenzione.
Page 26
DATALOGIC FRANÇAIS Les informations suivantes sont fournies selon les règles fixées par les autorités internationales et se réfèrent à une correcte utilisation du terminal. NORMES DE SECURITE LASER Ce produit est conforme aux normes de sécurité laser en vigueur à sa date de fabrication: CDRH 21 CFR 1040 et EN 60825-1.
Page 28
Datalogic Scanning, Inc. 959 Terry Street Eugene, OR 97402 dichiara che declares that the déclare que le bescheinigt, daß das Gerät declare que el LYNX BTxxx e tutti i suoi modelli and all its models et tous ses modèles und seine Modelle...