Centurion R5 Quick Setup Manual

CENTURION
THE AUTOMATIC CHOICE
R O T A R Y
Q S G
UICK ETUP UIDE
© Centurion Systems (Pty) Ltd. 1150.D.01.0012_6
UPDATED FOR V2 OPERATORS
This guide is intended for the experienced installer who has done an R3
or R5 installation before, knows all the safety aspects required of a site,
but who needs reminding of the basic steps to follow.
This guide does not replace the manual, but is supplementary to it.
WARNING WARNING
Always ensure that all safety instructions as described in the
Installation Manual are adhered to during the installation
process, and also apply to the completed installation.
TIP!! If in doubt .... refer to the installation manual. (IM)
9
F D A
IT THE RIVE RM
Put the gearbox into manual mode. (IM page 24).
Fit the drive arm to the operator as shown.
A C D A
SSEMBLE LAMP TO RIVE RM
R3 R5
Clamp
Clamp
Drive Arm
Drive Arm
Wedge
Wedge
M12 Washer
M12 Washer
M12 x 65 Bolt
M12 x 65 Bolt
To mount: push clamp onto drive shaft,
tap into place, slide drive arm into clamp,
slip wedge in and fasten with bolt and
washer.
Figure 7 Assemble Clamp to Drive Arm
1
R T & E
EQUIRED OOLS QUIPMENT
Check that you have all the tools required. (IM page 12)
2
S C
ITE ONSIDERATIONS
Check for the safety and suitability of the site by looking at: (IM
page 13)
All safety and local authority requirements.
That the gate is within the operator specifications.
Check that there is enough ground clearance to enable assembly
of the drivearm clamps. (See Figure 4)
3 C R
ABLING EQUIREMENTS
Consider all cabling requirements and routing as in Figure 9. ( IM page
14 )
4 O I
PERATOR NSTALLATION
Estimate the gate swing angle with figure 1.
Then mark the operator's position according to figure 2 or 3.
(IM page 15)
o
0
b
(Gate opening angle)
o
o
120
60
o
o
110
o o o 70
100 90 80
Figure 1 Gate Opening Angle Diagram
7
F G P
ASTEN EARBOX IN OSITION
Fasten the motor onto the pedestal adaptor plate or the wall bracket
using the M8 bolts and washers supplied. (IM page 23)
8 C D A L
UT RIVE RM TO ENGTH
Using the relevant tables below, read off the required drive arm
length.
Then cut the drivearm 50mm longer than D, as shown in Figure 6.
C D L
UT RIVEARM TO ENGTH
Standard Perpendicular
Pedestal Mount Wall Mount
b
Drivearm Drivearm
D
Gate Opening
Angle (Degrees)
60 325
70 370
80 430
90 470
100 490
110 480
120 470
Connecting Arm
Drivearm
Cut drivearm length=D+50mm
Figure 6 Cut Drive Arm Length
S P M
TANDARD EDESTAL OUNT
Pedestal Mount
Installation
H
Gate Bracket
GATE LEAF IN CLOSED POSITION
b
H B C
b
Gate Opening
Angle (Degrees) Gate Bracket
60 0 750 700
70 90 750 700
80 130 750 700
90 220 700 700
100 355 700 650
110 570 600 610
120 605 450 570
Figure 2 Standard Pedestal Mount Installation
W M I
ALL OUNT NSTALLATION
Wall
Bracket
Gate Bracket
C (See Fig. 3)
D
250
300
350
420
480
500
500
Figure 5 Wall/Gate Position
6
R C & S
OUTE ABLES ECURE
Route cables as determined in the cabling plan in Figure 9.
Make sure at least 400mm of cable protrudes above the pedestal or
wall mount bracket. (IM page 22)
P
ERPENDICULAR
C
B B
B E S U R E T O U S E A L O N G
C O N N E C T I N G A R M F O R T H I S
INSTALLATION TYPE.
Ensure that the gate does not exceed the
relevant specifications (IM page 9)
Only recommended values are provided. For
variances, refer to the Installation Manual.
All dimensions shown are indicated in millimetres.
BE SURE TO USE A SHORT CONNECTING ARM FOR
THIS INSTALLATION TYPE.
All recommended values will result in gates with
similar opening times.
Ensure that the gate does not exceed the relevant specifications (IM page 9)
#The minimum value will ensure a clearance of Only recommended values are provided. For variances, refer to the Installation Manual.
30mm if the gate is 50mm thick
All dimensions shown are indicated in millimetres.
All recommended values will result in gates with similar opening times.
H
b
Gate Opening
Angle (Degrees)
60 140
70 180
80 180
90 210
100 305
110 380
120 485
Figure 3 Standard Wall Mount Installation
M
OUNT THE
5
D
ETERMINE
Locate a suitable place for mounting the gate bracket according to
dimension "C" in the tables of Figures 2 or 3.
Determine pedestal or wall mount bracket height relative to gate
bracket as in figure 4 and 5. (IM page 21)
Mount the gate bracket.
P M
EDESTAL OUNT
M
OTOR
300mm sqr
Figure 4 Pedestal/Gate Bracket vertical position
W M
ALL OUNT
Wall Mount
Installation
H C
Gate Bracket
GATE LEAF IN CLOSED POSITION
b
B C
Gate Bracket
180 700
180 700
140 700
140 700
180 700
80 700
80 610
G
ATE BRACKET AND
P H
EDESTAL EIGHT
I
NSTALLATION
C (See Fig. 2)
Gate
Bracket
Cabling
Pedestal
Concrete