Planet FSD-504HP User Manual

1. Package Contents
Check the following contents of your package:
FSD-504HP User's Manual
51V Power Adapter Power Cord
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them
again to repack the product in case there is a need to
return it to us for repair.
- 1 -
2. Product Features
 RJ45 Interface
 Five 10/100Mbps Fast Ethernet ports
 4 ports support 51V DC power to PoE powered
device
 Power over Ethernet
 Complies with IEEE 802.3af/at Power over Ethernet
end-span + mid-span PSE
 Up to 4 IEEE 802.3af/2 IEEE 802.3at devices
powered
 Supports PoE power up to 30 watts for each PoE
port
 60-watt PoE budget
 Hardware DIP switch for "Standard" and "Extend"
mode selection; the "Extend" mode features
30-watt PoE transmit distance of 250m at speed of
10Mbps and VLAN isolation
 Auto detects powered device (PD)
 Circuit protection prevents power interference
between ports
 Remote power feeding up to 100m with standard
mode
- 2 -
 Switching
 Hardware based 10/100Mbps auto-negotiation and
auto MDI/MDI-X
 Flow control for full duplex operation and back
pressure for half duplex operation
 1536bytes packet size support
 Integrates address look-up engine, supporting 1K
absolute MAC addresses
 Automatic address learning and address aging
 Solid DIP switch to isolate ports to prevent
broadcast storm and defend DHCP spoofing
 Hardware
 Desktop palm size
 LED indicators for PoE ready/activity and LINK/ACT
 One DC 51V power jack
- 3 -
3. Switch Front Panel
Figure 3-1 shows the front panel of FSD-504HP.
LNK ACT PoE In-use
PWR
Standard Extend
FSD-504HP
PoE
1 2 3 4 5 Uplink
Figure 3-1: FSD-504HP Front Panel
The front panel of FSD-504HP provides one DIP switch
for "Standard" and "Extend" mode selections. The
detailed descriptions are shown in the following table.
DIP Switch
Function
Mode
This mode makes the FSD-504HP operate
Standard
as a general switch and all ports operate
(default)
at 10/100Mbps auto-negotiation.
 This mode makes the FSD-504HP
operate as a VLAN isolation switch and
port 1 to port 4 will isolate respectively.,
Port 1 to port 4 can only communicate
with port 5 (uplink port).
Extend
 This mode also makes the FSD-504HP
operate at auto–negotiation 10Mbps
speed duplex mode only, but the
delivery distance of PoE power and
network data can reach 250m.
- 4 -
PoE IP Camera
Standard Extend
FSD-504HP
Power
100 meters/328 feet
Extend PoE Mode
PoE IP Camera
Standard Extend
FSD-504HP
Power
250 meters/820 feet
- 5 -
4. LED Indicators
System
LED Color Function
Light: Indicates the Switch has
PWR Green
power.
Per 10/100Mbps Port
LED Color Function
Lights to indicate the port is
PoE Green providing 51V DC in-line
power to remote PoE PD.
Lights to indicate the link through
that port is successfully
established at 10/100Mbps.
LNK/ACT Green
Blinks to indicate that the Switch is
actively sending or receiving
data over that port.
- 6 -
5. Switch Rear Panel
Figure 5-1 shows the rear panel of FSD-504HP.
51V DC
Figure 5-1: FSD-504HP Rear Panel
1. The device is a power-required device,
meaning it will not work till it is pow-
ered. If your networks should be active
all the time, please consider using UPS
(Uninterrupted Power Supply) for your
device. It will prevent you from network
Power
data loss or network downtime.
Notice
2. In some area, installing a surge suppres-
sion device may also help to protect your
FSD-504HP from being damaged by un-
regulated surge or current to the FSD-
504HP or the power adapter.
- 7 -
6. Installing the Switch
This part describes how to install your FSD-504HP and
make connections to it. Please read the following topics
and follow the procedures as presented.
This FSD-504HP does not need software
configuration.
Note
Desktop Installation
To install the FSD-504HP on desktop, simply follow the
following steps:
Step 1: Place the FSD-504HP on desktop near AC
power source for its power adapter.
Step 2: Keep enough ventilation space between the
FSD-504HP and the surrounding objects.
When choosing a location, please keep in
mind the environmental restrictions dis-
cussed in Chapter 7 -- Product Specifica-
Note
tions.
Step 3: Connect your FSD-504HP to network devices.
A. Connect one end of a standard network
cable to the Port-5 of the FSD-504HP that
marks with "Uplink".
- 8 -