Related Manuals for Planet FSD-504PE
Summary of Contents for Planet FSD-504PE
- Page 1 5-Port 10/100Mbps Fast Ethernet Switch with 802.3af splitter built-in FSD-504PE User’s Manual...
-
Page 2: Fcc Warning
All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose. -
Page 3: Table Of Contents
Chapter 1 INTRODUCTION ... 5 Chapter 2 UNPACKING AND SETUP ... 9 Chapter 3 IDENTIFYING EXTERNAL COMPONENTS ... 10 Chapter 4 CONNECTING THE SWITCH ... 12 Chapter 5 TECHNICAL SPECIFICATIONS... 15 APPENDIX A RJ-45 PIN SPECIFICATION ... 16 APPENDIX B SWITCH OPERATION... 18... -
Page 4: About This Guide
ABOUT THIS GUIDE Thank you for purchasing the FSD-504PE, 5-Port 10/100Mbps Fast Ethernet Switch with 802.3af splitter built-in. This device integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities in a highly flexible desktop package and also offers dual power system, DC power and IEEE802.3af in-line power over Ethernet. -
Page 5: Chapter 1 Introduction
For Fast Ethernet networks, a switch is an effective way of eliminating problems of chaining hubs beyond the “two-repeater limit.” A switch can be used to split parts of the network into different... - Page 6 IEEE802.3af uses the protection circuit to detect the support features of remote end-node in a very short time. If the remote-end reply the injector with 802.3af supported signal, the injector will then provide the DC current over the wire to power on the Switch. Otherwise, the Switch will never be turned on.
- Page 7 200Mbps, the Switch can be cascaded from any port and to any number of switches. The Switch is a perfect choice for site planning to upgrade to Fast Ethernet in the Ethernet workgroups can connect to the Switch now, and change adapters and hubs anytime later without needing to change the Switch or reconfigure the network.
-
Page 9: Chapter 2 Unpacking And Setup
Do not place heavy objects on the Switch. Notice: To prevent from device damage, please use the bundled AC Adapter before power on your Switch. And never use any other non-802.3af POE device to port #1 of the Switch. Chapter 2 UNPACKING AND SETUP... -
Page 10: Chapter 3 Identifying External Components
Chapter 3 IDENTIFYING EXTERNAL COMPONENTS This section identifies all the major external components of the Switch. Both the front and rear panels are shown followed by a description of each panel’s feature. Panel The figures below show the panels of the switch. - Page 11 Note: 1. The Switch is a power-required device, it means, the Switch will not work until it is powered. If your networked PCs will need to transmit data all the time, please consider use an UPS (Uninterrupted Power Supply) for your Switch either through POE port or DC 12V. It will prevent you from network data loss.
-
Page 12: Chapter 4 Connecting The Switch
This chapter describes how to connect the Switch to your Fast Ethernet network. PC to Switch A PC can be connected to the Switch via a two-pair Category 3, 4, 5 UTP/STP straight cable. The PC (equipped with a RJ-45 10/100Mbps phone jack) should be connected to any of the 5 numbered port. - Page 13 802.3af in-line power devices like 802.3af POE hub, Ethernet Switches that with 802.3af POE Ethernet port. A Category 5 UTP cable with 4-pair wire is required from POE hub to your FSD-504PE. Once the Switch connect with POE device like PLANET POE-150, 1-Port 802.3af injector or POE hub, the “POE”...
- Page 14 Cat 5/5e UTP/STP cable. When using straight or crossover cable, this is done from the any (MDI/MDIX) port of the Switch (Switch A) to any of the 10Mbps or 100Mbps (MDI-X) port of the other switch (switch B) or other devices.
-
Page 15: Chapter 5 Technical Specifications
Chapter 5 TECHNICAL SPECIFICATIONS Model FSD-504PE Standards IEEE802.3 10Base-T Ethernet IEEE802.3u 100Base-TX Fast Ethernet IEEE802.3af Power over Ethernet Protocol CSMA/CD Data Transfer Rate Ethernet: 10Mbps (half duplex), 20Mbps (full duplex); Fast Ethernet: 100Mbps (half duplex), 200Mbps (full duplex) Topology Star Network Cables EIA/TIA- 568 100-ohm STP (max. -
Page 16: Appendix A Rj-45 Pin Specification
When connecting your FSD-series 10/100Mbps Ethernet Switch to another switch, a bridge or a hub, a straight or crossover cable is necessary. Each port of the Switch supports auto-MDI/MDI-X detection. That means you can directly connect the Switch to any Ethernet devices without making a crossover cable. - Page 17 There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight cable and crossover cable connection: Figure A-1: Straight-Through and Crossover Cable Please make sure your connected cable are with same pin assignment and color as above picture before deploying the cables into your network.
-
Page 18: Appendix B Switch Operation
The information comes from the learning process of Ethernet Switch. Learning When one packet comes in from any port, the Ethernet Switch will record the source address, port no. and the other related information in address table. These information will be used to decide either forwarding or filtering for future packets. - Page 19 Due to the learning function of the Ethernet switch, the source address and corresponding port number of each incoming and outgoing packet are stored in a routing table. This information is subsequently used to filter packets whose destination address is on the same segment as the source address.
-
Page 20: Appendix C Troubleshooting
802.3af standard and well connected to port#1 of the Switch with 4-pair UTP cable within 100 meters. FSD-504PE will detect the signal from 802.3af POE device and response to get the 48VDC power. Connect with non-802.3af complied injector to port#1 could damage the Switch permanently b) Powered from 12VDC: the Switch supports 12VDC AC adapter.