Specifications - Extron electronics CVC 200 User Manual

Cable Connection and Rate Selection
Input connections
Power connector — Plug a standard IEC power cord into this
1
connector to connect the CVC 200 to a 100 to 240VAC, 50 Hz or
60 Hz power source.
Input connectors — Connect a component video input device
2
(HDTV, W-VHS [Y, P
[Y, R-Y, B-Y]) or an RGsB input device to these female BNC
connectors. Use high-resolution cable, such as Extron's BNC-4
mini HR, RG59/HR, or RG6/SHR cable. Connect the input
device as shown in figure 4.
Y, P , P
B R
video
Y/G P
Figure 4 — Input connections
Format rotary switch
Format rotary switch — Use an Extron Tweeker or other small
3
screwdriver to set the Format rotary switch to match the video
input format. The table below shows the switch settings and their
assigned input video formats.
Position
0
1
2
3
4
Format
5
switch
6
7
8
9
A
B-F
3 CVC 200 • Rate Selection
, P ], SMPTE [Y, R-Y, B-Y]), Betacam®
R B
Y, B-Y, R-Y
video
P /R
/B Y/G P /B
R
B B
(B-Y)
RGsB
(SOG)
video
Y/G P /R
P /B
B R
Input
format(s) Standard or rate
Not used
Y, Pb, Pr NTSC/PAL
Y, Pb, Pr HDTV (480p, 576p, 720p, 1035i, 1080i)
Y, Pb, Pr Betacam
Not used
RGsB NTSC/PAL
RGsB Computer rates
Y, Pb, Pr NTSC/PAL
Y, Pb, Pr HDTV (720p)
Y, Pb, Pr HDTV (1080i)
Y, Pb, Pr HDTV (1080p)
Not used
Cable Connection and Rate Selection, cont'd
Output connections
P /R
R
(R-Y)

Specifications

Video
Gain ............................................... Unity
Bandwidth .................................... 55 MHz (-3dB)
Video input
Number/signal type ................... 1 component video (HDTV, W-VHS [Y, P
Connectors .................................... 3 BNC female
Nominal level ............................... 1V p-p for Y of component video
Minimum/maximum levels
Impedance .................................... 75 ohms
Horizontal frequency .................. 15.75 kHz to 45 kHz according to selected mode
Vertical frequency ....................... 60 Hz
Return loss .................................... <-25dB @ 5 MHz
DC offset allowed ........................ ±2V (max.)
CVC 200 • Specifications
Output connectors — Connect an RGBHV or RGBS display to
4
these female BNC connectors. Use high-resolution cable, such as
Extron's BNC-4 or BNC-5 mini HR, RG59/HR, or RG6/SHR
cable. Connect the display as shown in figure 5.
RGBHV
video
R G B
RGBS
video
R G B
Figure 5 — Output connections
SMPTE [Y, R-Y, B-Y], and Betacam [Y, R-Y, B-Y])
or RGsB
0.3V p-p for R-Y and B-Y of component video
0.7V p-p for P
Y ......................................... 0.5V to 1.5V p-p with no offset at unity gain
P P 0.4V to 1.0V p-p with no offset at unity gain
..............................................................
B R
S
H V
S H V
, P ],
R B
, P
B R
4