Wiring; Block Wiring Diagram; Fiber Connections - Siemens Scalance X204-2 Multimode Installation Instructions Manual

WIRING

F2 L2+
F1 M2
FAULT M1
L1+
OUT
P6
P4
IN
P3
OUT
P5
P2
IN
P1
SIEMENS
F2 L2+
F1 M2
FAULT
M1
L1+
OUT
P6
P4
IN
P3
OUT
P5
P2
IN
P1
SIEMENS
Style 7 Block Wiring Diagram

Fiber Connections

Siemens Industry, Inc.
Building Technologies Division
Figure 4 shows the fiber switch module block wiring diagrams for both Style 7 (Class
X) and Style 4 (Class B). Figure 5 shows the wiring for the Fiber Switch connections
in Style 7 and Style 4 (Class B).
All connect All connect All connect All connect All connections are supervised and power ions are supervised and power ions are supervised and power limit ions are supervised and power ions are supervised and power
From P5
on previous
switch
F2 L2+
F1 M2
FAULT
M1
L1+
OUT
P6
P4
IN
P3
OUT
P5
P2
IN
P1
SIEMENS
Figure 4
Style 7 and Style 4 (Class B) Block Wiring of Fiber Switch Module
NOTE: NOTE:
FOR STYLE 4 (CLASS B) FOR STYLE 4 (CLASS B)
OMIT CONNECTION OMIT CONNECTION
BETWEEN FIRST AND BETWEEN FIRST AND
LAST FIBER SWITCH. LAST FIBER SWITCH.
MAXIMUM MAXIMUM
ATTENUATION ATTENUATION
6dB 6dB
PREVIOUS PREVIOUS
SWITCH SWITCH
Figure 5
Fiber Switch Style 7 and Style 4 (Class B) Wiring Connections
Refer to Figure 6 for the wiring of the fiber switch in a VNT-Building configuration.
Figure 7 shows the wiring of the fiber switch in a VNT-FCC (Fire Command Center)
configuration. Refer to Figures 10 and 11 for the wiring of the fiber switch to PAD-3
and PAD-4 and Siemens Building Management System.
Two fiber optic cables are required between each pair of fiber switch modules. Use a
high quality duplex fiber optic cable containing 62.5/125 or 50/125 multimode fiber or
g/125 for single mode fiber. Duplex fiber optic cable has two cables in a single
shield similar to electrical zip cord. Use ST style fiber connectors.
Please contact the fiber Please cont Please cont Please cont Please cont act the fiber act the fiber act the fiber cable manufact act the fiber
the fiber the fiber the fiber the fiber the fiber. . . . . R R R R Refer efer efer efer to S efer to S to S to Scalance X-20 to S calance X-20 calance X-20 calance X-200 Operat calance X-20
for for addit for additional informat addit addit ional information on fiber ional informat ional informat
for for addit ional informat
limit limit limited unless st limit
P5
P6
Style 4 (Class B) Block Wiring Diagram
F2
DO NOT USE DO NOT USE
F1
FAULT
FIBER
TO P5 IN TO P5 IN OUT
NEXT NEXT
SWITCH SWITCH
P6
TO P5 OUT TO P5 OUT
IN
FIBER
FROM P6 IN FROM P6 IN
OUT
P5
FROM P6 OUT FROM P6 OUT
IN
cable manufact cable manufact cable manufacturer cable manufact urer urer urer reg urer reg reg regarding instruct reg
0 Operat 0 Operat 0 Operat 0 Operating Instruct ing Instructions, ing Instruct ing Instruct ing Instruct
ion on fiber ion on fiber opt ion on fiber opt opt optic switc ic switc ic switc ic switches hes hes hes
ion on fiber opt ic switc hes
2
ed unless stat at at at ated otherwise. ed unless st ed unless st ed unless st ed otherwise. ed otherwise. ed otherwise. ed otherwise.
P5 P5
P6 P6
L2+
DO NOT USE DO NOT USE
M2
BLK
POWER POWER
M1
LIMITED LIMITED
L1+
RED
P4
OPTIONAL CONNECTIONS OPTIONAL CONNECTIONS
TO ONE OR MORE: TO ONE OR MORE:
P3
1. ADDITIONAL VNT 1. ADDITIONAL VNT
2. NCC 2. NCC
3. SMOKE CONTROL 3. SMOKE CONTROL
CATEGORY 5 RJ45 CABLE CATEGORY 5 RJ45 CABLE
LESS THAN 20 FT. IN CONDUIT LESS THAN 20 FT. IN CONDUIT
P2
RJ45
P1
CATEGORY 5 RJ45 CABLE CATEGORY 5 RJ45 CABLE
LESS THAN 20 FT. IN CONDUIT LESS THAN 20 FT. IN CONDUIT
SIEMENS
arding instructions for arding instruct arding instruct arding instruct ions for ions for ions for t t t t terminat ions for erminat erminat erminating erminat
ions, ions, ions, C790 ions, C790 C790 C790 C7900 0 0 0 0 0-G897 0-G897 0-G897 0-G897 0-G8976-C284-05, 6-C284-05, 6-C284-05, 6-C284-05, 6-C284-05,
P/N 315-050537-3
To P6
on next
switch
ing ing ing ing