Download  Print this page

Circuit Adjustments; P & P Sub Contrast Adjustment (video) (scon); P & P Sub Contrast Adjustment (rf) (scon); P & P Sub-hue And Sub-color Adjustment (shue, Scol) - Sony KP-HR432K90 Service Manual

Hide thumbs

Advertisement

4-1. P & P SUB CONTRAST ADJUSTMENT
(VIDEO) (SCON)
1. Receive the signal.
TV terminal (sub)
: Color-bar (white-75%, No
VIDEO terminal (main) : Color-bar (white-75%, No
2. VIDEO MODE
: Pro
PICTURE
: maximum
COLOR
: minimum
RGB Signal
: off
3. Set to P & P mode, and set to service mode.
4. Connect an oscilloscope between the check point and ground.
Check points
: CN5 pin 6 (G)
(A Board)
5. Select " 2103-1-02 "(Main scon), and adjust so that the wave-
form level of VWB is 2.00 (1.67) ± 0.04Vp-p.
6. Select " 2103-2-02 "(Sub scon), and adjust so that the wave-
form level of VWB is 2.00 (1.67) ± 0.04Vp-p.
7. Write the data into memory.
MUTING n
ENTER
VR1-VR2=VR
VR2
Fig. 4-1
4-2. P & P SUB CONTRAST ADJUSTMENT (RF)
(SCON)
1. Receive the signal.
TV terminal (main)
: Color-bar (white-75%, No
VIDEO terminal (sub) : Color-bar (white-75%, No
2. VIDEO MODE
: Pro
PICTURE
: maximum
COLOR
: minimum
RGB Signal
: off
3. Set to P & P mode, and set to service mode.
4. Connect an oscilloscope between the check point and ground.
Check points
: CN5 pin 6 (G)
(A Board)
5. Select " 2103-1-02 "(Main scon), and adjust so that the wave-
form level of VWB is 2.00 (1.67) ± 0.04Vp-p.
6. Select " 2103-2-02 "(Sub scon), and adjust so that the wave-
form level of VWB is 2.00 (1.67) ± 0.04Vp-p.
7. Write the data into memory.
MUTING n
ENTER
VR1-VR2=VR
VR2
Fig. 4-2
SECTION 4

CIRCUIT ADJUSTMENTS

( ):HW572K90
setup)
setup)
White
VR1
Pedestal
( ):HW572K90
setup)
setup)
White
VR1
Pedestal
KP-HR432K90/HR532K90/HR532N90/HW572K90
RM-Y909K
4-3. P & P SUB-HUE AND SUB-COLOR ADJUSTMENT
(SHUE, SCOL)
1. Receive the signal.
TV terminal (sub)
VIDEO terminal (main) : Color-bar (white-75%, No
2. VIDEO MODE
PICTURE
COLOR
RGB Signal
3. Set to P & P mode, set to service mode.
4. Connect an oscilloscope between pin 7 (B) of CN5 (A board)
connecter and ground.
5. Select " 2103-1-03 SCOL, -04 SHUE "(Main), and adjust
< =
them to have VB1 VB4 and VB2 VB3 in the waveform
levels.
6. Select " 2103-2-03 SCOL, -04 SHUE "(Sub), and adjust them
< =
to have VB1 VB4 and VB2 VB3 in the waveform levels.
7. Write the data into memory.
MUTING n
ENTER
4-4. P & P SUB-HUE AND SUB-COLOR ADJUSTMENT
(SHUE, SCOL)
1. Receive the signal.
TV terminal (main)
VIDEO terminal (sub) : Color-bar (white-75%, No
2. VIDEO MODE
PICTURE
COLOR
RGB Signal
3. Set to P & P mode, set to service mode.
4. Connect an oscilloscope between pin 7 (B) of CN5 (A board)
connecter and ground.
5. Select " 2103-1-03 SCOL, -04 SHUE "(Main), and adjust
< =
them to have VB1 VB4 and VB2 VB3 in the waveform
levels.
6. Select " 2103-2-03 SCOL, -04 SHUE "(Sub), and adjust them
< =
to have VB1 VB4 and VB2 VB3 in the waveform levels.
7. Write the data into memory.
MUTING n
ENTER
– 33 –
RM-Y909K
RM-Y908
: Color-bar (white-75%, No
setup)
setup)
: Pro
: maximum
: center
: on
< =
< =
VB1
VB2
VB3
VB4
Fig. 4-3
: Color-bar (white-75%, No
setup)
setup)
: Pro
: maximum
: center
: on
< =
< =
VB1
VB2
VB3
VB4
Fig. 4-4
RM-Y909K

Advertisement

Table of Contents

   Related Manuals for Sony KP-HR432K90

This manual is also suitable for:

Kp-hr532k90Rm-y908Kp-hw572k90Kp-hr532n90Rm-y909k

Comments to this Manuals

Symbols: 0
Latest comments: