Table of Contents
Related Manuals for Renesas User System Interface Board HS1664ECH61H
Summary of Contents for Renesas User System Interface Board HS1664ECH61H
- Page 1 REJ10J1395-0100 H8SX/1663 Group E6000H FP-144L User System Interface Board HS1664ECH61H User’s Manual Renesas Microcomputer Development Environment System H8SX Family / H8SX/1600 Series HS1664ECH61HE Rev.1.00 Revision Date: Jun. 28, 2006...
- Page 3 (iii) prevention against any malfunction or mishap. 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp.
-
Page 5: Important Information
Renesas) pursues a policy of continuing improvement in design, performance, functions, and safety of the user system interface board. Renesas reserves the right to change, wholly or partially, the specifications, design, user's manual, and other documentation at any time without notice. -
Page 6: Limited Warranty
User system interface boards are wearing parts which Renesas will not repair or replace if damaged and/or worn through use. The foregoing shall constitute the sole remedy for any breach of Renesas’... - Page 7 This user's manual and user system interface board are copyrighted and all rights are reserved by Renesas. No part of this user's manual, all or part, may be reproduced or duplicated in any form, in hard-copy or machine-readable form, by any means available without Renesas’ prior written consent.
-
Page 8: Read First
• READ this user's manual before using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. DEFINITION OF SIGNAL WORDS This is the safety alert symbol. - Page 9 Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance.
- Page 10 Preface The HS1664ECH61H is a user system interface board that connects a user system for the H8SX/1663, H8SX/1664 FP-144L package to the H8SX/1650 E6000H emulator (HS1650EPH60H). Emulation of the H8SX/1663 group is only possible when this user system interface board is connected to the HS1650EPH60H.
-
Page 11: Table Of Contents
Section 1 Configuration...1 Section 2 Connection Procedures ...3 Connecting the User System Interface Board to the User System ... 3 2.1.1 Installing the IC Socket... 4 2.1.2 Soldering the IC Socket ... 5 2.1.3 Inserting the IC Socket Connector... 5 2.1.4 Fastening the IC Socket Connector... -
Page 12: Section 1 Configuration
Figure 1 and table 1 show the configuration and components of the user system interface board for the FP-144L package. Please make sure you have all of these components after you have unpacked the box. Screws (M2 × 6 mm) Socket cover Figure 1 User System Interface Board for the H8SX/1663, H8SX/1664 FP-144L Package Section 1 Configuration... - Page 13 Use an NQPACK144SD socket (manufactured by Tokyo Eletech Corporation) as the FP-144L-packaged IC socket on the user system. Table 1 HS1664ECH61H Components No. Component User system interface board IC socket Socket cover Screw (M2 x 10 mm) Screw (M2 x 6 mm) Spacers (2.6MP x 25 mm) 2 Spacers (2.6MQ x 13 mm) 4 Screwdriver...
-
Page 14: Section 2 Connection Procedures
Section 2 Connection Procedures Connecting the User System Interface Board to the User System Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed. Before connecting the two, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. -
Page 15: Installing The Ic Socket
To connect the board to the user system, follow the instructions below. 2.1.1 Installing the IC Socket After checking the location of pin 1 on the IC socket fasten it to the user system before soldering. After confirming the location of pin 1 on the IC socket, apply epoxy resin adhesive to the end of the four projections at the bottom of the IC socket, and fasten it to the user system. -
Page 16: Soldering The Ic Socket
2.1.2 Soldering the IC Socket After fastening, solder the IC socket for an FP-144L package to the user system. Be sure to completely solder the leads so that the solder gently covers the leads and forms solder fillets. (Use slightly more solder than with the MCU.) 2.1.3 Inserting the IC Socket Connector Check the location of pin 1 before inserting. -
Page 17: Fastening The Ic Socket Connector
2.1.4 Fastening the IC Socket Connector 1. Use the screwdriver provided for tightening screws. 2. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. - Page 18 User system Figure 3 Connecting the User System Interface Board to the User System Screws (M2 × 10 mm) (for fastening the board) User system interface board Pin 1 IC socket (NQPACK144SD manufactured by Tokyo Eletech Corporation)
-
Page 19: Exchanging The Spacers Of The Evaluation Chip Board
Exchanging the Spacers of the Evaluation Chip Board After connecting the user system interface board to the user system, be careful not to apply load to the user system. Exchange the spacers (2.6MP × 10 mm) of the evaluation chip board with the spacers (2.6MP × 25 mm) provided with the user system interface board and adjust the height. -
Page 20: Connecting The User System Interface Board To The Evaluation Chip Board
Connecting the User System Interface Board to the Evaluation Chip Board Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. - Page 21 Figure 5 Connecting the User System Interface Board to the Evaluation Chip Board Evaluation chip board User system interface board Connector No. Evaluation Board Chip Board Connector No. Connector No. UCN1 UCN1 UCN2 UCN2...
-
Page 22: Recommended Dimensions For The User System Mounting Pad (Footprint)
Recommended Dimensions for the User System Mounting Pad (Footprint) Figure 6 shows the recommended dimensions for the mounting pad (footprint) for the user system with the IC socket for an FP-144L package (NQPACK144SD: manufactured by Tokyo Eletech Corporation). Note that the dimensions in figure 6 are somewhat different from those of the mounting pad for the system with the actual MCU. -
Page 23: Dimensions Of The Evaluation Chip Board And The User System Interface Board
Dimensions of the Evaluation Chip Board and the User System Interface Board The dimensions of the evaluation chip board and the user system interface board are shown in figure 7. Figure 7 Dimensions of the Evaluation Chip Board and the User System Interface Board 140.0 Evaluation chip board 118.5... -
Page 24: Resulting Dimensions After Connecting The User System Interface Board
Resulting Dimensions after Connecting the User System Interface Board The dimensions of the assembly after the user system interface board has been connected to the user system are shown in figure 8. Spacer (φ5.8) Figure 8 Dimensions of the Assembly after Connection of the User System Interface Board Evaluation chip board IC socket (NQPACK144SD... -
Page 25: Using The Emulator Without Connecting User System
Using the Emulator without Connecting User System Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed. Before connecting the two, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. - Page 26 USER ON USER OFF Figure 9 SW1 Jumper Socket Figure 10 Attaching Spacers Spacer (2.6MQ x 13 mm)
-
Page 27: Section 3 User System Interface Circuits
Section 3 User System Interface Circuits The following user interface circuits are required for the emulator when the user system interface board is in use. Sub-MCU MD_CLK PM0-PM4 VBUS DrVcc USD- USD+ DrVss Figure 11 User System Interface Circuit (1) Note: The power-supply circuit shown above is turned on/off by the setting of the SW1 jumper pin on HS1664ECH61H. - Page 28 Figure 12 User System Interface Circuit (2) SN74CB3Q3306A Sub-MCU SN74CB3Q3306A Figure 13 User System Interface Circuit (3) SN74CB3Q3306A SN74CB3Q3306A User system User system...
- Page 29 User system EPM7128 UHC14 VHC244 47 kΩ _RES _RES EPM7128 Figure 14 User System Interface Circuit (4)
-
Page 30: Section 4 Verifying Operation
Section 4 Verifying Operation 1. Turn on the emulator according to the procedures described in the H8SX/1650 E6000H Emulator User's Manual (HS1650EPH60HE). 2. Verify the user system interface cable connections by checking the pin states with the EXMONITOR_DISPLAY command (emulator command) and checking the bus states with the MEMORY_FILL command (emulator command). - Page 31 ⎯ To use the crystal oscillator mounted on the evaluation chip board Install the crystal oscillator into the crystal oscillator terminals on the evaluation chip board. Crystal oscillator terminals Figure 16 Installing the Clock Oscillator Enlarged view Crystal oscillator Evaluation chip board...
-
Page 32: Section 5 Points For Caution
Section 5 Points for Caution 1. Before connecting any parts or cables, make sure that the pins at the pin 1 position on both sides are correctly aligned. 2. Do not apply excessive force to the user system interface board while it is connected to the user system. - Page 33 8. When you use the emulator without connecting it to the user system, ensure that the SW1 jumper pin is inserted to [USER-OFF]. While no pin or SW1 jumper pin is inserted to [USER-OFF], the emulator supplies 3.3-V power to DrVCC, which is the power supply exclusively used for USB.
-
Page 34: Section 6 Restrictions
There are the following restrictions on emulation of the H8SX/1663 group when the user system interface board is connected to the emulator. 1. The USB clock frequency is fixed to 48 MHz regardless of the EXTAL input. 2. P14 cannot be used as a port if the serial output function has already been selected. The port pin state cannot be read from the port register. - Page 35 HS1664ECH61H User's Manual Publication Date: Rev.1.00, June 28, 2006 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Customer Support Department Global Strategic Communication Div. Renesas Solutions Corp. © 2006. Renesas Technology Corp., All rights reserved. Printed in Japan.
- Page 36 Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan http://www.renesas.com RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.
- Page 37 H8SX/1663 Group E6000H FP-144L User System Interface Board HS1664ECH61H User’s Manual...