Page 1
IMPORTANT File in your maintenance records Renaissance Series 1009 Emergency Care Stretcher 1509 PACU Stretcher For stretchers with serial numbers of 9711030529 and above MAINTENANCE MANUAL For Parts or Technical Assistance 1–800–327–0770...
Introduction INTRODUCTION This manual is designed to assist you with the maintenance of the 1009 Emergency Care Stretcher and the 1509 PACU Bed. Read it thoroughly before using the equipment or beginning any maintenance on it. SPECIFICATIONS 1009 1509 Maximum Weight Capacity...
Preventative Maintenance CHECKLIST (PERFORM A MINIMUM OF TWICE A YEAR) All fasteners secure (reference all assembly prints) Siderails move and latch properly (page 5) Engage brake pedal and push on the stretcher to ensure all casters lock securely (page 15) Steer function working properly All casters secure and swivel properly Body restraints working properly...
If these types of products are used to clean Stryker patient handling equipment, measures must be taken to insure the stretchers are rinsed with clean water and thoroughly dried following cleaning. Failure to properly rinse and dry the stretchers will leave a cor- rosive residue on the surface of the stretcher, possibly causing premature corrosion of critical components.
Service Information PNEUMATIC FOWLER ADJUSTMENT Required Tools: 5/32” Hex Allen Wrench 1/2” Open End Wrench Adjustment Procedure: 1. Refer to drawings 1210–31–120 or 1710–31–120 (Pneumatic Fowler Assembly, page 45 or page 47) for parts reference. 2. For easier access, move Fowler to 75 degrees or higher. 3.
Page 9
Service Information PEDAL LINKAGE ADJUSTMENT – DUAL SIDE CONTROL BASE Required Tools: 3/32 Hex Allen Wrench 7/16 Open End Wrench 1/2 Open End Wrench (2) Wooden blocks (10 – 12 inches in length) Adjustment Procedure: 1. Pump the litter up to full height. 2.
Page 10
Service Information PEDAL LINKAGE ADJUSTMENT – DUAL END CONTROL BASE Required Tools: 7/16 Open End Wrench 1/2 Open End Wrench (2) Wooden Blocks (10 – 12 inches in length) Adjustment Procedure: 1. Pump the litter up to full height. 2. Lift the base hood, separating the hood from the base frame. Using the wooden blocks, support the base hood.
Service Information CASTER ASSEMBLY REPLACEMENT* Required Tools: 1/8 Roll Pin Punch Drill with 1/8 inch Drill Bit Flat Punch (any size larger than 1/8) Hammer Needle Nose Pliers Floor Jack 3/4 Inch Wrench (2) Wooden Blocks (10 – 12 inches in length) 1 Inch Wrench Torque Wrench (w/ Ft.
Page 12
Service Information CASTER MAINTENANCE Required Tools: 5/8” Wrench 11/16” Wrench Maintenance Procedure: 1. Remove the plastic caster cover (see page 9). 2. Using the 5/8” wrench and the 11/16” wrench, remove the centerlock nut (item A) from the through bolt (item B) for the caster wheel.
Service Information CASTER COVER INSTALLATION AND REMOVAL Looking through the larger of the two side cut–outs, align cover with axle nut or bolt head, as shown. Double Prongs Push down on the opposite side of the cover until single prong engages with caster horn. Single Prong Top View (Cut–Away) Properly Attached...
Page 15
Jack will not pump up and the jack actuator rod Remove excess air (vacuum) in system (see p. may or may not move. 12). Contact Stryker technical service at 1–800–327–0770 for further assistance.
Service Information BRAKE RING REPLACEMENT Brake Ring Part Number 715–1–61 Required Tools: Phillips Screwdriver String or Bungee Cord Floor Jack, Small Crate (or equiv.) Large Standard Screwdriver 3/32” Allen Wrench 11/16” Socket & Ratchet 5/8” Wrench Needle–Nose Pliers (2) 7/16” Wrenches Procedure: 7.
6. The hydraulic fluid should be visible at the bottom of the fill hole. If it is not, add Mobil Aero HFA hydraulic fluid (Stryker part number 2020–70–475) until the fluid is visible at the bottom of the fill hole. Replace the fill plug.
Service Information HYDRAULIC CHECK VALVE REPLACEMENT Required Tools: 3/8 Open End Wrench Stiff Wire (with bent, pointed end) Small Needle Nose Pliers 3/4 Open End Wrench Torque Wrench (with Ft. Lbs. adjust.) 7/32 Hex Allen Wrench 1/2 Inch Diameter Rod Replacement of Valve #1 WARNING To avoid personal injury or damage to the stretcher, remove the litter and the base hood before beginning...
Page 19
Service Information HYDRAULIC CHECK VALVE REPLACEMENT (CONT’D) Replacement of Valve #2 WARNING To avoid personal injury or damage to the stretcher, remove the litter and the base hood before beginning service on the jacks. Lower the jack rod completely to relieve the pressure on the pump piston side of the jack.
Page 20
Service Information BRAKE ADJUSTMENT Required Tools: 3/32” Hex Allen Wrench Pry Bar Thread ”Locktite” BASE LUBRICATION Do not grease area shown. 1. Lubricate brake adjuster rod around area shown with MPG–2 grease or equivalent.
Page 22
Side Control Base Assembly (with Brakes) Item Part No. Part Name Qty. 715–1–245 Base Weldment Assembly 38–211 Spring 715–1–158 Caster Nut 715–1–61 Caster Brake Assembly (Page 18) Brake Adjuster Assembly 715–1–231 Brake/Steering Rod Assembly 1000–10–62 Steering Lock Linkage Bar (Page 19) Brake Cam Assembly 715–1–94 Compression Spring...
715–1–213 Brake Cam Assembly Item Part No. Part Name Qty. 715–1–221 Brake Cam 16–59 Fiberlock Nut 8–21 Soc. Hd. Cap Screw 715–1–173 Brake Connecting Link...
Page 25
Assembly part number 716–1–251 Note: Parts and assemblies drawn with broken lines are part of optional accessories.
Page 26
End Control Base Assembly (with Wheels and Brakes) Item Part No. Part Name Qty. 716–1–246 Base Weldment Ass’y 8–17 Soc. Hd. Shoulder Bolt 715–1–158 Caster Nut 715–1–61 Caster Brake Assembly (Page 18) Brake Adjuster Assembly 1210–1–345 Brake/Steer Pedal, Ft. End 1210–1–346 Brake/Steer Pedal, Hd.
Page 27
End Control Brake Pedal Assembly, Head Assembly part number 716–1–269 Item Part No. Part Name Qty. 716–1–275 Brake Pedal 716–1–267 Brake Rod Ass’y, Welded End Control Brake Pedal Assembly, Foot Assembly part number 716–1–263 Item Part No. Part Name Qty. 716–1–275 Brake Pedal 716–1–262...
Page 28
Caster Assembly with Steerlock Assembly part number 715–2–21 Item Part No. Part Name Qty. 700–10–50 Steer Lock Caster Weldment 715–2–25 Caster Wheel 16–60 Hex Nut 3–99 Hex Bolt 715–3–96 Hex Bolt 1000–59–10 Latch Assembly 11–310 Flat Washer...
Page 29
Caster and Caster Cover Replacement Kits Item Part No. Part Name Qty. 715–2–20 Caster Assembly 715–1–266 Caster Cover, Left 715–1–265 Caster Cover, Right P/N 715–259–400 – Kit to replace 4 standard caster assemblies with necessary hardware – no caster covers. P/N 715–269–400 –...
715–270–400 Jack Assembly Item Part No. Part Name Qty. Item Part No. Part Name Qty. 45–904 O–Ring 388–1–38 Plug 715–1–340 Cap Assembly 715–1–322 Reservoir 390–1–243 Gasket 390–1–244 Gasket 715–1–323 Actuator Cylinder 390–1–238 Gasket, Actuator 715–1–325 Actuator (Page 27) Jack Base Assembly 45–14 O–Ring 390–2–139...
Page 34
Jack Base Assembly Assembly part number 715–370–5 (reference only) Item Part No. Part Name Qty. Item Part No. Part Name Qty. 14–50 Bearing Retainer 715–1–327 Cylinder Wear Ring 38–311 Compression Spring 715–1–328 Piston Wear Ring 45–6 O–Ring 715–1–329 Pump Seal 45–110 O–Ring 715–1–341...
Page 35
Side Control Base Assembly (with Jacks) Assembly part number 715–1–260...
Page 36
Side Control Base Assembly (with Jacks) Item Part No. Part Name Qty. 29–7 Dual Lock (Page 26) Jack Assembly 11–262 Flat Washer 3–62 Hex Hd. Cap Screw 11–3 Flat Washer 16–36 Nylock Hex Nut 715–1–192 Jack Support 3–85 Hex Hd. Cap Screw 715–1–193 Jack Support Clamp 13–38...
Page 37
Pedal Base Assembly, Pump Assembly part number 715–1–108 Item Part No. Part Name Qty. 715–1–83 Pedal Ass’y Weldm’t, Pump 715–1–126 Side Control Pedal Pad 81–44 Bearing, Bronze NOTE Apply plastic adhesive to the mating surfaces of item B prior to assembly.
Page 38
Pedal Base Assembly, Head End, Right Assembly part number 715–1–110 Item Part No. Part Name Qty. 715–1–97 Release Pedal Weldment 721–40–25 Pedal Pedal Base Assembly, Head End, Left Assembly part number 715–1–109 Item Part No. Part Name Qty. 715–1–98 Release Ped. Wldmt., Hd. Lt. 721–40–25 Pedal NOTE...
Page 39
Side Control Base Assembly (with Jacks) 31.1...
Page 40
Side Control Base Assembly (with Jacks) Item Part No. Part Name Qty. 3–47 Hex Head Cap Screw 3–62 Hex Hd. Cap Screw 3–85 Hex Hd. Cap Screw 4–146 Soc. Hd. Cap Screw 11–3 Washer 11–4 Flat Washer 11–262 Flat Washer 13–38 Ext.
Page 41
Side Release Pedal Assembly Assembly part number 1210–1–150 Item Part No. Part Name Qty. 715–1–126 Side Control Pedal Pad 1210–1–152 Side Release Pedal Weldment 1 31.3...
Page 43
Assembly part number 716–1–270 FOOT END HEAD END...
Page 44
End Control Base Assembly (with Jacks) Item Part No. Part Name Qty. 3–4 Hex Head Cap Screw 3–62 Hex Hd. Cap Screw 3–85 Hex Hd. Cap Screw 11–3 Washer 11–13 Flat Washer 11–262 Flat Washer 13–38 Ext. Tooth Lock Washer 14–2 Washer 14–3...
Page 45
End Control Pump Pedal Assembly, Head Assembly part number 716–1–292 Item Part No. Part Name Qty. 716–1–285 Pump Pivot, Head End 26–12 Roll Pin 716–1–290 Pump Ped. Wldmt., Head 721–40–25 Pedal End Control Pump Pedal Assembly, Foot Assembly part number 716–1–288 Item Part No.
End Control Stretcher Base Labeling Assembly Item Part No. Part Name Qty. 946–1–60 Stryker Logo Label 1001–1–135 Hood Assembly 715–1–134 Bellows 29–9 Dual Lock (not shown) 25–77 Rivet 1009–1–17 Specification Label 1509–1–17 Specification Label 715–1–176 Oxygen Bottle Holder 11–16 Washer 29–7...
Page 47
End Control Graphics Reference below for dept. label part numbers Color Item A Control Label, Item B Control Label, Item C Stripe Label Litter Bumper Strip Head Foot 1010–800–11 1010–800–12 1010–800–13 1010–700–15 PURPLE 1010–800–21 1010–800–22 1010–800–23 1010–700–25 GREEN 1010–800–31 1010–800–32 1010–800–33 1010–700–35 GRAY...
Page 48
Side Control Graphics Reference previous page for dept. label part numbers. Color Item A Control Label, Right Item B Control Label, Left Litter Bumper Strip 1001–700–111 1001–700–112 1010–700–15 PURPLE 1001–700–121 1001–700–122 1010–700–25 GREEN 1001–700–131 1001–700–132 1010–700–35 GRAY 1001–700–141 1001–700–142 1010–700–45 TEAL 1001–700–151 1001–700–152...
Litter Assembly Assembly part number 1009–30–10 Item Part No. Part Name Qty. Item Part No. Part Name Qty. 11–360 Plastic Spacer 1001–1–37 Jack Supt. Tube, Hd. 3–76 Hex Hd. Cap Screw 1001–1–41 Hole Plug 3–78 Hex Hd. Cap Screw 1001–201–30 Trend. Support 4–201...
Siderail to Litter Assembly, Fold–to Head Assembly part number 1009–20–10 Item Part No. Part Name Qty. 4–135 But. Hd, Cap Screw 4–136 But. Hd. Cap Screw 11–2 Flat Washer 16–28 Nylock Nut 21–104 Set Screw 37–74 Hole Plug 38–220 Compression Spring 721–26–66...
Siderail to Litter Assembly, Fold to Foot Assembly part number 1009–21–10 Item Part No. Part Name Qty. 4–135 But. Hd, Cap Screw 4–136 But. Hd. Cap Screw 11–2 Flat Washer 16–28 Nylock Nut 21–104 Set Screw 37–74 Hole Plug 38–220 Compression Spring 721–26–66...
Page 55
Siderail Assembly, Right & Left, Fold to Foot Assembly part numbers 721–26–96 (Right) 721–26–97 (Left) (Right Side Shown) Item Part No. Part Name Qty. 1010–26–15 Top Rail 1010–26–83 Upright 1010–26–84 Upright, Bent 1010–26–82 Spacer 25–106 Semi–Tubular Rivet 1010–26–10 Round Hole Plug 1010–26–85 Upright, Latch 1010–26–12...
Pneumatic Fowler Assembly (Fiberresin) Assembly part number 1210–31–120 Item Part No. Part Name Qty. 4–161 Hex Soc. But. Hd. Cap Screw 7–20 Truss Hd. Mach. Screw 25–124 Pop Rivet 15–37 Jam Nut 15–50 Hex Nut 16–28 Nylock Nut 21–125 Set Screw 21–126 Set Screw 1001–1–36...
Page 59
Pneumatic Fowler to Frame Assembly Assembly part number 1710–31–10 Item Part No. Part Name Qty. 4–182 But. Hd. Cap Screw 4–183 But. Hd. Cap Screw 11–179 Nylon Washer 14–21 Nylon Washer 16–11 Nylock Hex Nut 16–35 Nylock Hex Nut 23–100 Self–Tapping Screw 25–50 Pop Rivet...
Page 60
Pneumatic Fowler Assembly (Fiberresin) Assembly part number 1710–31–120 Item Part No. Part Name Qty. 4–161 Hex Soc. But. Hd. Cap Screw 7–20 Truss Hd. Mach. Screw 25–124 Pop Rivet 15–37 Jam Nut 15–50 Hex Nut 16–28 Nylock Nut 21–125 Set Screw 21–126 Set Screw 1001–1–36...
Page 61
Outer Housing Assembly, Right and Left Assembly part number 1210–31–106 (Right) Item Part No. Part Name Qty. 25–144 Semi–Tubular Rivet 1210–31–103 Pivot Tab 1210–31–104 Outer Housing, Right Assembly part number 1210–31–107 (Left) Item Part No. Part Name Qty. 25–144 Semi–Tubular Rivet 1210–31–103 Pivot Tab 1210–31–105...
Crank Fowler Assembly (Fiberresin) Assembly part number 1210–33–10 Item Part No. Part Name Qty. Item Part No. Part Name Qty. 4–97 Hex But. Hd. Cap Screw 25–50 Pop Rivet 4–183 But. Hd. Cap Screw 946–1–64 Fowler Operation Label 1 7–20 Truss Hd.
Page 64
Crank Fowler Assembly (Fiberresin) Assembly part number 1710–33–10 Item Part No. Part Name Qty. Item Part No. Part Name Qty. 4–97 Hex But. Hd. Cap Screw 25–50 Pop Rivet 4–183 But. Hd. Cap Screw 946–1–64 Fowler Operation Label 1 7–20 Truss Hd.
Stationary Foot End Assembly (Fiberresin) Assembly part number 1010–332–20 Item Part No. Part Name Qty. 1010–332–21 Ftsec. Skin, Fiberresin 7900–1–102 Velcro Pile 24 1/2” 25–50 Pop Rivet...
Page 67
Stationary Foot End Assembly (Steel) Assembly part number 1010–232–20 Item Part No. Part Name Qty. 1010–232–21 Ftsec. Skin, Fiberresin 7900–1–102 Velcro Pile 24 1/2” 25–122 Pop Rivet...
Page 68
Stationary Foot End Assembly (Fiberresin) Assembly part number 1510–332–20 Item Part No. Part Name Qty. 1510–332–21 Ftsec. Skin, Fiberresin 7900–1–102 Velcro Pile 24 1/2” 25–50 Pop Rivet...
Page 69
Stationary Foot End Assembly (Steel) Assembly part number 1510–232–20 Item Part No. Part Name Qty. 1510–232–21 Ftsec. Skin, Fiberresin 7900–1–102 Velcro Pile 24 1/2” 25–122 Pop Rivet...
Page 70
Crank Knee Gatch Assembly (Fiberresin) Assembly part number 1010–534–10 Frame Assembly (Ref.) Item Part No. Part Name Qty. (page 57) Knee Gatch Assembly 1010–334–27 Midsection Skin 1010–334–28 Thigh Skin 1010–334–126 Calf Skin 25–50 Pop Rivet...
Page 71
Crank Knee Gatch Assembly (Steel) Assembly part number 1010–434–10 Frame Assembly (Ref.) Item Part No. Part Name Qty. (page 57) Knee Gatch Assembly 1010–234–27 Midsection Skin 1010–234–28 Thigh Skin 1010–234–126 Calf Skin 25–122 Pop Rivet...
Knee Gatch Assembly Assembly part number 1010–434–20 Item Part No. Part Name Qty. Item Part No. Part Name Qty. 3–47 Hex Hd. Cap Screw 721–31–65 Litter Hole Plug 3–76 Hex Hd. Cap Screw 946–1–65 Label, Gatch Symbol 4–105 Soc. Hd. Cap Screw (page 61) Gatch Crankscrew Ass’y 1 7–20...
Page 73
Crank Knee Gatch Assembly (Fiberresin) Assembly part number 1510–534–10 Frame Assembly (Ref.) Item Part No. Part Name Qty. (page 60) Knee Gatch Assembly 1510–334–27 Midsection Skin 1510–334–28 Thigh Skin 1510–334–126 Calf Skin 25–50 Pop Rivet...
Page 74
Crank Knee Gatch Assembly (Steel) Assembly part number 1510–434–10 Frame Assembly (Ref.) Item Part No. Part Name Qty. (page 60) Knee Gatch Assembly 1510–234–27 Midsection Skin 1510–234–28 Thigh Skin 1510–234–126 Calf Skin 25–122 Pop Rivet...
Knee Gatch Assembly Assembly part number 1510–434–20 Item Part No. Part Name Qty. Item Part No. Part Name Qty. 3–47 Hex Hd. Cap Screw 721–31–65 Litter Hole Plug 3–76 Hex Hd. Cap Screw 946–1–65 Label, Gatch Symbol 4–105 Soc. Hd. Cap Screw (page 61) Gatch Crankscrew Ass’y 1 7–20...
Page 76
1001–34–19 Knee Gatch Crankscrew Assembly Item Part No. Part Name Qty. 946–33–18 Crank Disk 1550–1–16 Crank Assembly 26–45 Roll Pin 26–14 Roll Pin 81–176 Thrust Washer 81–175 Thrust Bearing 81–174 Thrust Washer 938–1–175 Bearing Assembly 938–1–177 Knob 378–24–29 Shoulder Bolt 16–5 Conelock Nut 1001–34–47...
Four Corner Option Assembly Assembly part number 1009–153 Item Part No. Part Name Qty. 4–156 But. Hd. Cap Screw 16–6 Kep Nut 1009–30–36 Corner Cover...
Head End Push Bar Option Assembly Assembly part numbers 1009–155 & 1509–155 Item Part No. Part Name Qty. 3–47 Hex Hd. Cap Screw 3–50 Hex Hd. Cap Screw 16–28 Nylock Nut 1010–254–4 P.U.P. Receptacle Wldmt., Lt. 1010–254–6 P.U.P. Receptacle Wldmt., Rt.
2–Stage I.V. Pole Mounting Assembly, Head End Assembly part numbers 1009–110 & 1509–110 Item Part No. Part Name Qty. 3–50 Hex Hd. Cap Screw 4–66 Soc. Hd. Cap Screw 4–91 But. Hd. Cap Screw 4–156 Hex Soc. But. Hd. Cap Screw 11–16...
Page 80
2–Stage I.V. Pole Mounting Assembly, Foot End Assembly part numbers 1009–112 & 1509–112 Item Part No. Part Name Qty. 3–50 Hex Hd. Cap Screw 4–66 Soc. Hd. Cap Screw 4–91 But. Hd. Cap Screw 4–156 Hex Soc. But. Hd. Cap Screw 11–16...
2–Stage I.V. Pole Assembly Assembly part number 1211–110–10 Item Part No. Part Name Qty. 1001–59–32 Base Tube Assembly 1001–59–31 Extension Tube Assembly 1210–110–47 Lock Ring 1210–110–49 Lock Actuator 14–20 Nylon Flat Washer As Req’d 1010–59–16 I.V. Hook 52–17 Nylon Spacer 926–400–62 Stop Sleeve 1210–110–46...
3–Stage I.V. Pole Mounting Assembly, Head End Assembly part numbers 1009–111 & 1509–111 Item Part No. Part Name Qty. 3–50 Hex Hd. Cap Screw 4–66 Soc. Hd. Cap Screw 4–91 But. Hd. Cap Screw 4–156 Hex Soc. But. Hd. Cap Screw 11–16...
Page 84
3–Stage I.V. Pole Mounting Assembly, Foot End Assembly part numbers 1009–113 & 1509–113 Item Part No. Part Name Qty. 3–50 Hex Hd. Cap Screw 4–66 Soc. Hd. Cap Screw 4–91 But. Hd. Cap Screw 4–156 Hex Soc. But. Hd. Cap Screw 11–16...
3–Stage I.V. Pole Assembly Assembly part number 1010–61–10 Item Part No. Part Name Qty. 1010–61–24 Base Tube Assembly (page 72) 2nd Stage Assembly (page 73) 3rd Stage Assembly 26–6 Roll Pin 7–4 Truss Hd. Mach. Screw 52–17 Nylon Spacer 1010–59–16 I.V.
Page 86
3–Stage I.V. Pole Assembly Assembly part number 1510–61–10 Item Part No. Part Name Qty. 1010–61–24 Base Tube Assembly (page 72) 2nd Stage Assembly (page 73) 3rd Stage Assembly 26–6 Roll Pin 7–4 Truss Hd. Mach. Screw 52–17 Nylon Spacer 1010–59–16 I.V.
Page 87
2nd Stage Assembly Assembly part number 1010–61–25 Item Part No. Part Name Qty. 1010–61–30 2nd Tube Assembly 1210–110–46 Back–Up Ring 1210–110–47 Lock Ring 1210–110–49 Lock Actuator...
3rd Stage Assembly Assembly part number 1010–61–20 Item Part No. Part Name Qty. 38–303 Spring 1010–61–13 Ball Retainer 1010–61–15 Stop Nut 1010–61–16 Retaining Shaft 1010–61–17 Thumb Knob 1010–61–18 Hand Guard 1010–61–19 3rd Extension Rod 31–21 Ball...
Page 89
Tethered I.V. Pole Mounting Assembly Assembly part number 1001–87–20 Item Part No. Part Name Qty. (page 75) Trough Assembly (page 76) I.V. Pole Assembly 34–22 Cord Clamp 25–79 Pop Rivet 4–85 Soc. Hd. Cap Screw 16–3 Nylock Nut...
Page 90
Tethered I.V. Pole Trough Assembly Assembly part number 1001–87–22 Item Part No. Part Name Qty. 1001–87–23 Machined Sleeve 1001–87–16 Front Mounting Bracket 1001–87–15 Mounting Bracket Ass’y 1–22 Flat Hd. Mach Screw 37–2 Tube Plug 946–40–110 Lock Clip 16–14 Dynalock Hex Nut...
Page 91
Tethered I.V. Pole Assembly Assembly part number 1001–87–18 Item Part No. Part Name Qty. (page 77) I.V. Holder 1010–22–27 Cable Assembly 741–47–14 Retainer 21–16 Set Screw...
Page 92
I.V. Holder Assembly Assembly part number 721–47–6 Item Part No. Part Name Qty. 938–1–305 Pole Socket Assembly 938–1–308 Pole Assembly 24–53 Knob...
Page 93
Fowler X–Ray Cassette Assembly Assembly part number 1001–23–10 Item Part No. Part Name Qty. 1001–23–12 Tray 1020–23–16 Post Housing 1001–23–14 Actuating Rod 926–23–64 Post 1010–23–37 Rod Guide 1020–23–21 Knob 1010–23–28 Tray Angle 926–23–70 Block Assembly 926–23–69 Washer 14–3 Washer 38–122 Compression Spring 1020–23–26 Spacer...
Page 94
X–Ray Cassette Installation Assembly Assembly part number 1001–23–11 Item Part No. Part Name Qty. (page 78) X–Ray Cassette Ass’y 16–3 Self–Locking Nut 4–147 Button Hd. Cap Screw 1001–23–13 Tray Latch 1020–23–13 Tray Hinge, Right 1020–23–12 Tray Hinge, Left 25–69 Pop Rivet...
Foot Board/Chartholder Assembly Assembly part number 926–40–10 Item Part No. Part Name Qty. 946–28–11 Chart Holder 946–29–6 Foot Board Upright Oxygen Bottle Holder Assembly Assembly part number 1020–30 Item Part No. Part Name Qty. 1020–30–11 Upright Bottle Holder 27–12 Cotter Pin 1020–30–17 Specification Label...
Defibrillator Tray Assembly Assembly part number 926–39–10 Item Part No. Part Name Qty. Item Part No. Part Name Qty. 946–39–4 Tray 926–1–82 Label 926–39–16 Crosstube 390–57–12 Long Strap 25–55 Rivet 390–57–13 Short Strap 926–39–9 Cover 946–1–283 Label 18–6 Umbrella Nut 926–39–15 Holder 7900–1–143...
Heel Stirrup and Support Assembly Assembly part number 1001–55–10 Item Part No. Part Name Qty. (Page 84) Rt. Stirrup Support Ass’y (Page 85) Lt. Stirrup Support Ass’y (Page 86) Stirrup Assembly 22–8 Drive Screw 3–78 Hex Head Cap Screw 16–28 Nylock Hex Nut 11–158 Flat Washer...
Right Stirrup Support Assembly Assembly part number 1001–55–15 Item Part No. Part Name Qty. 1010–55–16 Right Support Tube Ass’y 1001–55–11 Mounting Bracket 650–2–32 Lock Screw Assembly 966–51–19 Wedge Lock, Modified 38–171 Compression Spring 26–7 Roll Pin 14–40 Nylon Flat Washer 24–11 Knob...
Left Stirrup Support Assembly Assembly part numbe 1001–55–16 Item Part No. Part Name Qty. 1010–55–26 Left Support Tube Ass’y 1001–55–11 Mounting Bracket 650–2–32 Lock Screw Assembly 966–51–19 Wedge Lock, Modified 38–171 Compression Spring 26–7 Roll Pin 14–40 Nylon Flat Washer 24–11 Knob...
C–Spine Support Pole Assembly Assembly part number 1010–70–10 View A–A Item Part No. Part Name Qty. 1010–70–33 Support Tube Cap 26–6 Roll Pin 1010–70–34 Support Arm Weldment 1010–70–42 Cassette Holder Weldment 1010–70–50 Adjustment Tube Weldment 1010–70–30 Base Tube Weldment 1010–70–45 Knob 25–55 Pop Rivet...
If requested by Stryker, products or parts for which a warranty claim is made shall be returned prepaid to Stryker’s factory. Any improper use or any alteration or repair by others in such manner as in Stryker’s judgement affects the product materially and adversely shall...
Claim will be limited in amount to the actual replacement cost. In the event that this information is not received by Stryker within the fifteen (15) day period following the delivery of the merchandise, or the damage was not noted on the delivery receipt at the time of receipt, the customer will be responsible for payment of the original invoice in full.