Related Manuals for FiberHome AN5506-04-F
Summary of Contents for FiberHome AN5506-04-F
-
Page 1: User Manual
AN5506-04-F GPON Optical Network Unit User Manual Version: A Code: MN000000619 FiberHome Telecommunication Technologies Co., Ltd. June 2010... - Page 3 Please contact your local sales representative, service representative or distributor for any help needed at the contact information shown below. Fiberhome Telecommunication Technologies Co., Ltd. Address: No. 5 Dongxin Rd., Hongshan Dist., Wuhan, China Zip code: 430073 Tel:...
-
Page 5: Legal Notice
are trademarks of FiberHome Telecommunication Technologies Co., Ltd. (Hereinafter referred to as FiberHome) All brand names and product names used in this document are used for identification purposes only and are trademarks or registered trademarks of their respective holders. - Page 7 Operation Safety Rules High optical power can cause bodily harm, especially to eyes. Never look directly into the end of the optical transmitter fiber jumper or the end of its active connector. Exercise care if you must bend fibers. If bends are necessary, the fiber bending radius should never be less than 38mm.
- Page 8 Avoid moisture, dampness and water damage. Equipment exposed to water cannot work normally and can be extremely hazardous due to shorting. Do not lay this equipment on an unsteady base.
-
Page 9: Packing List
Packing List After opening the carton of the AN5506-04-F, refer to the following packing list to check whether the items in the carton are complete: Item Quantity Remarks AN5506-04-F Certificate of quality AN5506-04-F GPON Opitical User manual Network Unit User Manual... -
Page 11: Table Of Contents
Contents Product Introduction ................ 1-1 Product Functions ..............1-1 Product Type ................1-3 Technical Specifications ............1-3 Appearance Description ..............2-1 Top Panel and LED Indicators ..........2-1 Rear Panel and Interfaces ............ - Page 12 Checking After Installation ............3-9 FAQs ....................4-1 ...
- Page 13 Figures Figure 1-1 Network application of the AN5506-04-F ...... 1-1 Figure 2-1 Top panel of the AN5506-04-G1 ........2-2 Figure 2-2 Rear panel of the AN5506-04-G1 ......... 2-4 Figure 3-1 Dimensions of recesses on the AN5506-04-F bottom ...
- Page 15 Tables Table 1-1 Product type ..............1-3 Table 1-2 Technical specifications of the AN5506-04-F ....1-4 Table 2-1 LED indicators of the AN5506-04-G1 ......2-2 Table 2-2 Interfaces and buttons of the AN5506-04-G1 ....2-5 ...
-
Page 17: Product Introduction
Product Introduction Product Functions The AN5506-04-F is an FTTH GPON optical network unit. It provides communication and entertainment service in multiple modes such as data, voice, and video, to meet integrated access requirement of families or small enterprises. The following figure shows the network application of the AN5506-04-F:... - Page 18 (the OLT) to build a gigabit GPON system, which provides triple-play multi-service access of high capacity and reliability. The AN5506-04-F is one of the AN5506-04 series and it supports the following features: Adopts GPON interface for uplinkings, compliant with ITU-T G.984.
-
Page 19: Product Type
Table 1-1 Product type Ethernet Phone CATV Power Product Type Interface Interface Interface Interface AN5506-04-F1 Three-pin AN5506-04-G1 power jack Technical Specifications Table 1-2 lists technical specifications of the AN5506-04-F in detail. Version A... -
Page 20: Table 1-2 Technical Specifications Of The An5506-04-F
AN5506-04-F GPON Optical Network Unit User Manual Table 1-2 Technical specifications of the AN5506-04-F Type Item Description Supports the following voice protocols: H.248, MGCP, and SIP. Voice Adopts the following voice coding: G.711a/u, G.723, G.729. Supports IEEE 802.1Q VLAN. Supports adding 802.1Q VLAN in VLAN tag or untag mode. - Page 21 1 Product Introduction Type Item Description Power 15 W consumption Operating 0˚C to 45˚C temperature Environment Storage -30˚C to 60˚C parameter temperature Environment 10% to 90%, non-condensing. humidity Note: Technical specifications of the CATV interface are only supported by AN5506-04-G1. Version A...
-
Page 23: Appearance Description
Appearance Description Top Panel and LED Indicators The AN5506-04-F adopts hollow-carved streamline design with novel and fashionable appearance. You can know the running status of the device according to the LED indicators on the top panel. The following takes the AN5506-04-G1 as an example. Figure 2-1 shows the top panel of AN5506-04-G1. -
Page 24: Figure 2-1 Top Panel Of The An5506-04-G1
AN5506-04-F GPON Optical Network Unit User Manual Figure 2-1 Top panel of the AN5506-04-G1 Table 2-1 describes the LED indicators of the AN5506-04-G1. Table 2-1 LED indicators of the AN5506-04-G1 Meaning Color Status Description Indicator The device registers to the... - Page 25 2 Appearance Description Meaning Color Status Description Indicator The device is powered off. The device registers to the Indicator of GPON system. registration Green The device fails to status register to the GPON system. The device fails to receive the optical Indicator of signal.
-
Page 26: Rear Panel And Interfaces
Rear Panel and Interfaces All interfaces and buttons of AN5506-04-F are distributed on the rear panel of the device, with a compact shape and good utility. The following takes the AN5506-04-G1 as an example. Figure 2-2 shows the rear panel of AN5506-04-G1. -
Page 27: Table 2-2 Interfaces And Buttons Of The An5506-04-G1
2 Appearance Description Table 2-2 Interfaces and buttons of the AN5506-04-G1 Interface Meaning Type Description or Button Turn on or off the Power switch Button power. For connecting the AC Power power adapter with Power interface Power three pins or power interface with three adapter with storage... -
Page 29: Product Installation
Preparation Before Installation 3.1.1 Checking Items in the Package After opening the carton of the AN5506-04-F, refer to the packing list to check items in the carton. If the items do not match the packing list, contact the local office of FiberHome. -
Page 30: Placing The Device
Placing the Device The AN5506-04-F can be placed on a stable plane (such as a desk), or be hung on the wall. You can select the suitable installation mode. The AN5506-04-F can be placed in the two modes as follows. -
Page 31: Cable Connection
Cable Connection 3.3.1 Connecting the Network Cable You can connect the Ethernet interfaces of the AN5506-04-F to user terminals, such as PCs and switches, by using network cables. See Figure 3-2. Follow these steps to connect the network cable. 1) Plan the cabling mode of the network cable, measure the distance between the LAN interface of the AN5506-04-F and the user terminal, and select the network cable of proper length. -
Page 32: Figure 3-2 Cable Connection (Three-Pin Power)
Note 1: Transmission distance of the network cable is shorter than 100m. Therefore, the network cable you prepare should not exceed 100m. Note 2: The Ethernet interfaces of the AN5506-04-F support MDI/MDIX, self-adaption. You can use the straight-through or cross-over network cable for cabling. Figure 3-2... -
Page 33: Connecting The Phone Cable
3 Product Installation 3.3.2 Connecting the Phone Cable The AN5506-04-F offers two phone interfaces to provide voice service. Follow these steps to connect the voice cable: 1) Plan the cabling mode of the phone cable, measure the distance between the Phone interface of the AN5506-04-F and your phone, and select the phone cable of proper length. -
Page 34: Connecting The Fiber
Remove the fiber cover. See Figure 3-3. Figure 3-3 Fiber connection (1) Wrap the fiber jumper along the groove on the bottom panel and insert one end to the PON interface of the AN5506-04-F. See Figure 3-4. Version A... -
Page 35: Figure 3-4 Fiber Connection (2)
3 Product Installation Figure 3-4 Fiber connection (2) Close the fiber cover and the connection is complete. See Figure 3-5. Figure 3-5 Fiber connection (3) Version A... -
Page 36: Connecting The Power Cable
AN5506-04-F GPON Optical Network Unit User Manual 3.3.5 Connecting the Power Cable The AN5506-04-F provides two types of power adapters: a power adapter with three pins and a power adapter with battery. Connecting the Power with Three Pins 1) Take out the power adapter with three pins included in the package. -
Page 37: Figure 3-6 Cable Connection
Cable connection Checking After Installation After the cable connection is complete and relevant services are applied to your ISP, you need to power on the AN5506-04-F and do the following checking: 1) Turn on the power. 2) Observe the status of the Power indicator. If the Power indicator is on, the the device is normally powered on. - Page 38 7) When the device is running, ensure ventilation, to avoid anomalies because of overheating. For abnormity, contact the local office of FiberHome for replacement, to prevent impact on the device usage. 3-10 Version A...
- Page 39 FAQs Q: Why are all LED indicators off after the device is powered on? A: 1) Check whether the power connection cable is connected properly. Check whether the power switch on the front panel of the device is turned on. Q: Why does the device fail to work after running normally for a period? A: 1)
- Page 40 AN5506-04-F GPON Optical Network Unit User Manual The upstream equipment is faulty. The optical power is out of the normal range (such as overload). Q: Why does the Battery indicator blink or turn off? A: 1) If the Battery indicator blinks, the battery works abnormally or the voltage is over low.
- Page 41 FiberHome. 1. Please give your opinions on the items listed below about this manual by the symbol “”. Items Excellent Good Normal Expres sion ...
- Page 44 FiberHome Telecommunication Technologies Co., Ltd. Address: No. 5 Dongxin Rd., Hongshan Dist., Wuhan, China Zip code: 430073 Tel: +86-27-87691549 Fax: +86-27-87691755 Website: http://www.fiberhomegroup.com...