FiberHome AN5506-04-F User Manual

A N 5 5 0 6 - 0 4 F -
GPON
Optical Network Unit
C o d e : M N 0 0 0 0 0 0 6 1 9 V e r s i o n : C

User Manual

Thank you for choosing FiberHome products.
Packing List:
● AN5506-04: 1 DC or storage batter y power adapter : 1 RJ 45 cr ystal head: 5 ● ● -
● RJ 11 cr ystal head 3 User Manual 1 Certificate: 1. Please contact your supplier if - : ● : ●
anything is missing.
Operation Safety Rules
For a correct, safe use of the equipment, please read the following carefully and st rictly obser ve the operation
safety rules during your operations.
High optical power can cause bodily harm, especially to eyes. Never look directly into the
end of the optical transmitter fiber jumper or the end of its active connector.
Exercise care if you must bend fibers. If bends are necessar y, the fiber bending radius should
never be less than 38mm.
Power socket overload, broken cables or broken plugs may cause electric shock or fire.
Regular check-ups on power supply wires and cables are essential. If any appears damaged,
replace at once.
Use the power supply adapter provided in the package only. Using other adapters may cause
equipment damage or operation failures.
Install the equipment in a well ventilated environment without high temperatures or direct
sunlight to protect the equipment and its components from overheating, which can result in
damage.
Avoid moisture, dampness and water damage. Equipment exposed to water cannot work
normally and can be extremely hazardous due to shorting.
Do not lay this equipment on an unsteady base.
Product Introduction
4 GE ports and 2 phone
AN5506-04-F2G External antenna
ports
1 GE port, 3 FE ports
Built-in antenna
AN5506-04-F3
and 2 phone ports
The AN5506-04-F is an FTTH GPON optical network unit. It provides communication and entertainment ser vice in multiple modes such as
data, voice, and video, to meet integrated access requirement of families or small enterprises. The AN5506-04-F supports these functions:
Uses GPON uplink that is compliant with ITU-T G.984 series of standards;
Supports Ethernet interface rate, working mode, MDI / MDIX auto-negotiation mode;
Supports packet filtering and DoS attack protection;
Provides performance statistics on all Ethernet lines;
Supports reporting the physical position information of Ethernet interfaces through DHCP Option82;
Supports the PPPoE+ function for obtaining user IP address and accurate user identification;
Supports various voice protocols including H.248 and SIP;
Supports IGMP snooping protocol;
Supports the L2 / L3 wire speed for warding;
Supports the AES-128 algorithm for data encr yption of downlink data;
Supports global configuration of queue priority and flexible mapping of 802.1p value of packets. Supports
the PQ queue scheduling mode. You can configure the weight of scheduling queue to ensure the QoS of the
ser vices with high QoS requirement such as voice and video under multiple ser vice conditions;
Supports wireless access mode, compliant with the 802.11 b/g/n standard;
Supports the following authentication modes: open, shared, wpapsk , wpa2psk , wpapskwpa2psk . Supports
the following encr yption modes: none, wep, tkip, aes, and tkipaes.
Technical Specification
Type
Item Description
Dimension
45 mm×235mm×174mm H W D) (
Mechanical
parameters Weight
390g approximately
Power supply
DC
DC 12V 1 5A / .
parameter
Power consumption
AN5506-04-F 12W
parameter
Operating temperature -5℃ to 45℃
Environmental
Storage temperature -30℃ to 60℃
parameter
Environmental humidity 10% to 90% , non-condensing
Indicator LED Description
Ethernet interface status LED (Green)
VOIP status LED (green)
ON: The interface is connected to the user terminal
ON: The equipment registers to the
without data transmission
softswitch system successfully
Blinking: The interface is transmitting
OFF: The equipment does not
and receiving data
register to the softswitch system
OFF: The interface is not connected
to the user terminal
Power status LED (green) Phone port LED (green)
ON: The equipment is ON: The equipment registers to the
powered on softswitch platform successfully
OFF: The equipment is not Blinking: The port is transmitting ser vice flow
powered on ON: The equipment fails to register to the
softswitch platform
1 2
Optical signal status LED (red)
Blinking: The equipment receives no
Registration status LED (green) Wireless signal status LED (green)
optical signal. ON: The wireless interface is enabled
ON: The ONU is activated
Blinking: Ser vice flow transmission exists
OFF: The equipment receives optical
OFF: The ONU is not activated
OFF: The wireless interface is disabled
signals.
USB LED (green)
ON: The USB is connected without data transmission
Blinking: The USB is transmitting and receiving data
OFF: The USB is not connected
Equipment Installation
The AN5506-04-F can be horizontally or vertically placed on a desk , or hung against the wall.
Horizontally placed Verticall placed
Wall Mounting
1. Mark the installation 2. Drill two holes and install 3. Install screws and hang the
position expansion bolts equipment on them
Interfaces and Connections
1. Network interface 2. Voice interface 3. Optical interface
4. Power switch 5. Power interface
1 2 3 4 5
Best antenna position
Laptop
Power
Smart
adapter
phone
PC Phone Optical
interface
AN5506 04 F3 Side Panel - -
6 7 8 9 10 11
6. LAN switch
7. Button for setting WI FI -
safety protection
8. Reset key
9. Wireless switch
10. LED switch
11. USB interface
AN5506 04 F2G Side Panel - -
12 13 14 15
12 Button for setting WI FI . -
safety protection
13 Reset key .
14 Wireless switch .
15 USB interface .